Heltecbms LTO 6S Balance Board

Contents

User Manual

Heltecbms 2.7V/16V LTO 6S Balance Board Equalization Circuit

Model: LTO 6S Balance Board

1. Introduction

This Heltecbms protection board is designed to balance and protect 2.7V Lithium Titanate (LTO) batteries and 2.7V Super Farad Capacitors in a 6-series (6S) configuration, supporting a total voltage of up to 16V. It features an equalization circuit that actively discharges cells/capacitors when their voltage exceeds a set equalization voltage, dissipating excess power through a power resistor. The circuit maintains a voltage equalization accuracy of ±1%.

The protection voltage can be finely adjusted within the range of 2.5V to 3V by replacing the voltage divider resistor. For higher equalization voltages, a resistor with higher resistance is required.

For additional documentation, a user manual in PDF format is available. Please refer to the seller's product page for the direct download link.

2. Specifications

Product feature overview showing 1-6S, 2.7V balance voltage, and 0.7A/60uA balance/quiescent current.

Figure 1: Key Features of the LTO 6S Balance Board

Table 1: Product Parameters
Parameter Value
Type LTO Battery / Super Capacitor
Balanced Mode Passive Balance
Balanced Voltage 2.7V
Balanced Current 0.7A
Quiescent Current 60uA
Charge Current NO Limit
Discharge Current NO Limit
Product Size 46 * 76mm

Package Dimensions:

  • Length: 11 cm
  • Width: 15 cm
  • Height: 2 cm
  • Weight: 0.035 kg

3. Setup and Wiring

When connecting the balance board, always pay attention to the polarity of the battery cells. Connect the wires from the negative terminal to the positive terminal in sequence.

3.1 Pre-wiring Instructions

  • For Farad Capacitors: Before wiring, ensure all charges stored in the capacitors are drained. Short-circuit the positive and negative terminals of each capacitor with a wire for more than three minutes (the larger the capacity, the longer the short-circuiting time required to fully discharge).
  • For Lithium Titanate Batteries: Ensure good battery consistency before assembly. The internal resistance/capacity of each battery should not vary significantly. If possible, test and select batteries with good consistency to form the battery pack to maximize its lifespan.

3.2 Wiring Diagram

Refer to the diagram below for correct wiring. The first line labeled "-" on the protection board should be connected to the negative pole of the first battery. Subsequent lines connect to the positive pole of each cell in sequence. The last line connects to the positive pole of the entire battery pack.

Wiring diagram for connecting the balance board to a 6S battery pack.

Figure 2: Product Connection Diagram

Close-up of the balance board's wiring terminals.

Figure 3: Balance Board Terminal Layout

Diagram showing the connection of load and charging to the balance board.

Figure 4: Connecting Load and Charging

3.3 Cascading Multiple Boards

Multiple protective plates can be connected in series for larger battery packs. To cascade, connect the seventh line of the first protective plate and the first line of the second protective plate to the connection piece of the sixth battery and the seventh battery together. This allows for protection of up to 12 series of batteries or capacitors.

Diagram illustrating how to cascade multiple balance boards for more cells.

Figure 5: Support Cascading Diagram

4. Operating Instructions

4.1 Charge / Discharge Matters

There are differences in precautions for lithium titanate batteries and Farad capacitors during charging and discharging:

  • Rafa Capacitor: Before use, charge the capacitor group to a voltage similar to the working state. Use a high-power resistor to limit the current to prevent excessive current from damaging the power supply.
  • LTO Battery:
    • Charging Voltage: The number of battery strings is N, and the voltage limit for each cell is 2.7V. The maximum charging voltage should not exceed N * 2.7V. If the charger voltage is too high, all indicator lights will turn on, indicating you should stop charging.
    • Charging Current: This is determined by the charger and the battery performance, and has no relation to the protection board used.
    • First Charge: Before charging, ensure the voltage difference between each battery is within 0.05V. The higher battery needs to be discharged to the same level. Pay attention to the status of the protection board at all times during the first charge! When the voltage of a single cell reaches around 2.7V, the overpressure indicator light will turn on. At this time, pay special attention to the voltage of the corresponding battery.
Diagram illustrating charge and discharge considerations for Rafa Capacitors and LTO Batteries.

Figure 6: Charge/Discharge Considerations

4.2 Adjusting the Balanced Voltage

The protection voltage can be adjusted within the range of 2.5V to 3V by replacing the voltage divider resistors. For a higher balanced voltage, a resistor with a higher resistance value needs to be replaced.

The two voltage divider resistors in the circuit are shown in the figure below. They are two 1% precision 0603 surface-mount resistors. By modifying the silk-screened 18K resistor on the PCB, the equilibrium voltage can be changed.

Diagram showing how to adjust the balanced voltage by replacing resistors.

Figure 7: Adjusting Balanced Voltage

4.3 Voltage Divider Resistor Reference

If you need to change the protection voltage, refer to the website www.elecfans.com/tools/dianzufenya.html. Enter the required voltage in the input field. For other parameters, follow the instructions in the picture and calculate the resistance value in kiloohms (the maximum cannot exceed 50 kiloohms; otherwise, the parallel resistor Rb should be modified to 110 kiloohms).

There are 2 resistors per channel, and a total of 6 channels make up 12 resistors. The resistors marked as 18K on the board are in series. Generally, only this resistor needs to be changed.

Table 2: Reference Voltage - Resistance Value
Reference Voltage Resistance Value
2.5V 0 ohm
2.6V 1 kiloohm
2.65V 13 kiloohms
2.7V 18 kiloohms
2.75V 22 kiloohms
2.8V 27 kiloohms
Diagram highlighting indicator lights and voltage divider resistors on the board.

Figure 8: Voltage Divider Resistor Location

4.4 Adding High-Power Resistors (Advanced Operation)

The protection voltage can be adjusted within the range of 2.5V to 3V by replacing the voltage divider resistors. For a higher balanced voltage, a resistor with a higher resistance value needs to be replaced.

The holes for the added plug-in resistors (hole package axial-0.5, pad hole diameter 0.85mm, hole spacing 12.7mm) are applicable to 1W plug-in resistors. This can increase the balanced current by paralleling power resistors.

  • For 1W color-coded resistors, the recommended resistance value is around 6 ohms.
  • For 2W color-coded resistors, it is around 3 ohms.

The color-coded resistors should be kept at a certain distance from the surface mount resistors to ensure proper heat dissipation.

Diagram showing where to add high-power resistors to the balance board.

Figure 9: Adding High-Power Resistors

5. Troubleshooting (Q&A)

Q&A section from the product description.

Figure 10: Common Questions and Answers

  1. What is the maximum voltage and balanced current this protection plate can handle? What is the charging and discharging voltage and current values of the protection board?

    This protection board is suitable for 2.7V lithium titanate batteries and 2.7V Rafah capacitors. The balanced current is approximately 0.7A. The default protection voltage is 2.7V, and it can be changed to a minimum of 2.5V. The maximum recommended value is no more than 3V. The charging and discharging of the capacitor/battery pack does not directly pass through the protection board, so there is no limit on the charging current. The charging voltage is determined by the number of series connections, and the maximum charging voltage should not exceed (number of series connections * 2.7V).

  2. How many battery/capacitor strings can this protective board be used for?

    The single protection board is suitable for 1 to 6 strings of batteries/capacitors. When the number of strings is less than 6, the wiring starts from the negative terminal and the extra wires can be left unused. Multiple protection boards connected in series can protect a greater number of series (for example, 2 protection boards connected in series can protect a maximum of 12 series of batteries or capacitors).

  3. Does the protection board have under-voltage protection? Are there any indicator lights?

    There is only limited overvoltage protection, but no undervoltage protection. There are indicator lights that show the working status of the protection board. When the voltage of a single cell exceeds 2.7V, the corresponding indicator light will turn on, and the corresponding discharge circuit will start discharging. When the voltage of the corresponding single cell drops below 2.7V, the indicator light will go out, and the circuit will stop discharging.

  4. Does this protective plate have the function of balancing the voltage?

    The protection board is of passive balancing. The discharge circuit will only activate when the voltage exceeds the protection voltage. Therefore, if you want to balance the voltage, you need to set the charging voltage slightly higher than the protection voltage to activate the balancing. This is a manual operation for capacitors/battery packs with excessive voltage differences. If the pressure difference is not significant, there is no need to perform it.

    For example: For a 6-string 2.7V capacitor group, set the charging voltage to 16.5V (slightly higher than the total protection voltage of 16.2V by about 0.3V is sufficient), set the charging current to 0.5A (not exceeding 0.5A), and continue charging for 2-4 hours after it is fully charged.

6. User Tips

  • Always ensure proper polarity during wiring to prevent damage to the board and battery/capacitor pack.
  • For optimal performance and longevity, use battery cells or capacitors with good consistency in internal resistance and capacity.
  • When adjusting the balanced voltage, make small, incremental changes and monitor the cell voltages carefully.
  • If using Farad capacitors, always fully discharge them before connecting to the balance board.
  • During the first charge of an LTO battery pack, closely monitor individual cell voltages, especially when indicator lights turn on, to prevent overcharging.
  • For packs with significant voltage differences, a manual balancing process (charging slightly above protection voltage with limited current) may be necessary to achieve initial balance.

7. Warranty and Support

For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the HeltecPower Store directly through the platform where the product was purchased. Provide your order details and a clear description of the issue for prompt support.

8. Manufacturing Process

The Heltecbms balance boards are produced in a modern factory environment, utilizing advanced manufacturing techniques to ensure product quality and reliability. The following video provides a glimpse into the production process:

Video 1: Heltec BMS Factory Production Overview

Image showing the Heltec BMS factory production line with workers and machinery.

Figure 11: Heltec BMS Production Line

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.