1. Introduction
The GVDA GD153 is a DC resistance type material moisture meter designed to measure the moisture content of various materials, primarily wood and building materials. It displays the moisture content directly as a percentage. This instrument features built-in characteristic parameters for 7 different types of wood and building materials. In addition to moisture content, it also measures ambient humidity and temperature, allowing for a comprehensive evaluation of the environment.
Key Features:
- Measures moisture content in 7 material categories (wood and building materials).
- Single and multi-point average measurement capabilities.
- Data hold function.
- Maximum and minimum value measurement.
- Automatic shutdown (user-cancellable).
- Ambient temperature and humidity measurement.
- Low battery indicator.
- Tricolor backlight (Red, Orange, Green) indicating moisture levels.
2. Safety Information
2.1. Warnings
Before using the product, please read this manual carefully and familiarize yourself with the operation. Keep this manual for future reference.
2.2. Precautions
- Operate the product correctly within the parameters specified in the technical data sheet.
- Do not store this product with solvents, acids, or other corrosive substances.
- Be careful of personal injury caused by the electrode pins. Always cover the protective cap when the product is not in use.
- Do not touch the electrode pins with any charged object to avoid damaging the product.
3. Product Components
The package includes the following items:
- GVDA GD153 Wood Moisture Meter
- Protective Cap
- User Manual (this document and PDF)
- Wrench for probe pin replacement
- 2x Spare Probe Pins
- Storage Bag
4. Setup
4.1. Battery Installation
The GD153 requires 3x 1.5V AAA batteries (not included).
- Ensure the device is powered off.
- Use a screwdriver to loosen the screws on the battery cover located on the back of the device.
- Open the battery cover.
- Insert three new 1.5V AAA batteries, paying close attention to the correct polarity (+/-).
- Close the battery cover and secure it with the screws.
5. Operating Instructions
5.1. Power On/Off
- Press the Power button (
) to turn the device on and enter measurement mode. - Press and hold the Power button to turn the device off.
5.2. Material Category Selection
The GD153 supports 7 different material categories (A-G). To ensure accurate readings, select the appropriate category for the material you are testing.
- Press the M button to cycle through material categories A-G. The selected category letter will be displayed in the lower-left corner of the LCD screen.
- Refer to the 'Material Comparison Table' in the Specifications section or the full PDF manual for detailed material types corresponding to each category.
5.3. Moisture Measurement Procedure
- Turn on the device and select the appropriate material category using the M button.
- Remove the protective cap from the top of the device.
- Carefully insert the two test pins into the material you wish to measure. Ensure good contact. For wood, measure along the grain.
- Read the moisture content, ambient temperature, and humidity displayed on the LCD screen.
- To hold the current measurement on the display, press the H button. The symbol "H" will appear on the LCD. Press H again to release.
- When measurement is complete, remove the pins from the material and immediately replace the protective cap to prevent injury and protect the pins.
5.4. Temperature Unit Selection
- Press the °C/°F button to switch between Celsius and Fahrenheit temperature units.
5.5. Maximum and Minimum Measurement
- Press the MAX/MIN button to activate the maximum and minimum value display function.
- Press MAX/MIN again to cycle through the maximum, minimum, and current values.
- Press and hold the MAX/MIN button for approximately 2 seconds to exit this function.
5.6. Auto Power Off
The device will automatically shut down after approximately 10 minutes of inactivity to conserve battery life.
- To disable the auto power-off function: Press and hold the Power button while turning the device on. The auto power-off symbol will be hidden, indicating the function is cancelled. In this mode, you must manually turn off the device.
5.7. Tricolor Backlight Indication
The LCD backlight color automatically adjusts based on the detected moisture content:
- Green Backlight: Indicates low moisture content (symbol 'O').
- Orange Backlight: Indicates moderate moisture content (symbol 'M').
- Red Backlight: Indicates high moisture content (symbol 'W').
| Backlight Color | Moisture Content Range | Symbol |
|---|---|---|
| Green | 0-15% | O |
| Orange | 15%-24% | M |
| Red | W > 24% | W |
6. Maintenance
6.1. Battery Replacement
Refer to Section 4.1 for detailed instructions on battery replacement.
6.2. Cleaning
Clean the meter surface with a mild detergent and a slightly wet cloth. Do not use abrasive cleaners or immerse the device in water.
6.3. Probe Pin Replacement
If the probe pins become worn or damaged, they can be replaced using the included wrench and spare pins. Carefully unscrew the old pins and screw in the new ones.
7. Troubleshooting
This section addresses common issues you might encounter with your GD153 moisture meter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity. |
| Inaccurate or inconsistent readings. |
|
|
| Display is dim or flickering. | Low battery power. | Replace batteries. |
8. Specifications
| Parameter | Value |
|---|---|
| Sensor Type | Resistance type conductivity measurement, high precision temperature and humidity sensor |
| Display | 2.4-inch Backlight display (Digital) |
| Material A Moisture Range/Accuracy | 9.0% ~ 57.0% RH / ±2.0% |
| Material B Moisture Range/Accuracy | 7.0% ~ 52.0% RH / ±2.0% |
| Material C Moisture Range/Accuracy | 0.9% ~ 21.0% RH / ±2.0% (Cement mortar layer, concrete) |
| Material D Moisture Range/Accuracy | 0.0% ~ 12.0% RH / ±2.0% (Anhydrous gypsum mortar layer) |
| Material E Moisture Range/Accuracy | 0.0% ~ 9.0% RH / ±2.0% (Cement mortar) |
| Material F Moisture Range/Accuracy | 0.5% ~ 10.0% RH / ±2.0% (Lime mortar, gypsum) |
| Material G Moisture Range/Accuracy | 0.0% ~ 17.0% RH / ±2.0% (Brick) |
| Temperature Range | -20.0°C ~ 60.0°C (-4.0°F ~ 140.0°F) |
| Temperature Accuracy | ±1.0°C/2.0°F (0.0°C~45.0°C); ±1.5°C/3.0°F (Other) |
| Humidity Range | 0.0% ~ 99.9% RH |
| Humidity Accuracy | ±5.0% RH (20%-80%); ±6.0% RH (Other) |
| Ambient Temperature | -20.0°C ~ 60.0°C (-4.0°F ~ 140.0°F) |
| Ambient Humidity | 0.0% ~ 99.9% RH / ±4.0% RH |
| Operating Environment | -10°C ~ 50°C / 20% ~ 90% RH |
| Storage Environment | -20°C ~ 60°C / 20% ~ 90% RH |
| Power | 3x 1.5V AAA battery (NOT included) |
| Certifications | CE, FCC |
8.1. Material Comparison Table
For a comprehensive list of wood and building materials corresponding to categories A-G, please refer to the full user manual PDF. A visual representation of the manual page containing this table is provided below.
You can also download the complete user manual in PDF format for detailed material lists and further information: Download User Manual (PDF)
9. User Tips
- When measuring firewood, even if you don't know the exact species, understanding the basic category (e.g., hardwood vs. softwood) can help in selecting the most appropriate setting.
- The inclusion of spare probe pins suggests the manufacturer expects long-term use. Don't hesitate to replace pins if they become dull or damaged to maintain accuracy.
- The clear display and multiple functions make this device versatile for various moisture testing needs.
- Always ensure firm contact between the probe pins and the material for reliable readings.
10. Warranty and Support
For warranty information and customer support, please refer to the seller's policies or contact the GVDA Official Store directly. Keep your purchase receipt as proof of purchase.
For additional technical details and a comprehensive material comparison table, please refer to the full user manual PDF: Download User Manual (PDF)