Heltecbms HT-610L Series

Contents

Heltec HT-610L Series Battery Management System User Manual

Model: HT-610L Series | Brand: Heltecbms

Heltec HT-610L Series BMS boards with wiring harnesses

Overview of Heltec HT-610L Series Battery Management System boards.

1. Product Introduction

The Heltec HT-610L Series Battery Management System (BMS) is an intelligent balancing protection board designed for 6S-10S series lithium batteries. It supports both ternary lithium (NCM) and lithium iron phosphate (LFP) battery types.

Key features include protection against overcharging, over-discharging, over-current, over-temperature, and short circuits. It also provides balanced charging to maintain battery health and extend the service life of the battery pack. The system ensures that once an individual cell voltage reaches the equilibrium turn-on voltage, high voltage batteries are balanced until the equilibrium release voltage is achieved.

2. Product Model Selection

The HT-610L series is available in various configurations. The table below outlines the currently available models:

Parameter Value
Number of Strings 6S-10S
Continuous Discharge Current 30A/60A
Applicable Battery Type NCM/LFP

Note: Customization for 6-10S series is supported for other requirements.

3. Product Model Description

Model numbers follow a specific convention. For example, a 30A protective board with 10 strings can be interpreted as follows:

  • HT-610 LOS 10S 30A
  • HT-610 LPS 8S 30A

Breakdown of the model naming convention:

  • 610: Indicates this series can produce 6 to 10 strings.
  • LOS: Indicates the BMS is for NCM (Ternary Lithium) batteries.
  • LPS: Indicates the BMS is for LFP (Lithium Iron Phosphate) batteries.
  • 10S: Represents the number of strings (cells in series) the BMS board supports.
  • 30A: Denotes the continuous discharge current of this BMS board.

4. Specifications

4.1. General Product Properties

Attribute Value
High-concerned chemical None
Charging Current 30A
Usage Scenario Power BMS, Energy Storage BMS
Certification CE
Balance Function Passive Balanced BMS
Type Hardware BMS
Charge and Discharge Port Common Port BMS
Battery Type LI-ION Battery BMS
Function Overcharge Protection, Over Discharge Protection

4.2. Lithium Iron Phosphate (LFP) Battery Specifications

Test conditions: room temperature 25°C. The voltage of each battery cell needs to be ≥ 3.25 V during testing.

Parameter Symbol Detailed Content Standard
Serial number S Number of battery strings 8S
Current A Current that the shield can withstand 30A/60A
Battery type - Ternary lithium / lithium iron phosphate lithium iron phosphate
Overcharge detection VDET1 Overcharge detection voltage 3.65V ± 0.035V
tVDET1 Overcharge detection delay time 1.3s (MAX)
Over-discharge detection VREL1 Overcharge relieve voltage 3.55V ± 0.025V
VDET2 Over discharge test voltage 2.350V ± 0.025V
tVDET2 Delay time for over discharge detection 1.5s (MAX)
Over discharge relieve voltage VREL2 Over discharge relieve voltage 2.55V ± 0.025V relieve
Discharge over-current detection voltage VDET3 Discharge over-current detection voltage 21mV ± 5mV
Discharge Over-current Protection IDP Instantaneous single pulse current (30A continuous) 200A
IDP Instantaneous multi-pulse current (30A continuous) 120A
- Duration 6-10s
Short-circuit Protection - Protection release condition Break short circuit
- Protection conditions External load circuit short circuit
TSHORT Detection delay time 300μS (MAX)
Internal Resistance RDS Main circuit on state resistance (battery voltage=3.4V) B- to P- RDS ≤ 1.2/0.8mΩ
Consume Current IDD Internal consumption of the circuit during operation MIN: 0.3μA MAX: 100μA
Battery Balance VBU Electricity balance detection voltage 3.45V ± 0.035V
tVBU Balance startup delay time 1.6S (MAX)
VBL Battery balance release voltage 3.44V ± 0.035V
IB 3.45V battery balance current 67mA ± 5mA
Over-temperature protection (Charging optional) - Low temperature -0°C ± 5°C (No)
MAX continuous working current (Charge) - Rated current of charger 30A/60A (Equivalent to A of the protective board)
MAX continuous working current (Discharge) - Rated current of battery pack 30A/60A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltage VDS Charging MOS MAX withstand voltage DC 42V

4.3. Ternary Lithium (NCM) Battery Specifications

Test conditions: room temperature 25°C. The voltage of each battery cell needs to be ≥ 3.6 V during testing.

Parameter Symbol Detailed Content Standard
Serial number S Number of battery strings 6S/7S/10S
Current A Max continuous current 30A/60A
Battery type - Ternary lithium / lithium iron phosphate Ternary lithium
Overcharge protection VDET1 Overcharge detection voltage 4.25V ± 0.035V
tVDET1 Overcharge detection delay time 1.3s (MAX)
Over-discharge protection VREL1 Overcharge relieve voltage 4.19V ± 0.025V
VDET2 Over discharge test voltage 2.8V ± 0.025V
tVDET2 Delay time for over discharge detection 1.5s (MAX)
Over discharge relieve voltage VREL2 Over discharge relieve voltage 3.0V ± 0.025V relieve
Discharge over-current detection voltage VDET3 Discharge over-current detection voltage 21mV ± 5mV
Discharge Over-current Protection IDP Instantaneous single pulse current (60A continuous) 400A
IDP Instantaneous multi-pulse current (60A continuous) 240A
- Duration 5-10s
Short-circuit Protection - Protection release condition Break short circuit
- Protection conditions External load circuit short circuit
TSHORT Detection delay time 300μS (MAX)
Internal Resistance RDS Main circuit on state resistance (battery voltage=3.4V) B- to P- RDS ≤ 1.2/0.8mΩ
Consume Current IDD Internal consumption of the circuit during operation MIN: 0.3μA MAX: 100μA
Battery Balance VBU Electricity balance detection voltage 4.2V ± 0.035V
tVBU Balance startup delay time 1.6S (MAX)
VBL Battery balance release voltage 4.19V ± 0.035V
IB 3.59V battery balance current 90mA ± 5mA
Over-temperature protection (Charging optional) - Low temperature -0°C ± 5°C (No)
MAX continuous working current (Charge) - Rated current of charger 30A/60A (Equivalent to A of the protective board)
MAX continuous working current (Discharge) - Rated current of battery pack 30A/60A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltage VDS Charging MOS MAX withstand voltage DC 42V

4.4. Dimensions

The length and width of the 6-10S series protection board are consistent, while the thickness varies based on the current rating.

Current Thickness (MM)
30A 5.5
60A 9
Diagram showing dimensions of a 6S 30A BMS board, 63mm x 48mm x 5.5mm

Dimensions of a 6S 30A 3.7V BMS board (63mm x 48mm x 5.5mm).

5. Setup: Wiring Diagram

Proper wiring is crucial for the safe and effective operation of the BMS. Always follow the diagrams carefully.

General Wiring Notes:

  1. Check the series sequence of batteries.
  2. Connect the wiring in strict accordance with the drawing and confirm that it is correct before inserting the balance board connector into the BMS.

6S Wiring Diagram (60A)

Wiring diagram for a 6S 60A 3.7V BMS, showing connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ with balance wires 1-6.

Wiring diagram for a 6S 60A 3.7V BMS. Note the connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ along with balance wires 1-6.

7S Wiring Diagram (60A)

Wiring diagram for a 7S 60A 3.7V BMS, showing connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ with balance wires 1-7.

Wiring diagram for a 7S 60A 3.7V BMS. Note the connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ along with balance wires 1-7.

10S Wiring Diagram (60A)

Wiring diagram for a 10S 60A 3.7V BMS, showing connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ with balance wires 1-10.

Wiring diagram for a 10S 60A 3.7V BMS. Note the connections for Battery-, P- (Charge/Discharge-), and Battery+/Charge/Discharge+ along with balance wires 1-10.

Product Accessories

Each BMS board typically comes with the necessary balance wires for connection to your battery pack.

Heltec BMS board with included balance wire harness

Heltec BMS board and included collection line (balance wires).

6. Operating: Protection Functions

The HT-610L Series BMS provides comprehensive protection for your battery pack. The table below details the protection thresholds for NCM and LFP battery types.

Type Overcharge single string detection voltage Overcharge single string release voltage Over-discharge single string detection voltage Over-discharge single string release voltage Single string balanced charging start
NCM 4.25V ± 0.035V 4.19V ± 0.025V 2.8V ± 0.025V 3.0V ± 0.025V 4.2V ± 0.035V
LFP 3.65V ± 0.035V 3.55V ± 0.025V 2.35V ± 0.025V 2.55V ± 0.025V 3.45V ± 0.035V

7. Maintenance

To ensure the longevity and optimal performance of your Heltec BMS, consider the following general maintenance guidelines:

  • Regularly inspect all wiring connections for tightness and corrosion. Loose connections can lead to poor performance or damage.
  • Keep the BMS board clean and free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Avoid exposing the BMS to extreme temperatures or humidity outside its operating range.
  • Ensure proper ventilation around the battery pack and BMS to prevent overheating.
  • If the BMS is removed or reinstalled, always double-check all connections against the wiring diagram before applying power.

8. Troubleshooting: Fault Handling

If you encounter issues with your BMS, refer to the following table for common fault phenomena, their causes, and recommended processing methods.

Fault Phenomenon Fault Inspection and Cause Processing Method
Can't discharge 1. Circuit not activated. 2. Battery cell voltage is lower than 3.0V±0.025V (NCM) / 2.35V±0.025V (LFP), triggering over-discharge protection. 1. Connect the circuit to activate the protection board for charging. 2. If battery is below 3.0V, charge to 3.6V (NCM) / 3.25V (LFP) and balance. Do not mix good batteries with poor ones.
Can't charge Battery cell voltage is higher than 4.215V (NCM) / 3.615V (LFP), triggering overcharge protection. Discharge battery to ~3.7V until balanced. Do not mix good batteries with poor ones.
Charging/discharge failure B-, B1, B2, B3... B+ Wrong wiring. Redraw the wiring or operate under the guidance of customer service.
Overcharge/discharge protection is invalid B-, B1, B2, B3... B+ Wrong wiring. Redraw the wiring or operate under the guidance of customer service.
Discharge protection Current value of load starting power supply exceeds the over-current protection current of the protection board. Replace the protection board with a larger current.
Components welded loosely A component has a pin not connected to the PCB pad. Repair the welding yourself.
Component welding (short circuit) Short circuit between two or more pins of the element. Remove the component and re-weld.
Electrostatic breakdown MOS tube not powered, forward and reverse resistance of any two pins of G, D, and S terminals are 0. Remove and replace the MOS tube yourself.

9. User Tips

  • Charging Voltage: Ensure your power supply is set to the correct voltage for your battery pack (e.g., 25.2V for a 6S pack) and not higher, as the BMS may not cut off charging at an overcharged individual cell voltage.
  • Balancing: The BMS provides passive balancing. While it does balance cells, the effectiveness of balancing (e.g., 83mA current) should be monitored, especially after initial recharges, to ensure all cells remain within tolerance.
  • Temperature Protection: The manual states temperature protection is optional. If you require this feature, inquire about compatible temperature probes and their connection points (e.g., RT1 and KO ports).
  • Parallel Use: If considering using multiple BMS boards in parallel, consult with technical support or experienced professionals to ensure compatibility and safe configuration.
  • Build Quality: Users generally find the boards well-designed and built, performing as expected for battery pack modifications in various applications like power tools.

10. Warranty & Support

Warranty Regulations

The warranty service period for this product is 1 year from the date of purchase.

Warranty Limitations:

  • The warranty is limited to normal use.
  • It does not cover man-made damage, damage from self-disassembly, modification, or repair not in accordance with instructions.
  • Damage caused by external force majeure factors is not covered.
  • Accessories such as test fixtures are considered consumables and are not covered by warranty.

Warranty Service Process:

  • If you require warranty service, please contact your dealer for processing.
  • If you cannot contact your dealer, you may contact Heltec directly via email or phone.
  • Currently, there are no after-sales service stations outside of China. For warranty service, you will need to send the product to Heltec for free repair. However, you will be responsible for the freight costs for the round trip.

Heltec guarantees that each product is shipped after being tested by professional protection board testing instruments. However, due to potential damage from static electricity and current during battery combination, and the nature of electronic components, it is normal to have defective products in use.

11. Manufacturing and Testing Process

Watch a short video showcasing the manufacturing and testing procedures for Heltec BMS boards.

Video: Manufacturing and testing process of Heltec BMS boards, including automated assembly and voltage/current/aging tests.

© 2024 Heltecbms. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.