1. Overview
The Fingerbot (Zigbee) is a compact robot designed for intelligently controlling various buttons and switches in your home. It allows you to automate existing home appliances by physically pressing buttons or toggling switches. With the Fingerbot, you can schedule tasks, activate devices via voice commands, and remotely control your home or office equipment, making daily routines effortless.
2. Setup
2.1 App Installation
The Smart Life App is the mobile platform required for controlling IoT devices like the Fingerbot. To install the app, search for "Smart Life" in your mobile application store.
2.2 Device Power
Before initial use, open the back cover of the Fingerbot and remove the battery insulation sheet to power on the device.
2.3 Device Resetting
A device reset is necessary when pairing your Fingerbot with the app. Press and hold the reset button for 5 seconds until the blue light begins flashing. This indicates the device is in pairing mode.
2.4 Device Pairing
Open the Smart Life App, tap the '+' button in the top right corner, and then select 'add device'. Ensure your network is a 2.4GHz network. Follow the on-screen instructions to complete the device pairing process.
2.5 Physical Installation
- Clean the surface of the button panel where the Fingerbot will be installed.
- Use the double-sided tape provided in the Fingerbot packaging to securely attach the Fingerbot to the panel.
- Connect your Fingerbot to the app and calibrate the movement of the Fingerbot arm to precisely fit the button. Set the "Downward Movement" parameter to a value that ensures the Fingerbot arm can effectively press the button.
- After installation, allow the device to settle for 24 hours to achieve maximum adhesive strength.
3. Operation
3.1 Device Control (Triggering)
To trigger an action, simply click the Fingerbot action button within the device panel of the Smart Life App. The action will execute within 2 seconds, provided there is good signal reception.
3.2 Parameter Adjustment
Access the device control panel in the app to fine-tune the Fingerbot arm's parameters. This includes mode selection, up/down movement range, and holding time. It is crucial to set these parameters correctly to ensure optimal performance and longevity of the device.
Note: Improper settings can lead to abnormal operation and reduce the Fingerbot's lifespan. We recommend waiting at least 30 seconds after each device click to ensure optimal performance and prevent over-stressing the mechanism.
4. Maintenance
4.1 Battery Replacement
The Fingerbot uses a replaceable CR2 3.0V battery. If the arm's movement becomes erratic or stops, it may be time to replace the battery. To do so, open the back case and insert a new CR2 3.0V battery, ensuring correct polarity.
4.2 Replaceable Arm
The Fingerbot features a modular design with a replaceable arm, allowing for adaptability to various situations. A Fingerbot Toolpack (sold separately) includes three types of arms. Additionally, a free 3D printing template is available at www.adaprox.io for creating custom Fingerbot arms.
5. Troubleshooting
If you encounter issues with your Fingerbot Plus, please refer to the following common problems and solutions:
- Device not pairing or showing "not authorized" error: Ensure your Wi-Fi network is 2.4GHz. Try resetting the device by holding the button for 5 seconds until the blue light flashes. If the issue persists, it may indicate a compatibility problem or a faulty unit.
- Device not communicating with Gateway: Verify that your Zigbee Gateway is properly set up and within range of the Fingerbot. Check network connectivity for both devices.
- Arm not moving as expected or broken: Ensure the battery is correctly installed and has sufficient charge. Check for any obstructions to the arm's movement. If the arm is physically damaged, it may need to be replaced (see Section 4.2).
- Product not working after setup: Review the parameter adjustments in the app (Section 3.2) to ensure the arm's movement and holding time are correctly calibrated for your specific button/switch.
Warning:
- This product is not waterproof. Do not install it on underwater equipment.
- The product contains a battery and should not be used in humid or high-temperature environments.
- Do not obstruct the movement of the Fingerbot's arm during operation. Doing so may cause the arm to detach and damage the internal motors.
6. Specifications
| Feature | Detail |
|---|---|
| Dimensions | 34.5 x 34.5 x 34.5 mm |
| Weight | 38 g |
| Maximum Movement | 12 mm |
| Pushing Force | 10 N |
| Wireless Protocol | Zigbee 3.0 |
| Battery Type | CR2 3.0V |
| Working Temperature | -10°C ~ 45°C / 14°F ~ 113°F |
7. User Tips
- For optimal performance and to extend the Fingerbot's lifespan, ensure you wait at least 30 seconds between consecutive clicks.
- Carefully calibrate the arm's movement in the app to avoid excessive resistance, which can shorten the device's life.
- When installing with adhesive tape, allow 24 hours for the adhesive to fully cure before heavy use to ensure maximum adhesion.
- If you encounter persistent "not authorized" errors during pairing, double-check your network settings (must be 2.4GHz) and consider contacting customer support for assistance.
8. Warranty & Support
For detailed warranty information and further support, please refer to the official product documentation. A comprehensive user manual PDF is available for download:
If you experience any issues not covered in this manual or require technical assistance, please contact the seller or manufacturer's customer support.