1. Introduction
This manual provides instructions for the Scimagic-RC 433.92MHz Rolling Code Garage Remote Control. This remote is designed to be compatible with various SEAV gate and garage door opener systems, including SEAV BE HAPPY RS1, RS2, RS3 NEW, and SEAV BE SMART RS2, RS4 models. Please read these instructions carefully before attempting to program or use your new remote control.
2. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Scimagic-RC |
| Model Number | SEAV Garage remote control |
| Encoding Method | Rolling code |
| Frequency | 433.92MHz |
| Compatible List 1 | SEAV BE HAPPY RS1/RS2/RS3 NEW |
| Compatible List 2 | SEAV BE SMART RS2/RS4 gate control |
| Certification | CE |
| Origin | Mainland China |
| Dimensions (L x W x T) | 59mm x 32.5mm x 14mm |
| Weight | 0.03 kg |
3. Setup and Programming
Important: Programming requires direct access to your gate or garage door opener's receiver unit. This remote cannot be programmed by copying from an existing remote; it must be paired directly with the control unit.
Follow these steps to program your new Scimagic-RC remote control:
- Locate the Programming Button: Find the programming button inside your Prastel gate control enclosure. This button is typically on the receiver P.C.B. (Printed Circuit Board).
- Activate Programming Mode: Press the programming button briefly. An LED on the receiver P.C.B. will light up, indicating that the receiver is now in programming mode. You will have approximately 10 seconds to proceed with the next step.
- Program the New Transmitter: Take your new Scimagic-RC remote control. Press and hold the button you wish to use for operating your receiver for one second.
- Exit Programming Mode: After pressing the button on your new remote, wait approximately 30 seconds for the receiver to automatically exit programming mode.
- Test Operation: Programming is now complete. Your new remote control should now operate your receiver.
For visual guidance, please refer to the demonstration video below:
A detailed wiring diagram for the receiver board, showing components like the RF module, channel selection jumpers (CH1, CH2), and programming buttons (MEMO P, DEL P2), is typically found in the original receiver's manual. Ensure correct connections if you are installing a new receiver.
For additional information, you may consult the official user manual PDF: User manual (PDF).
4. Operation
Once programmed, your remote control is ready for use. The remote typically features multiple buttons, each capable of being programmed for a different function or gate/door. Press the corresponding button briefly to activate the desired function (e.g., open, close, stop).
5. Maintenance
5.1. Battery Replacement
If the remote control's range decreases or the LED indicator does not light up when a button is pressed, the battery may need to be replaced. The remote typically uses a standard coin cell battery (e.g., CR2032). To replace the battery:
- Carefully open the remote control casing.
- Remove the old battery.
- Insert a new battery of the same type, ensuring correct polarity.
- Close the casing securely.
5.2. Cleaning
Clean the remote control with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the casing or internal components.
6. Troubleshooting
- Remote not working after programming: Double-check that you have followed all programming steps precisely. Ensure you have direct access to the receiver unit and are pressing the correct programming button on the receiver. Verify that the remote's battery is functional.
- Limited range: Replace the battery. Ensure there are no obstructions between the remote control and the receiver. Large metal objects or walls can interfere with the signal.
- Remote cannot be cloned from another remote: This remote is a rolling code type and must be programmed directly to the receiver/control unit. It cannot be programmed by copying the signal from an already programmed remote.
7. User Tips
- Always ensure you have direct physical access to your gate or garage door opener's control unit before attempting to program a new remote.
- Keep the remote control away from extreme temperatures and moisture to prolong its lifespan.
8. Warranty and Support
This product is covered by a manufacturer's warranty against defects in materials and workmanship. Please retain your proof of purchase for warranty claims. For technical support or warranty inquiries, please contact the manufacturer directly.
9. Manufacturer Contact Information
Manufacturer: Shenzhen Scimagic Development Technology Co.Ltd
Address: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.