RunCam WiFiLink2 / WiFiLink2-G

Contents

RunCam Wireless WiFiLink2 / WiFiLink2-G Digital HD FPV Transmitter User Manual

For RC Drones with OpenIPC and 1080P FPV Camera

Introduction

This manual provides detailed instructions for the installation, operation, and troubleshooting of your RunCam Wireless WiFiLink2 or WiFiLink2-G Digital HD FPV Transmitter. Please read this manual thoroughly before using the product to ensure proper functionality and safety.

RunCam Wireless WiFiLink2 FPV Transmitter and Camera
Figure 1: RunCam Wireless WiFiLink2 FPV Transmitter and Camera

Setup

Product Features and Components

Familiarize yourself with the components of your WiFiLink2/WiFiLink2-G system:

Diagram of RunCam WiFiLink2 components
Figure 2: Product Features Diagram. Key components include Cooling Fan, M1.64 Screws, M1.68 Screws, Antenna, Antenna Plate, Fan Power Connector, CM1.2*2 Screws, 6Pin Connector, 26P Cable, RJ45 Port, M12 Lens, CNC Cover, and M2 mounting points.

Antenna Installation

When installing the WiFiLink2 on your aircraft, pay close attention to the following:

  • Antenna Layout: Ensure that the two tail antennas are fully spread apart to avoid entanglement and reduce signal interference.
  • Antenna Orientation: Point the antennas upward to avoid obstructions from the fuselage or battery, ensuring optimal signal performance.
Diagram showing proper antenna installation on an aircraft
Figure 3: Antenna Installation Diagram, illustrating optimal antenna placement for FPV systems.

6PIN Power Cable Connection

Connect the provided 6PIN power cable to the flight controller's DJI 6PIN interface. Refer to the diagram for correct pin assignments.

Wiring diagram for 6PIN power cable
Figure 4: 6PIN Power Cable Connection Diagram. Pinout: 9V, GND, RX, TX, NC, NC.

Follow these steps to update the firmware on your WiFiLink 2:

  1. Prepare Files: Copy WiFiLink-part0.bin and WiFiLink-part1.bin to the root directory of an empty SD card.
  2. Upgrade Steps:
    • Insert the prepared SD card into the camera mainboard and power it on.
    • The camera will enter upgrade mode (indicated by a green light flashing) for approximately 15 seconds.
    • The upgrade process takes about 1 minute. After completion, the green light will turn off, and the SD card will be cleared.
    • Upon re-powering, new configuration files (gs.key and user) will be generated automatically.

Card Flashing File Address: https://www.runcam.com/download/runcamwifilink2

How to Obtain Configuration Files

To generate initial configuration files:

  • Insert an empty SD card into the camera.
  • Power on the camera. It will automatically generate the necessary configuration files.

How to Set Parameters (Advanced)

It is recommended to use a text editor like Notepad++ to edit the user file. Only the parameters listed below can be modified:

Parameter Related Setting
ChannelCodec
Resolution RatioBitrate
MirrorFlip
RotateContrast
HueSaturation
Luminance...

Ethernet Port Default Settings

For direct connection via Ethernet, use the following default credentials:

Setting Value
IP Address192.168.1.10
Usernameroot
Password12345

Operating Instructions

LED Light Indications

The device uses LED lights to indicate its status:

Light Status Indication
Green OffAudio off
Green SolidAudio on
Green Fast FlashFirmware upgrade
Green Slow FlashRecording on
Blue SolidWiFiLink Startup
Blue Fast FlashWiFi Error
Blue & Green Alternating FlashHigh Temp Warning (>90°C)
Diagram showing LED light locations and colors
Figure 5: LED Light Status Diagram, indicating Blue, Green, and Red LED positions.

Install the PixelPilot APP

To use the FPV system, install the PixelPilot application:

Set APP Parameters

Within the PixelPilot APP, configure the following settings:

  • Set the Channel to 161.
  • Set the Video Codec to h265.
Screenshot of PixelPilot app showing Channel and Codec settings
Figure 6: PixelPilot App Parameter Setting Screenshot, highlighting Channel 161 and Codec h265.

How to Use with a PC Ground Station

To set up a PC Ground Station, follow these steps:

  1. Program Download: Download the necessary software from https://github.com/OpenIPC/fpv4win/releases.
  2. Step One (Driver Configuration):
    • Insert the 8812AU wireless adapter into your computer.
    • Reconfigure the driver using the Zadig program.
Screenshot of Zadig program for driver configuration
Figure 7: Zadig Driver Configuration Screenshot, showing the process for installing the 8812AU wireless adapter driver.
  1. Step Two (FPV4WIN Program):
    • Double-click the fpv4win program.
    • Select the network card, Channel, and Codec.
    • Click START to begin operation.
Screenshot of FPV4WIN program interface
Figure 8: FPV4WIN Program Screenshot, showing the interface for selecting network card, channel, and codec.

How to Use with Radxa ZERO 3W

For detailed guidance on using the WiFiLink2/WiFiLink2-G with Radxa ZERO 3W, please visit the technical support team:

Maintenance

To ensure the longevity and optimal performance of your RunCam WiFiLink2/WiFiLink2-G, consider the following maintenance tips:

  • Regularly check all cable connections for secure fit and signs of wear.
  • Keep the device clean and free from dust and debris, especially the cooling fan.
  • Periodically check the official RunCam website for firmware updates to ensure you have the latest features and bug fixes.
  • Store the device in a dry, cool environment when not in use.

Troubleshooting

What to Do if There Is No Display

If you are experiencing no video display, check the following:

  • Verify that the power supply to the device is normal and stable.
  • Ensure that the Channel and Codec settings in your application (e.g., PixelPilot or fpv4win) are correctly configured (e.g., Channel 161, Codec h265).

What to Do if FC OSD Information Is Missing

If your Flight Controller (FC) On-Screen Display (OSD) information is not appearing, perform these checks:

  1. Check Configuration:

    Verify that the configuration settings are correct. The three critical parameters should be:

    • SERIALS_BAUD: 115 (corresponding to 115200)
    • SERIALS_OPTIONS: 0
    • SERIALS_PROTOCOL: 1 or 2 (corresponding to Mavlink1 or Mavlink2)
  2. Check the Serial Port:

    Confirm that the FC serial port data is normal and available. Ensure the wiring is correct, specifically that TX and RX lines are cross-connected between the WiFiLink2 and the flight controller.

Screenshot of FC OSD configuration settings
Figure 9: FC OSD Configuration Screenshot, showing parameters like SERIALS_BAUD, SERIALS_OPTIONS, and SERIALS_PROTOCOL.

Specifications

Feature Specification
ModelWiFiLink 2
SensorIMX415
FOV160°
Resolution1080P@60FPS/1080P@90FPS/720P@120FPS
Power Supply9-22V (Max 15W)
Lens Module19*19mm/M12 Lens/MIPI Cable 130mm
Hole Distance25.5*25.5mm
PCB Size30.6mm*33mm
Weight30g (with fan) / 25g (without fan)
Antenna2dB/IPEX1 (5G)
Power5.8 GHz: ≤29dBm (FCC), ≤20dBm (CE)

Power Value Reference Table

Values 20 25 30 35 40 45 50 55 58
dBm1620222426272828.529
mW40100160250400500630700800

*The default power value is 20.

User Tips

Based on common user inquiries and experiences, here are some helpful tips:

  • Check Package Contents: Always verify that all expected components, such as the network card and antennas, are included in your package upon arrival.
  • Cable Length: Be aware of the MIPI cable length (130mm) when planning your drone build to ensure proper routing and reach.
  • Goggle Compatibility: Before purchasing, confirm the compatibility of your VRX receiver and FPV goggles with the WiFiLink2/WiFiLink2-G system to ensure a seamless experience.

Warranty and Support

For further assistance, technical support, or warranty information, please refer to the official resources:

  • A comprehensive user manual in PDF format is available for download: User Manual (PDF).
  • For technical support, you can contact the RunCam support team via their help center: RunCam Support.

Compliance Statement

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.