FGHGF AU-202

Contents

ABAC-AU-202 Stereo Mixer Audio Distributor User Manual

1. Introduction

The ABAC-AU-202 is a compact 2-input, 2-output stereo mixer and audio distributor designed for headphones and external power amplifiers. It allows you to combine two audio sources into a single output or distribute a single source to two outputs, with independent volume control for each channel.

ABAC-AU-202 Stereo Mixer

Figure 1: ABAC-AU-202 Stereo Mixer Audio Distributor

2. Safety & Warnings

Warning!

  • This product is only for adult use.
  • Please keep out of reach of children and pets to avoid accidental injury or ingestion.
  • Always check if the installation is correct before use.
  • If there is abnormal noise or equipment error after installation, stop using the device immediately.
  • Follow all instructions for proper use; misuse may cause harm.
  • Store the product in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Package Contents

Please check the package for the following items:

  • 1 x ABAC-AU-202 Stereo Mixer

4. Product Overview

The AU-202 features standard 3.5mm stereo jacks for all inputs and outputs, along with individual volume controls for each channel.

Front Panel

Front Panel of AU-202

Figure 2: Front Panel (Output Jack and Volume Controls)

  • OUT Jack: 3.5mm stereo output for headphones or an amplifier.
  • L/R Volume Knobs: Independent rotary controls for adjusting the volume of the left and right channels.

Rear Panel

Rear Panel of AU-202

Figure 3: Rear Panel (Input Jacks and Power Input)

  • IN Jacks (x2): Two 3.5mm stereo input jacks for connecting audio sources.
  • DC 5-20V Input: Power input jack for connecting the DC power adapter.

5. Setup

Follow these steps to set up your AU-202 mixer:

  1. Connect Audio Sources: Plug your audio source devices (e.g., smartphone, MP3 player, computer) into the IN jacks on the rear panel using 3.5mm stereo audio cables. You can connect one or two sources.
  2. Connect Output Devices: Plug your headphones or external amplifier into the OUT jack on the front panel using a 3.5mm stereo audio cable.
  3. Connect Power: Connect a DC power adapter (5-20V) to the DC 5-20V Input jack on the rear panel. Ensure the power source matches the specified voltage range.

6. Operating Instructions

Once set up, operate your AU-202 mixer as follows:

  1. Power On: The device will power on automatically once connected to a suitable DC power source.
  2. Adjust Volume: Use the L and R volume knobs on the front panel to adjust the output volume for the left and right channels independently.
  3. Mixing Audio: If two audio sources are connected to the IN jacks simultaneously, their audio will be mixed together and output through the OUT jack.
  4. Audio Distribution: The single output can drive two headphones or two amplifiers simultaneously.

7. Maintenance

  • Keep the device clean by wiping it with a soft, dry cloth.
  • Avoid using liquid cleaners or solvents.
  • Store the product in a dry and shady place, away from extreme temperatures and humidity.
  • Keep out of reach of children and pets.

8. Troubleshooting

  • No Sound Output:
    • Ensure the DC power adapter is correctly connected and providing power.
    • Check all 3.5mm audio cable connections at both the source and the mixer.
    • Verify that the audio source device is playing and its volume is turned up.
    • Ensure the L/R volume knobs on the AU-202 are not set to minimum.
  • Distorted or Poor Sound Quality:
    • Check the quality of your audio cables; try replacing them if necessary.
    • Ensure the audio source is not overdriving the input (e.g., very high volume from the source).
    • Verify that the power supply is within the DC 5-20V range and stable.
    • If using headphones, ensure their impedance is compatible (recommended < 32 Ohm).
  • Abnormal Noise or Equipment Error:
    • Immediately disconnect power and all audio connections.
    • Do not attempt to repair the device yourself. Contact support if available.

9. Specifications

FeatureSpecification
Product NameABAC-AU-202 Stereo Mixer Audio Distributor
Input Type3.5mm Stereo Jack (x2)
Output Type3.5mm Stereo Jack (x1)
Input Channels2
Output Channels2 (simultaneous output to two devices)
1st Stage OP AMPNJM4580
2nd Stage DriverNJM4556A
Working VoltageDC 5-20V
Recommended Headphone Impedance< 32 Ohm
Built-in BatteryNo
ColorBlack
MaterialMetal
Dimensions (L x W x H)6.5cm x 5.2cm x 2.4cm (2.55in x 2.04in x 0.94in)
Weight0.122 kg
OriginMainland China
AU-202 Dimensions Diagram

Figure 4: AU-202 Dimensional Diagram

10. User Tips

No specific user tips or common usage advice were available from customer reviews or Q&A for this product.

11. Warranty & Support

Specific warranty terms for this product are not detailed in this manual. Please refer to your point of purchase for warranty information.

Manufacturer Information:

Huizhou Tingli Technology Co., Ltd.
Room 001, Room C02, Floor 9, Elite, Building C, Jin Dian Garden, No.25, Taoziyuan, Qiaodong, Huizhou City Code: 516000

Email: yukn_oo_wwwddd@163.com
Phone: 8613651469669

EU Authorized Representative:

AC WORKS CONSULTING Srl
Via Vilfredo Pareto 125
Email: acworksltd@outlook.com
Phone: 0039 054729444

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.