TOPPING E30II

Contents

TOPPING E30II Hi-Res Audio DAC & Preamplifier

Model: E30II

Introduction

Thank you for purchasing the TOPPING E30II. The E30II is a high-performance Digital-to-Analog Converter (DAC) featuring USB, coaxial, and optical inputs. It is compatible with audio up to 768kHz/32bit PCM and DSD512. Designed with full digital volume control and an LED display, the E30II can function as both a DAC and a preamplifier. We hope it enhances your music listening experience. Please read this manual thoroughly to ensure correct usage and to utilize all features of your E30II.

Package Contents

  • E30II Unit x1
  • DC Power Cable x1
  • USB Cable x1
  • Remote Control x1
  • User Manual x1
  • Warranty Card x1

Product Overview

Front Panel

TOPPING E30II Front Panel

Image: Front view of the TOPPING E30II, showing the LED display and the multifunction touch button.

  1. LED Screen: Displays current status, sampling rate, or volume.
  2. Remote Control Receiver: Receives signals from the remote control.
  3. Multifunction Touch Button: Used for power, standby, input switching, and menu navigation.

Rear Panel

TOPPING E30II Rear Panel Connections

Image: Rear view of the TOPPING E30II, showing all input and output ports.

  1. Right Channel Single-Ended RCA Output
  2. Left Channel Single-Ended RCA Output
  3. Coaxial SPDIF Input
  4. Optical SPDIF Input
  5. USB Input
  6. DC5V/1A Power Input

Remote Control Functions

The remote control provides convenient access to various functions:

  • Standby: Toggles standby mode.
  • Volume Up/Down: Adjusts output volume in PRE mode.
  • Input Switching: Cycles through available input sources (USB, Optical, Coaxial).
  • Filter Setting: Selects PCM or DSD filter modes.
  • Mute: Toggles audio output mute.
  • OK Button: Confirms selections in the setup menu.
  • Brightness: Adjusts screen brightness.

Specifications

Attribute Value
Dimensions10.0cm x 12.5cm x 3.2cm
Weight295g
Power InputDC5V/1A
Signal InputsUSB Type-B, Optical (SPDIF), Coaxial
Line Out OutputRCA
MaterialMetal
PCM Sampling Frequencies44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz, 705.6 kHz, 768 kHz
PCM Word Length16-bit, 24-bit, 32-bit
DSD Sampling Frequencies2.8224 MHz (DSD64), 5.6448 MHz (DSD128), 11.2896 MHz (DSD256), 22.5792 MHz (DSD512)
THD+N (1kHz A-wt)<0.00015%
THD (No-wt 20-20kHz)<0.00060%
SNR (A-wt)123dB @1kHz
Dynamic Range (A-wt)123dB @1kHz
Frequency Response20Hz-20kHz (±0.3dB), 20Hz-40kHz (±0.8dB)
Output Level2.1Vrms @0dBFS
Noise (A-wt)<1.5uVrms
Channel Crosstalk (1kHz)-132dB
Channel Balance0.3dB
Output Impedance200Ω

Note: All specifications are measured in TOPPING laboratory.

Setup

Power On/Off/Standby Operation

  • Power On: Connect the DC5V/1A power supply. The E30II will enter standby mode, and a bright dot will appear on the screen.
  • Standby: While the unit is operating, press and hold the multifunction touch button on the front panel for 5 seconds to enter standby. A short press will exit standby. Alternatively, use the standby button on the remote control.
  • Automatic Standby: If no valid input signal is detected for 1 minute, the E30II will automatically enter standby. It will resume operation once a valid signal is detected.

Connections

  1. Connect your audio source (e.g., computer, CD player) to the E30II's USB, Optical, or Coaxial input.
  2. Connect the E30II's RCA outputs to your amplifier or active speakers using RCA cables.
  3. Connect the DC5V/1A power adapter to the E30II's power input.

Input Selection

Press the multifunction touch button on the front panel or use the 'Switch to previous input' / 'Switch to next input' buttons on the remote control to cycle through the available input sources.

Volume Control

  • PRE (Preamplifier) Mode: In this mode, the E30II's volume is adjustable. Use the Volume Up/Down buttons on the remote control. Long-pressing these buttons will adjust the volume quickly. Exercise caution to protect your hearing.
  • DAC Mode: In this mode, the volume is fixed at 0dB and is not adjustable. The E30II functions as a pure DAC.
  • Mute: Press the Mute button on the remote control to mute the audio output. Press it again or adjust the volume to unmute.

Operating

Setup Menu

The setup menu allows you to customize various settings of the E30II.

  • Accessing the Menu: In standby mode, press and hold the multifunction touch button on the front panel for 5 seconds.
  • Navigating and Saving Settings (Front Panel):
    • Short press the multifunction button to move to the next setting item.
    • Double press to change the parameter for the current item.
    • Long press until "8-8" is displayed on the screen to save your settings.
  • Navigating and Saving Settings (Remote Control):
    • Use the Volume Up/Down buttons to move to the previous/next setting item.
    • Use the Left/Right input switching buttons to change parameters.
    • Press the OK button. The screen will display "8-8" to indicate that settings have been saved.

Setting Descriptions

Setting Options Description
PCM Filter (F-1 to F-6)Sharp Roll-off (Default), Slow Roll-off, Short Delay Sharp Roll-off, Short Delay Slow Roll-off, Super Slow Roll-off, Low Dispersion Short Delay FilterSelects different digital filters for PCM playback.
DSD Filter (F-1 to F-2)39kHz (Default), 70kHzSelects different digital filters for DSD playback.
Screen Brightness (L-1 to L-3, L-A)Low, Mid (Default), High, L-A (Auto-off)Adjusts the brightness of the LED display. L-A mode turns off the screen after 30s of inactivity, showing only current input.
Automatic Standby (A-0, A-C)Auto On (Default), Auto OffEnables or disables the automatic standby feature.
Output Mode (o-d, o-P)DAC Mode (Volume non-adjustable), Pre-Amp Mode (Volume adjustable) (Default)Switches between pure DAC output and preamplifier output.
Remote Control (r-C, r-0)Remote control enabled (Default), Remote control disabledEnables or disables the remote control functionality.

Factory Reset

To restore the E30II to its factory default settings, in standby mode, press the Volume Down, Volume Up, and Mute buttons on the remote control in sequence.

Maintenance

  • Do not ground or short-circuit the output jacks.
  • Avoid placing the product in hot, humid environments, and protect it from rain or strong impacts.
  • Do not attempt to repair or disassemble the product yourself. If service is required, please contact professional repair personnel.
  • The manufacturer is not responsible for any direct or indirect loss or damage caused by product failure.

Troubleshooting

Phenomenon Possible Cause Solution
Input indicator flashes Unknown signal format, No signal input Change to correct format, Check/change cable, Check player
USB not recognized / USB input no sound PC's USB port damaged, PC not working, Too low volume on PC, E30II not selected as output device on PC Check/change cable, Change another port, Try another PC, Enable OTG function, Adjust volume, Set E30II as default output device
INL Err (Supply voltage error) Supply voltage too high/low Ensure DC5V power supply

User Tips

  • Experiment with Filters: The E30II offers 6 different PCM filters and 2 DSD filters. Experimenting with these can help you find a sound profile that suits your preference, potentially enhancing texture and nuance in your audio.
  • Volume Control: The device can function as a pure DAC with fixed output or as a preamplifier with adjustable volume via the remote control. Ensure you are in the correct output mode (PRE or DAC) for your desired functionality.
  • Soundstage Improvement: Some users have noted improved intimacy and soundstage, especially when paired with a suitable headphone amplifier.

Warranty & Support

For the latest electronic manuals and drivers, please visit the official TOPPING website: http://www.topping.audio/.

A detailed user manual is also available in PDF format for download: TOPPING E30II User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.