GGBEE 433MHz Wireless Light Switch

Contents

GGBEE 433MHz Wireless Light Switch Instruction Manual

Model: 433MHz Wireless Light Switch

1. Product Overview

The GGBEE 433MHz Wireless Light Switch system provides convenient remote control for your lighting. It consists of a compact receiver module and wireless remote control buttons that can be placed anywhere without wiring.

GGBEE 433MHz Wireless Light Switch system showing the receiver module and two round remote control buttons.

Figure 1: GGBEE 433MHz Wireless Light Switch components.

GGBEE wireless wall switch and receiver module in a living room setting.

Figure 2: Wireless wall switch and receiver module in use.

2. Setup and Installation

2.1 Wiring the Receiver Module

Ensure power is OFF at the main circuit breaker before proceeding with any wiring. Incorrect wiring can cause damage or injury.

Wiring diagram for the GGBEE 433MHz receiver module connecting to AC input and a light bulb output, with a remote control button below.

Figure 3: Receiver wiring diagram.

  1. Connect the Live line (from power source) to the terminal labeled Lin on the receiver.
  2. Connect the Neutral line (from power source) to the terminal labeled Nin on the receiver.
  3. Connect the Light Live line (to the light fixture) to the terminal labeled Lout on the receiver.
  4. Connect the Light Neutral line (to the light fixture) to the terminal labeled Nout on the receiver.

2.2 Remote Control Battery Installation

The remote control buttons use a CR2016 battery. Open the back cover of the remote button and insert the CR2016 battery with the positive (+) side facing up.

2.3 Pairing the Remote Control with the Receiver

Follow these steps to pair your remote control button(s) with the receiver module:

Instructions on how to pair (get signals) and unpair (clear signals) the GGBEE 433MHz receiver with the remote control.

Figure 4: Signal learning and clearing instructions.

  1. Step 1: Press the learning button on the receiver module twice. Wait for 3 seconds.
  2. Step 2: Press one button on the remote control. Wait for 3 seconds. The pairing is successful.

2.4 Remote Control Placement

The wireless remote control buttons offer flexible placement options:

Diagram showing flexible placement options for the GGBEE wireless remote switch: on glass, on a wall, on a bedside table, or held in hand.

Figure 5: Flexible placement options for the remote control.

  • Stick on glass (using double-sided tape).
  • Put on the wall (using double-sided tape).
  • Place freely on any surface (e.g., bedside table).
  • Hold in hand for portable control.

3. Operating Instructions

3.1 Basic ON/OFF Operation

Once paired, simply press the remote control button to toggle the connected light ON or OFF.

GGBEE wireless remote switch being used to control a bedside lamp.

Figure 6: Remote control in action.

3.2 Advanced Learning Functions

The receiver module supports various learning modes for specific behaviors:

  • Learning Switch (Toggle Mode): Press the learning button once. The remote control's long press light will flash twice.
  • Learning ON (Momentary ON): Press the learning button twice continuously. The remote control's long press light will flash twice.
  • Learning OFF (Momentary OFF): Press and hold the learning button three times in a row. The remote control light will flash twice.
  • Default ON at Power-up: Press the learning button 6 times in a row. The light will flash 3 times. The light will turn on by default when the receiver is powered on.
  • Default OFF at Power-up: Press the learning button 7 times in a row. The light will flash 3 times. The light will remain off when the receiver is powered on.

3.3 Video Demonstration

Video: Product demonstration, wiring, pairing, and operation of the GGBEE 433MHz Wireless Light Switch.

4. Maintenance

4.1 Battery Replacement

When the remote control button's indicator light becomes dim or unresponsive, replace the CR2016 battery. Ensure correct polarity (+ side up).

4.2 Cleaning

Wipe the receiver and remote control surfaces with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.

5. Troubleshooting

  • Light does not respond to remote:
    • Check if the receiver is properly wired and receiving power.
    • Ensure the remote control battery is installed correctly and has sufficient charge.
    • Re-pair the remote control with the receiver (refer to Section 2.3).
  • Remote control range is poor:
    • Ensure there are no major obstructions (thick walls, metal objects) between the remote and receiver.
    • Replace the remote control battery.
  • To clear all paired remote control codes:
    • Press and hold the learning button on the receiver for more than 5 seconds. The light will flash twice, indicating all remote control codes have been canceled. You will need to re-pair any remotes.

6. Specifications

FeatureSpecification
Input VoltageAC 100-240V 50/60Hz
Maximum Load2200W
Rated Current10A
Working FrequencyASK 433MHz
MaterialPlastic
CertificationCE
Switch TypeRemote Control (Push Button)
Smart DeviceNo
OriginMainland China
Receiver Size7 x 2.5 x 4.5 cm
Package Dimensions6 x 3 x 6 cm
Package Weight0.05 kg

7. User Tips

No specific user tips were available from provided reviews or Q&A content.

8. Warranty and Support

For warranty information, technical support, or any product-related inquiries, please contact your seller or the point of purchase directly.

© GGBEE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.