1. Introduction
The MOES SGW06 2-Outlet Water Timer is designed to automate your outdoor watering needs. Featuring a durable brass inlet, IPX5 waterproof rating, and an intuitive LCD display, this timer offers precise control over irrigation schedules for up to two zones. It includes functions such as timed watering, rain delay, and a child lock for enhanced safety and water conservation.
2. Warnings
- Do not disassemble, reassemble, modify, or attempt to repair this product by yourself. This work should be performed by authorized professionals.
3. Product Overview
The MOES SGW06 Water Timer features a clear LCD display, a rotary dial for mode selection, and intuitive buttons for setting adjustments. It includes two independent outlets for zoned irrigation.


Key Components:
- Filter: Located at the inlet to prevent debris.
- Hose Tap Connection: Brass inlet for connecting to a standard faucet.
- Large Screen: LCD display for time, settings, and status.
- Dial: Rotary knob for selecting operating modes (OFF, SET CLOCK, START TIME, HOW LONG, HOW OFTEN, AUTO).
- + / - Buttons: For adjusting values (hours, minutes, days).
- OK / Manual Button: To confirm settings or initiate manual watering.
- Zone Button: To select between Zone 1 and Zone 2 for programming.
- Zone 1 Outlet / Zone 2 Outlet: Two independent outlets for connecting hoses.
4. Specifications
| Feature | Detail |
|---|---|
| Model | SGW06 |
| Min/Max Operating Pressure | 0.05-0.8Mpa (7.25psi-116psi) |
| Working Temperature | 4.5℃~45℃ (40.1℉~113℉) |
| Power | 2 x AA alkaline batteries (Do not use rechargeable batteries) |
| Waterproof Rating | IPX5 |
| Rain Delay Time | 1 day and up to 7 days |
| High-concerned chemical | None |
| Origin | Mainland China |
| Smart home platform | NONE |

5. Installation
Important Notes:
- This timer is only suitable for 3/4" thread standards.
- Clean the filter regularly and replace it if it's worn to extend the working life of the timer.
- In winter, please remove batteries, drain the timer, and store it indoors to prevent freezing.
- Do not install the timer with tools. Hand tighten ONLY. Using tools may damage the timer.
- Do not subject the product to extreme force and shock.
- To prevent leakage, ensure the water timer is tightly attached to the faucet and hose. Add a rubber washer and thread seal tape if necessary.
- If Zone 1 and Zone 2 are turned on at the same time, the water output time may differ between them.
- For outdoor use only.
5.1 Installing the Battery
- Remove the battery cover on the back of the timer.
- Install 2 new AA (1.5V) alkaline batteries (not included). Ensure they are non-rechargeable.
- Firmly reinstall the cover back into the timer to ensure water resistance.

5.2 Installing the Timer
- Attach the timer to an outdoor hose faucet.
- Please turn on the tap after programming the timer.
6. Operating Instructions
6.1 Set Clock
- Turn the dial to SET CLOCK.
- Press the "+" or "-" button to set the current hour and minutes.
- Use the OK button to switch between setting hours and minutes.
- Turn the dial to save changes.

6.2 Set Start Time
- Turn the dial to START TIME.
- Press the ZONE button to switch between Zone 1 and Zone 2.
- Press the "+" or "-" button to set the desired start hour and minutes.
- Use the OK button to switch between setting hours and minutes.
- Turn the dial to save changes.
Note: If the set START TIME is earlier than the current time (NOW), the scheduled task will be executed the next day.

6.3 Set How Long (Watering Duration)
- Turn the dial to HOW LONG.
- Press the ZONE button to switch between Zone 1 and Zone 2.
- Press the "+" or "-" button to set the watering duration. Duration can be set from 1 minute to 5 hours 59 minutes.
- Use the OK button to switch between setting hours and minutes.
- Turn the dial to save changes.
Note: If the HOW LONG duration is set to 0 minutes, the scheduled task for that zone will not be executed.

6.4 Set How Often (Watering Frequency)
- Turn the dial to HOW OFTEN.
- Press the ZONE button to switch between Zone 1 and Zone 2.
- Press the "+" or "-" button to set the watering frequency. You can choose to water from every 1 to 23 hours, or every 1 to 7 days.
- Turn the dial to save changes.

Examples of watering frequencies:
- Every 1 day: Mon, Tue, Wed, Thu, Fri, Sat, Sun
- Every 2 days: Mon, Wed, Fri, Sun
- Every 3 days: Mon, Thu, Sun
6.5 Auto Mode
- Turn the dial to AUTO. The watering plan you have programmed will be automatically executed.
- The display will show the current day and time, followed by the next scheduled watering plan.
Note: If the HOW LONG duration for a zone is set to 0 minutes, the 'NEXT' display for that zone will show 'OFF'.

6.6 OFF Mode
- Turn the dial to OFF. The screen will show "OFF" and the current battery level.
- All programmed settings are saved, and the timer will stop all watering operations.

6.7 Manual Watering
Ensure the timer is in AUTO mode before initiating manual watering.
- Press the OK button, then use the "+" or "-" buttons to set the desired watering duration (from 0 minutes to 59 minutes).
- Press the ZONE button to switch between Zone 1 and Zone 2 if you want to water a specific zone.
- Press the OK button again to start manual watering for the selected zone(s).
- To end manual watering prematurely, press the OK button once more. The timer will then switch back to AUTO mode.
Note: To manually water only Zone 1, ensure Zone 2's duration is set to 0 minutes. Similarly, for Zone 2 only, set Zone 1's duration to 0 minutes.

6.8 Rain Delay
Ensure the timer is in AUTO mode to set a rain delay.
- Hold the "+" button for 5 seconds until the rain cloud icon appears on the screen.
- Press the "+" or "-" button to set the duration of the delay, from 0 to 7 days.
- Press the OK button to save the changes.
- To quit the Rain Delay function, hold the "+" button for 5 seconds again.

6.9 Child Lock Function
Ensure the timer is in AUTO mode to activate the child lock.
- Hold the "-" button for 5 seconds until the lock icon appears on the screen. This prevents accidental changes to settings.
- To cancel the child lock, hold the "-" button for 5 seconds again.

7. Battery Status
The battery status will be displayed on the LCD screen as either FULL or LOW BATTERY.

Note: When the low battery indicator appears, the valve will close automatically to avoid leakage. Please replace the batteries in time to prevent interruption of normal operation.
8. Troubleshooting
| Problem | Possible Cause | Possible Solution |
|---|---|---|
| Leakage |
|
|
| Water won't stop/flow out |
|
|
| Short battery life |
| Use new alkaline batteries. |
| Low water pressure |
|
|
| No response for manual/rain delay function | After setting manual watering or rain delay time, the OK button was not pressed to save and run. | Press the OK button again after the time is confirmed. |
9. User Tips
- Always use fresh, non-rechargeable AA alkaline batteries for optimal performance and battery life.
- Regularly check and clean the filter to prevent blockages and maintain consistent water pressure.
- In cold weather, remove the timer and batteries to prevent freezing damage and extend product lifespan.
- Utilize the child lock function to prevent accidental changes to your watering schedule, especially in households with children.
- Remember to press the "OK" button after setting any manual or rain delay functions to ensure they are saved and activated.
10. Maintenance
- Filter Cleaning: Regularly inspect and clean the inlet filter to prevent debris buildup, which can affect water flow and pressure.
- Winter Storage: Before the first frost, remove the timer from the faucet, drain any remaining water, remove the batteries, and store the unit indoors in a dry, protected area.
- Battery Replacement: Replace batteries promptly when the low battery indicator appears to ensure continuous operation and prevent automatic valve closure.
11. FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
12. Recycling Information
All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

13. Warranty and Support
Warranty Instructions:
Thank you for purchasing this product. The warranty for this product is granted as follows:
- Warranty Period: Products are covered by a 24-month warranty, effective from the date of purchase by a retail customer.
- Proof of Purchase: To exercise warranty rights, the purchaser must present a Warranty Card and Proof of Purchase (VAT invoice, financial receipt, or other document confirming the actual date of purchase).
- Defect Reporting: If product quality problems occur within 24 months from the date of receipt, prepare the product and packaging and contact your place of purchase for after-sales maintenance. If the product is damaged due to personal reasons, a maintenance fee will be charged.
- Shipping for Service: We recommend using the original packaging with padding to ensure safe transportation when delivering the product for service. If using replacement packaging, ensure adequate protection from damage. Consider placing a "Warning Glass" sticker if susceptible to impact.
- Resolution Time: Reported defects covered by the warranty will be considered immediately and no later than 14 days from the date of delivery to the Guarantor. After checking and determining the legality of the warranty claim, the Guarantor will repair the product within a reasonable time, not exceeding 30 days from the date of delivery. This deadline may extend if hard-to-find spare parts are required.
- Warranty Exclusions: The warranty does not cover performance of maintenance and similar operations specified in the user manual (users are obliged to do these themselves), defects due to natural wear and tear, mechanical damage caused by user fault, damage caused by improper use, or use of non-original parts and consumables.
- Warranty Void: The warranty will expire if the warranty seal or serial number is removed from the product, or if actions are taken to eliminate physical defects outside of authorized service.
Support Contact:
Manufacturer:
WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel: +86-577-57186815
After-sale Service: service@moeshouse.com
UK Representative (UK REP):
EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292–1680945
Email: contact@evatmaster.com
EC Representative (EC REP):
AMZLAB GmbH
Laubenhof 23, ESSEN 45326
Email: info@amz-lab.de
Tel: +491745298066
Made In China