SHIMANO MT200

Contents

Shimano BL-MT200 Hydraulic Disc Brake System User Manual

Models: BL-MT200, BL-MT201, BR-MT200, BR-M315

1. Important Safety Information

This manual is intended primarily for use by professional bicycle mechanics. Users not professionally trained for bicycle assembly should not attempt to install components themselves. If any part of the information is unclear, contact your place of purchase or a local bicycle dealer.

DANGER

Failure to follow instructions will result in death or serious injury.

WARNING

Failure to follow instructions could result in death or serious injury.

CAUTION

Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

  • Always use genuine Shimano parts. Loose or damaged parts can cause serious injury.
  • Wear safety glasses or goggles to protect your eyes during maintenance.
  • Products are not guaranteed against natural wear and deterioration from normal use and aging.
  • For maximum performance, use Shimano lubricants and maintenance products.

2. Setup and Installation

2.1. Product Overview

Shimano MT200 Hydraulic Disc Brake System Components

Description: An overview of the Shimano MT200 hydraulic disc brake system, showing the brake levers, calipers, hoses, and mounting hardware.

2.2. Brake Lever Installation

Secure the brake lever to the handlebar. Ensure it does not interfere with the shifting lever during operation.

  • Handlebar Diameter: All parts mounted on a flat handlebar are designed for a round section shape with a diameter of 22.2 mm (±0.2 mm).
  • Carbon Handlebars: Check the tightening torque recommended by the carbon handlebar manufacturer to avoid damage.
Brake Lever Installation Caliber

Description: Diagram showing the installation caliber of Ø22.2mm for the brake lever clamp and the brake travel adjust screw.

Brake Lever Tightening Torque
ModelHexagon Wrench SizeTorque
BL-MT200/BL-MT201/BL-MT401/BL-MT402-3A5 mm4 - 6 N·m

2.3. Disc Brake Rotor Installation

Install the disc brake rotor to the hub according to its type (Center Lock or 6-bolt).

Center Lock Type

Attach the disc brake rotor fixing lock ring and tighten it using the appropriate tool.

Center Lock Rotor Tightening Torque
ToolTorque
TL-LR15, TL-FC36, TL-LR1140 - 50 N·m

6-Bolt Type

Attach the disc brake rotor and the disc brake rotor tightening plate to the hub. Install and tighten the bolts in the specified order (1-6). Use new lock washers if applicable.

6-Bolt Rotor Tightening Torque
Bolt TypeTorque
Disc brake rotor fixing bolts2 - 4 N·m

2.4. Brake Hose Installation

Carefully cut the brake hose to the correct length using a utility knife or specialized tool. Pass the brake hose through the connecting bolt and olive, then attach it to the brake lever and caliper.

  • Ensure the hose is not twisted.
  • Apply premium grease to the threads of the connecting bolts.
Brake Hose Connecting Bolt Torque
ComponentWrench SizeTorque
Connecting bolt (lever end)8 mm5 - 7 N·m
Connecting bolt (caliper end, Banjo type)3 mm5 - 7 N·m
Connecting bolt (caliper end, Straight type)N/A5 - 7 N·m

2.5. Caliper Installation

Install the brake pads into the caliper, then mount the caliper to the frame/fork.

Brake Caliper Detail

Description: A close-up view of the brake caliper, showing the pads and piston area.

  • Install the pad fixing spring as shown in the illustration (L and R marks).
  • Pads with fins should be installed with fins at the front and back.
Caliper Mounting Torque
Mounting TypeTorque
International Standard Mounting (Adapter fixing bolt)6 - 8 N·m
Post Mounting (Caliper fixing bolt)6 - 8 N·m

After installation, operate the brake lever several times to check for normal operation and ensure no oil leaks.

3. Operation and Usage

3.1. General Brake Operation Warnings

  • Heat: Calipers and disc brake rotors become hot during operation. Do not touch them while riding or immediately after dismounting to avoid burns. Allow components to cool before adjustment.
  • Mineral Oil: Use only Shimano genuine mineral oil. Other types of oil can cause brake operation problems. Use oil from a freshly-opened container; do not reuse drained oil.
  • Air/Water: Be careful not to let water or air bubbles enter the brake system, as this can cause vapor lock.
  • Upside-Down Bicycle: Disc brakes are not designed to work when the bicycle is upside down. If the bicycle is turned upside down or on its side, the brake may not work correctly. Operate the brake lever a few times before riding to check normal operation.
  • Tandem Bicycles: Shimano disc brake systems are not compatible with tandem bicycles due to increased stress and potential for oil overheating, vapor lock, or hose rupture.
  • Fluid Leaks: If fluid leaks occur, immediately stop using the brakes and repair. Continuing to ride with leaks can cause sudden brake failure.

3.2. Bed-in Procedure for New Pads/Rotors

To optimize performance, perform the bed-in procedure after replacing brake pads or rotors:

  1. Ride in a flat, safe area. Depress one brake lever enough to allow pedaling. Do this with one brake lever at a time.
  2. With the brake lever depressed, ride for 20 meters.
  3. Repeat steps 1 and 2 at least 10 times for both front and rear brakes. The braking force will gradually increase.

4. Maintenance

4.1. Brake Pad Replacement

Replace brake pads if oil adheres to them, if they are worn down to 0.5 mm thickness, or if the pad presser springs interfere with the disc brake rotor.

  1. Remove the wheel from the frame.
  2. Remove the old brake pads.
  3. Clean the pistons and surrounding area.
  4. Use a flat-shaped tool to push the pistons straight back into the caliper. Be careful not to twist or damage the pistons.
  5. Install the new brake pads and the pad spacer (red). Ensure the snap ring is installed.
  6. Depress the brake lever several times until operation becomes stiff.
  7. Remove the pad spacer, install the wheel, and check for interference between the disc brake rotor and caliper.
Brake Pad Fixing Bolt Torque
ComponentWrench SizeTorque
Brake pad fixing bolt3 mm2 - 4 N·m

4.2. Piston Adjustment

If pistons operate incorrectly, protrude unevenly, or pads contact the rotor:

  1. Remove wheel and brake pads. Clean pistons.
  2. Push pistons straight back into caliper using a flat tool.
  3. Install brake pads and pad spacer (red).
  4. Depress brake lever fully several times to move pistons to initial positions.
  5. Remove pad spacer, install wheel, and adjust caliper mounting bolts if necessary to eliminate contact.

4.3. Lever Stroke Adjustment

Tighten the adjust bolt (clockwise) to increase stroke, loosen (counter-clockwise) to decrease stroke.

4.4. Free Stroke Adjustment

Loosening the free stroke adjustment screw increases the free stroke of the brake lever.

4.5. Mineral Oil Replacement and Bleeding

Replace mineral oil if it becomes severely discolored. Use only Shimano genuine mineral oil.

  1. Attach a tube with a bag to the bleed nipple. Open the bleed nipple to drain oil.
  2. Pour in fresh brake fluid.
  3. Bleeding Air: With the yellow spacer attached, place the bicycle in a stand. Set the brake lever at a 45° angle from the ground.
  4. Remove the upper bleed screw and O-ring, insert the oil funnel.
  5. Connect a syringe with oil to the bleed nipple. Push oil through until no air bubbles come out of the funnel.
  6. Temporarily close the bleed nipple.
  7. Connect a bag to the bleed nipple. Loosen the bleed nipple to allow oil and air bubbles to flow out naturally. Keep the funnel filled with oil.
  8. Once no more air bubbles come from the bleed nipple, close it.
  9. Depress the brake lever, then rapidly open and close the bleed nipple (0.5 seconds each time) 2-3 times to release air from calipers. Tighten the bleed nipple.
  10. Operate the brake lever until it becomes stiff.
  11. Tilt the lever unit 30° in both directions and operate the lever to check for remaining air.
  12. Plug the oil funnel with the oil stopper. Remove the funnel, attach the O-ring to the bleed screw, and tighten.
Bleed Nipple and Screw Torque
ComponentWrench SizeTorque
Bleed nipple7 mm4 - 6 N·m
Upper bleed screwN/A0.3 - 0.5 N·m

5. Troubleshooting

  • Noise during brake operation: Check brake pad thickness. If 0.5 mm or below, replace pads.
  • Sluggish brake operation: Gently depress the brake lever several times to allow air bubbles to return to the reservoir. If still sluggish, bleed the air from the brake system.
  • Fluid leaks: Stop riding immediately and repair.
  • Brakes not working after turning bicycle upside down: Operate the brake lever a few times to check for normal operation before riding.
  • Pistons not operating correctly: Follow the piston adjustment procedure in the Maintenance section.
  • Lever not stiff after bleeding: Repeat the bleeding procedure from step 5 (connecting bag to bleed nipple).

6. Specifications

Shimano BL-MT200 Hydraulic Disc Brake System
FeatureSpecification
Brand NameSHIMANO
Model NumberMT200
TypeHydraulic Disc Brake
Braking SystemHydraulic Disc Brake (Hydraulic Brake Pad)
OriginMainland China
High-concerned chemicalNone
Brake Lever3-finger Steel Lever
Oil Tank2mm inner hexagon
Caliper Piston2-piston
Rotor Compatibility160mm (standard)
Caliper Mounting Hole Distance74mm
Handlebar Clamp DiameterØ22.2mm
Product Size Diagram

Description: Diagram illustrating the caliper mounting hole distance of 74mm and compatibility with a 160mm brake rotor.

Brake Lever and Oil Tank Details

Description: Close-up of the brake lever showing the steel construction, the oil tank with a 2mm inner hexagon, and the 'SHIMANO MINERAL OIL BL-MT200' marking.

7. User Tips

  • Value for Money: Many users find the Shimano MT200 series to offer excellent performance for its price point.
  • Hose Length: When installing, carefully measure and cut the brake hoses to ensure a perfect fit for your bike setup.
  • Rotor Choice: The MT200 system is compatible with various Shimano rotors like G3 and HS1. Consult your dealer or Shimano's technical documents for specific differences and recommendations based on your riding style and conditions.

8. Warranty and Support

For the most up-to-date technical documents, manuals, and warranty information, please visit the official Shimano technical information website:

https://si.shimano.com

For service, support, or warranty claims, please contact your local Shimano distributor or authorized dealer.

© 2024 Shimano Corporation. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.