1. Introduction
The IKSLED Mirror Touch Switch is an intelligent capacitive touch control device designed for LED-illuminated mirrors. It allows for easy control of single or dual-color LED lights, offering on/off functionality and stepless dimming. The switch features a discreet LED indicator that changes color to show its status (red for off, blue for on).
This manual provides detailed instructions for the safe installation, operation, and maintenance of your mirror touch switch.
2. Safety Information
WARNING: Please strictly follow these instructions and safety tips. Use the product with caution.
- This switch is suitable for DC constant voltage power supply only. Do NOT use a constant current power supply to drive the switch, as this may burn out the unit.
- Ensure no metal material is in direct contact with the switch module, especially on the back of the mirror, as this can interfere with its operation.
- The coating on the back of the mirror where the sensor is placed must be scraped off to ensure proper touch detection.
- Avoid splashing water directly onto the switch module. Water ingress can cause malfunctions or damage.
- Installation should be performed by a qualified professional if you are unsure about electrical wiring.
3. Product Overview
The IKSLED Mirror Touch Switch integrates seamlessly into your mirror design, providing a clean and modern control interface for your LED lighting. It is designed for mirrors or transparent glass with a thickness of up to 6mm.
Key Features:
- Capacitive Touch Control: Easy and intuitive operation.
- On/Off Functionality: A quick touch turns the light on or off.
- Stepless Dimming: Long press to adjust brightness from 10% to 100%.
- LED Indicator: Background light on the touch switch board (red for off, blue for on) for easy visibility in the dark.
- Compatibility: Suitable for single-color and dual-color LED strips.
Product Demonstration Video:
Video demonstrating the operation of the IKSLED Mirror Touch Switch, including color temperature adjustment and dimming for dual-color LED strips.
4. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Mirror Touch Switch |
| Model Number | mirror touch switch |
| High Voltage Model Input/Output | 100V-240V input / 12V output 1A |
| Low Voltage Model Input | DC 3V, 3.7V, 5V, 12V, 24V |
| Current | 5A |
| Penetration Thickness | Mirror/transparent glass within 6mm |
| Material | Plastic |
| Certification | CCC, CE |
| Warranty | 1 year |
| Dimensions (approx.) | 50mm x 47.5mm x 10mm (L x W x H) |
Note: Specifications may vary slightly between different models (single color, dual color, USB, DC, leadwire).
5. Setup and Installation
Follow these steps carefully to install your IKSLED Mirror Touch Switch:
- Prepare the Mirror:
- Identify the desired location for the touch sensor on the mirror surface.
- On the back of the mirror, directly behind the chosen location, mark the center of the touch area (e.g., with a "+" sign).
- Carefully scrape off the reflective coating on the back of the mirror in the marked area. This is crucial for the touch sensor to function correctly. The logo diameter for the touch area is typically 17-20mm.
Figure 1: Visual guide for installation steps, including marking and scraping the mirror coating. - Mount the Switch:
- Tear off the double-sided adhesive tape from the back of the touch switch module.
- Carefully stick the sensor module directly onto the scraped area on the back of the mirror, ensuring it is centered with your marked touch area.
- Connect the LED Light:
- Connect the output wires from the touch switch to your LED light strip. Ensure correct polarity (positive to positive, negative to negative).
- For dual-color LED strips, connect the corresponding wires (e.g., V+, V-, and color control wires) as shown in the diagrams.
Figure 2: Wiring for a dual-color LED strip. Connect V+ and V- from the switch to the LED strip.
Figure 3: DC input and output ports for the dual color model, typically 14cm wire length.
Figure 4: USB input and output for the single color model, with 30cm input and 15cm output wires. - Connect Power Supply:
- Connect the input wires of the touch switch to a compatible DC constant voltage power supply (e.g., 3V, 3.7V, 5V, 12V, or 24V depending on your model).
- Ensure the power supply is a constant voltage type. Using a constant current LED driver will damage the switch.
Figure 5: Important distinction between compatible (constant voltage) and incompatible (constant current) power supplies. - Power On:
- Once all connections are secure, turn on the main power switch to activate the mirror touch switch. The background light on the touch area should illuminate.
6. Operation
The IKSLED Mirror Touch Switch offers simple and intuitive control over your mirror's LED lighting:
- Turn On/Off: A quick, short touch on the designated touch area will toggle the LED light on or off.
- Stepless Dimming: When the light is on, press and hold your finger on the touch area to activate stepless dimming. The brightness will gradually increase or decrease. Release your finger when the desired brightness level is reached.
- LED Indicator: The touch switch board has a background light. When the light is off, the indicator will typically be red. When the light is on, it will turn blue. This helps locate the switch in low light conditions.
7. Maintenance
- Keep the mirror surface and the area around the touch sensor clean and dry.
- To clean, use a soft, damp cloth. Avoid abrasive cleaners or excessive moisture near the switch module.
- Regularly check wiring connections to ensure they remain secure.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch not responding to touch |
|
|
| LED light does not turn on |
|
|
| Switch burned out |
|
|
9. User Tips
- Check Package Contents: Always verify if the light strip is included with your purchase or if it needs to be acquired separately, as the switch is often sold as a standalone component.
- Mirror Preparation is Key: Ensure the reflective coating on the back of the mirror is thoroughly removed in the sensor area. Incomplete removal is a common cause of unresponsive touch functionality.
- Optimal Placement: Consider placing the touch sensor in an easily accessible yet discreet location on your mirror for the best user experience.
10. Warranty and Support
This IKSLED Mirror Touch Switch comes with a 1-year warranty from the date of purchase, covering manufacturing defects under normal use.
For further assistance, detailed diagrams, or additional product information, please refer to the official user manual PDF:
You may also contact your retailer or the manufacturer's customer support for technical inquiries.