GGBEE Human Sensor Lamp

Contents

GGBEE Motion Sensor LED Cabinet Light User Manual

Model: Human Sensor Lamp

Product Overview

The GGBEE Motion Sensor LED Cabinet Light is a versatile, rechargeable lighting solution designed for various indoor applications. It features infrared induction for automatic lighting, offering both sensor and always-on modes. Available in multiple lengths (10cm, 20cm, 30cm, 50cm) and light temperatures (cold white, warm white), it provides bright, soft, and non-blinding illumination.

GGBEE Motion Sensor LED Cabinet Light in a bedroom setting, showing white and warm light options.

Figure 1: Product overview showing the light bar in a bedroom setting with options for white and warm light.

Video 1: Product demonstration showcasing features, modes, and magnetic installation.

Setup and Installation

Initial Charging

Upon receiving your light, it may have a low battery charge from factory testing. For optimal performance, fully charge the device before first use. The initial charge typically takes 2-4 hours.

  1. Connect the provided USB cable to the Type-C charging port on the lamp holder.
  2. Plug the other end of the USB cable into a DC5V power source (e.g., a USB wall adapter, computer USB port).
  3. The signal indicator light will turn red during charging and green when fully charged.

Component Identification

Detailed view of the light bar's components: Type-c Socket, Signal Indicator Light, Switching Mode button, PC Translucent Panel, and Sensing Area.

Figure 2: Detailed view of the light bar's components and controls.

  • Type-c Socket: For charging the device.
  • Signal Indicator Light: Shows charging status (red for charging, green for full) and mode changes.
  • Switching Mode Button: Used to cycle through operating modes and adjust brightness.
  • PC Translucent Panel: Diffuses light for a soft glow.
  • Sensing Area: The infrared sensor that detects motion.

Mounting the Light

The light bar features a simple magnetic installation, allowing for easy attachment and removal.

  1. Identify a clean, flat surface where you wish to install the light.
  2. Peel the adhesive backing from the included magnetic strips.
  3. Attach the magnetic strips to your desired surface.
  4. Align the light bar with the magnetic strips on the surface. The light bar will magnetically attach.
  5. The light can be easily removed from the magnetic strips for charging or repositioning.
Image demonstrating the simple magnetic installation of the light bar.

Figure 3: Simple magnetic installation process.

Operating Instructions

Switching Modes

Use the Switching Mode button to cycle through the available operating modes:

  1. Press the switch once: The light will turn on in Constant On Mode (always-on).
  2. Press the switch again: The light will flash twice to activate the Night Sensing Mode. In this mode, the light will only activate when motion is detected in dim conditions.
  3. Press the switch a third time: The light will flash four times to activate the Day Night Sensing Mode. In this mode, the light will activate when motion is detected regardless of ambient light conditions.
  4. Press the switch a fourth time: To turn the light off.

Adjusting Brightness

When the light is on in any mode, long press the Switching Mode button to adjust the brightness level. Release the button when the desired brightness is reached.

Sensing Functionality

Diagram explaining Sensor Mode (auto-sensing, light up when people come, off after 25s) and Normal Mode (always-on via pushbutton switch).

Figure 4: Explanation of Sensor Mode and Normal Mode.

  • Sensor Modes (Night Sensing / Day Night Sensing): The light will automatically turn on when motion is detected within the sensing range. It will turn off approximately 25 seconds after no motion is detected.
  • Constant On Mode: The light remains continuously on until manually switched off or the battery depletes.
Image highlighting the '0 Seconds Sensing' feature, where lights turn on instantly when motion is detected.

Figure 5: The light features instant activation upon motion detection.

Maintenance

Battery Care

Proper battery maintenance ensures optimal performance and longevity of your LED light.

  • Charging Recommendations: Always use a charger with a rated voltage of DC5V and a current of 2 amps or less. Avoid using fast charging, as this can negatively impact battery life.
  • Regular Charging: When the light output becomes dim, recharge the battery promptly.
  • Monthly Charge: To preserve battery health, charge the device at least once a month, even if it has not been used extensively.
  • Full Cycles: For the first 10 charge cycles, it is recommended to fully discharge and then fully recharge the battery.
  • Prompt Recharging: After the battery is depleted, recharge it as soon as possible. Leaving the battery discharged for extended periods can shorten its lifespan.

Cleaning

To clean the light bar, gently wipe it with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water.

Troubleshooting

  • Light not turning on: Ensure the device is fully charged. Check the selected operating mode (Constant On, Night Sensing, Day Night Sensing) and ensure it's appropriate for the ambient light conditions if in a sensor mode.
  • Sensor not detecting motion: Verify the light is in a sensor mode. Ensure the sensing area is not obstructed.
  • Light flickering or dim: This usually indicates a low battery. Recharge the device fully.
  • Light not turning off in sensor mode: Ensure there is no continuous motion within the sensing range. The light will turn off approximately 25 seconds after the last detected motion.

Specifications

FeatureSpecification
Brand NameGGBEE
Model NumberHuman Sensor Lamp
Light SourceLED bulbs
Is Bulbs IncludedNo (integrated LEDs)
Power SourceDC, Rechargeable Battery
Voltage0-5V, 5V
Wattage1W
Luminous Flux<60 Lumens
Is DimmableNo (brightness adjustable)
Body MaterialABS
Installation MethodSelf-contained (magnetic attachment)
FeaturesMotion sensor, Auto-sensing, Portability, Night-light, Reading Lamp
Item TypeBar Lights
UseIndoor Lighting
CertificationCE
OriginMainland China
Dimensions (approx.)Length: 10cm, 20cm, 30cm, 50cm (various models); Width: 2cm; Height: 2cm
Package Weight (approx.)0.096 kg

User Tips

  • To maximize battery life, utilize the sensor modes when continuous light is not required.
  • The sensor performs best when unobstructed and within its intended range.
  • Consider the light temperature (cold white or warm white) based on your room's ambiance and personal preference.

Warranty and Support

The internal rechargeable battery in this lamp is non-replaceable. Once the battery reaches the end of its service life, the lamp will no longer be functional.

For any product inquiries, technical support, or issues not covered in this manual, please contact the seller directly through your purchase platform.

For additional information, you may refer to the original user manual PDF: View User Manual (PDF)

© 2024 GGBEE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.