1. Introduction
Welcome to your new FUERS G12 Smart Security System. This manual provides detailed instructions for setting up, operating, and maintaining your alarm system to ensure optimal performance and security for your home or business.

Figure 1: Overview of the FUERS G12 Smart Security System components including the main hub, cameras, siren, various sensors, remote controls, and RFID tags.
2. Important Notes Before Getting Started
This guide is applicable for both Hub cellular models (2G/4G) and Hub cellular + Wi-Fi models (2G+Wi-Fi/4G+Wi-Fi).
2.1. Conditions for Successful Setup
- SIM Card: If using a 4G SIM card, ensure your wireless service provider's 2G network is still available in your country. If not, purchase the hub with a 4G cellular communicator.
2.2. For Hub Cellular + Wi-Fi Models Only
- Wi-Fi Network: Select a 2.4GHz Wi-Fi network. The hub does not support 5GHz Wi-Fi. Selecting the 5GHz band is a common setup mistake.
- Wi-Fi Password: Must not contain spaces or special characters.
- Hub Placement: Place the hub as close as possible to your router during setup.
- Network Speed: A slow network speed affects performance. An upload speed of at least 2Mbps or faster is recommended.
- AP Isolation: Ensure the AP isolation setting in your router is disabled.
2.3. What You Need
To set up and use your Alarm System, you will need:
- An iPhone or Android phone.
- The Smart Security System app.
- An unused indoor power outlet.
- A micro SIM card supporting 2G/GSM (for 2G version) or 4G network (for 4G version).
- A Wi-Fi 802.11 b/g/n (2.4GHz) network connection (for Hub cellular + Wi-Fi models only).
3. System Components Overview
Your FUERS G12 system includes the following main components:
3.1. Smart Hub (Panel)
The central unit with alarm, display, and keypad. It is the brain of the system.
Smart Hub Overview:
- Display Window: Shows system status, time, alarm information, menus.
- Keypad: ARM, ARM STAY, DISARM, and DIAL buttons for passcode entry and settings.
- RFID Tag Reader Zone: Tap RFID tags here to arm/disarm.
- Status Indicator: Indicates ARM/DISARM/ARM STAY/ALARM status.
- Tamper Switch: Triggers an alarm if the hub is removed from its bracket.
- Microphone: For monitoring and two-way talking.
- Backup Battery ON/OFF: Switch to activate the built-in backup battery.
- Regular SIM Card Slot: For inserting the SIM card.
- Power Port (Micro USB): For connecting the power cable.
3.2. PIR Motion Detector
Senses movement in its detection area. Typically set to 'Out Arm Active Mode'.
PIR Motion Detector Features:
- LED Indicator: Blinks on power-on, on motion detection, and for low battery.
- Pairing Button: Sends a transmission signal for pairing.
- Setting Jumpers: For pulse counter (1, 3, or 5 pulses) and working mode (TEST/NORMAL).
- Battery Receptacle: Holds three AA 1.5V batteries.
3.3. Door/Window Sensor
Detects when a door or window is opened. Set to 'Stay Arm Active Mode' by default.
Door/Window Sensor Features:
- LED Indicator: Lights up when opened, blinks for low battery.
- Setting/Panic Button: Sends transmission signal for pairing or alarm.
- Open-close Magnet: Works with the sensor to detect open/close state.
- Tamper Switch: Triggers notification if the sensor is tampered with.
- Battery Receptacle: Contains one CR2032 3V lithium battery.
3.4. Remote Tag (Wireless Key)
Used for quick arming, disarming, and triggering emergency alarms.
- Arm Button: For away-arm.
- Stay Arm Button: For home-arm.
- Disarm Button: To disarm the system.
- SOS Button: For emergency alarms.
3.5. RFID Tag
Allows arming or disarming without entering a password by tapping on the hub.
3.6. Wireless Siren (Optional)
Sounds when the alarm goes off.
3.7. Accessories
Power Adapter, Hub Bracket, Bottom Cover, Screws, Extra Adhesive Mounting Strips.

Figure 2: Example of a FUERS G12 Alarm Kit (Kit 1) showing the main hub, wireless siren, PIR motion detector, door/window sensor, remote controls, and RFID tags.
4. Setup and Installation
4.1. Smart Hub Placement
- Place the hub close to an entry/exit point for easy access.
- Ensure good Wi-Fi and cellular signal strength.
- Use an unswitched wall outlet to prevent accidental power loss.
4.2. Door/Window Sensor Placement
- Align the magnet with the middle of the sensor.
- Place the magnet within 0.6 inches (1.5cm) of the sensor when the door/window is closed.
4.3. PIR Motion Detector Installation
- Mounting Height: 79 to 87 inches (2 to 2.2m) above the floor.
- Mount the bracket with screws, then place the detector.
- Detection Area: The detector has a 110° detection scope.
- Special Considerations:
- Do not install outdoors, in garages, or on glass.
- Cannot detect motion through glass.
- Avoid places where it can get wet.
- Keep at least 3 feet (1 meter) away from heat sources.
- Do not obstruct with large appliances or furniture.
4.4. Installing the SIM Card
A regular SIM card is required for cellular services. Ensure the SIM card is inserted when the hub is off and its security code is deactivated.
4.5. Setting Phone Numbers for SMS and Calls
Up to 5 phone numbers can be stored to receive SMS and calls during alarms. The hub calls numbers successively (up to 2 rounds). Two-way talk connects automatically when a stored number calls the hub.
To set numbers: Go to Menu > Phone > 1st Phone/2nd Phone/...
- Use scroll buttons to navigate, tap to enable keypad.
- Enter the phone number (up to 18 digits), tap to confirm.
- Toggle 'on'/'off' for Alarm Call and Alarm Text Message.
- Press to save settings.
4.6. Pairing Sensors and Remote Tags
The system can connect up to 100 wireless sensors, 10 remote tags, and 10 RFID tags.
4.6.1. Pairing a Remote Tag
Go to Menu > Parts > Remote > Add.
- Enter a unique digit (0-9) for the tag.
- When "Synchronizing" is shown, press any button on the remote tag.
- "Learning OK" will confirm successful pairing.
4.6.2. Pairing a Wireless Sensor (Door/Window or PIR)
Go to Menu > Parts > Detector > Add.
- Select desired Zone Name and Zone Mode (Normal, 24H, Delay, Home, 24H mute, Doorbell).
- Enter a unique Zone Number (0-89).
- When "Synchronizing" is shown, trigger the wireless sensor (e.g., separate magnet for door sensor, walk in front of PIR).
- "Learning OK" will confirm successful pairing.
4.6.3. Pairing an RFID Tag
Go to Menu > Parts > RFID > Add.
- Enter a unique digit (0-9) for the tag.
- When "Synchronizing" is shown, tap the RFID Tag on the RFID read zone of the panel.
- "Learning OK" will confirm successful pairing.
4.6.4. Pairing a Wireless Siren
Go to Menu > Parts > Siren Learn.
- Press and hold the SET button on the siren until two beeps are heard and the light ring blinks.
- Press the button on the panel within 6 seconds.
- Four beeps from the siren indicate success.
4.6.5. Pairing an Alarm Wireless Switch
Go to Menu > Parts > Alarm Socket.
- Press and hold the button on the switch until it lights up.
- Tap ON/OFF icons on the panel to send transmission signals.
- Three flashes from the switch indicate success.
4.7. App Setup (For Cellular + Wi-Fi Models)

Figure 3: The Tuya Smart app interface demonstrating remote control capabilities and integration with smart home products like Google Home and Alexa.
4.7.1. Download App
Scan the QR code in the original manual or search for "Smart Security System" or "Tuya Smart" in your app store.
4.7.2. Signing Up/In
- Register for an account if you don't have one. Check spam/junk folder for verification codes.
- Log in with your email and password.
4.7.3. Adding Device
Important: The hub does not support 5GHz Wi-Fi. If you have a dual-band router with the same SSID for 2.4GHz and 5GHz, separate them into different names. Android users may need to disable cellular data during setup.
- Tap the [+] button on the app's home page.
- Go to
Security & Sensor > Alarm (Wi-Fi). - On the panel, go to
Menu > Wi-Fi > Smart Configuration. "Airlinking..." will be shown. - Enter your Wi-Fi network password in the app.
- The binding process takes about 15 seconds. The device will appear on the app's home page.
5. Operation
5.1. Security Levels
The Smart Hub has three security levels: Away Arm, Home Arm, and Disarm. You can switch between them using the Smart Hub, RFID tag, remote tag, or app.
- Away Arm: All sensors are monitored. Alarm sounds if any sensor is triggered.
- Home Arm: Exterior/perimeter sensors are monitored; interior sensors are not. Useful when you are home but want perimeter security.
- Disarm: No sensors are monitored, except 24-HOUR sensors.
5.2. Arming and Disarming the System
You can arm/disarm using the panel (passcode, ARM/DISARM icons), RFID tag, remote tag, or app.
5.2.1. Using RFID Tag
Tap the RFID tag on the panel's RFID zone to arm or disarm.
5.2.2. Using Remote Tag
- Press Lock to away arm.
- Press Home to home arm.
- Press Unlock to disarm.
- Press SOS for emergency.
5.2.3. Using Panel
- Tap Lock to away arm.
- Tap Home to home arm.
- Tap Unlock to disarm.
5.2.4. Using App
- Tap Lock to away arm.
- Tap Home to home arm.
- Tap Unlock to disarm.

Figure 4: The system provides remote notifications via call, SMS, and app push. It also supports scheduling for automatic arming and disarming at set times.
5.3. Exit/Entry Delay
These delays allow you to exit after arming and enter before disarming without triggering the alarm.
- Exit Delay: Default 40 seconds. Adjustable from 0 to 255 seconds. Go to
Menu > Settings > Delay > Exit Delay. - Entry Delay: Default 30 seconds. Adjustable from 0 to 255 seconds. Go to
Menu > Settings > Delay > Entry Delay.
5.4. Recording a Voice Message
You can record a brief voice message (up to 20 seconds) that plays back when an alarm call is connected.
Go to Menu > Record.
- Select "Record".
- Speak into the panel when "Recording" is shown.
- Press to save.
- Adjust duration via
Menu > Record > Duration. - Play via
Menu > Record > Play. - Delete via
Menu > Record > Delete.
5.5. Scheduling Arm/Disarm
You can set daily schedules for automatic arming and disarming.
Go to Menu > Timer > Arm Timer/Disarm Timer.
- Enter daily arm/disarm time (24-hr format).
- Toggle 'on' to enable the schedule.
- Press to save.
5.6. Making a Call on Panel
On the home screen, tap the phone icon, enter the number, then tap to dial. Calls are cancelled if cellular network is not registered or if the system is armed/in voice alarming.
6. Maintenance
6.1. Battery Replacement
- PIR Motion Detector: Replace three AA 1.5V batteries when the LED indicator blinks for low battery.
- Door/Window Sensor: Replace one CR2032 3V lithium battery when the LED indicator blinks for low battery.
- Remote Tag: Replace one CR2025 Lithium Battery when it stops responding.
6.2. Smart Hub Battery Backup
The hub has a built-in backup battery that lasts over 6 hours during power outages. The battery icon shows its level. A red icon indicates low battery. Full charge takes 8-12 hours.
6.3. General Care
- Keep the hub and sensors dry and clean.
- Avoid extreme temperatures and direct sunlight.
- Do not attempt to repair the system yourself; contact support if issues arise.
7. Troubleshooting
7.1. Common Issues
- No Cellular Network Connection: Ensure SIM card is inserted correctly, activated, and has no security code. Check network coverage.
- Wi-Fi Connection Issues: Verify 2.4GHz network, correct password (no special characters/spaces), and hub proximity to router. Disable AP isolation.
- Sensor Not Triggering: Check sensor battery, ensure it's paired correctly, and within range of the hub. Verify Zone Mode settings.
- App Notifications Not Received: Ensure app has permission to send notifications on your phone. Check app settings for push notifications.
- False Alarms: Check sensor placement (e.g., PIR away from heat sources, door sensors aligned). Adjust PIR sensitivity if available.
7.2. Reset to Factory Settings
Resetting the hub will delete all paired accessories and event logs. You cannot reset if the Smart Hub is locked.
Method 1: Go to Menu > Settings > Initialization and confirm.
Method 2: Press the TAMPER switch underneath the bracket 5 times.
8. Specifications
| Component | Specification |
|---|---|
| Hub |
|
| Remote Tag |
|
| Door/Window Sensor |
|
| PIR Motion Sensor |
|
| RFID Tag |
|
| Wireless Siren |
|
9. User Tips
- Test Sensors Regularly: Periodically test all sensors (door/window, PIR) to ensure they are communicating with the hub and triggering alarms correctly.
- Battery Check: Pay attention to low battery indicators on sensors and replace batteries promptly to avoid system downtime.
- Wi-Fi Stability: For Wi-Fi models, ensure your router is stable and the hub has a strong signal for reliable app control and notifications.
- SIM Card Credit: For GSM models, ensure your SIM card has sufficient credit or an active plan for SMS and call alerts.
- App Permissions: Double-check that the Smart Security System app has all necessary permissions on your smartphone to receive push notifications reliably.
10. Support and Further Information
For more detailed information, advanced configurations, or specific troubleshooting not covered in this manual, please refer to the complete user manual PDF available from the seller or contact customer support.
You can access the full PDF manual here: FUERS G12 User Manual (PDF)