BEISHI CX01-01 Single Screen Monitor Stand User Manual

1. Introduction

Thank you for choosing the BEISHI CX01-01 Single Screen Monitor Stand. This gas spring full-motion desk mount is designed to enhance your viewing experience and free up valuable desk space. It supports monitors from 13 to 32 inches and offers a wide range of adjustments for optimal ergonomic positioning. Please read this manual carefully before installation and retain it for future reference.

Safety Precautions

Please read this manual carefully before installation.

• If you do not understand the instructions or have any questions, contact a qualified local installer.
• Do not exceed the specified weight capacity (2-9kg / 4.4-19.8 lbs). Overloading may cause the bracket to shake and result in injury.
• Strictly follow all installation instructions. Improper installation can lead to product damage or personal injury.
• Use appropriate installation tools and ensure professional installation if unsure.
• Verify that the supporting surface (desk) can safely support the combined weight of the equipment and all accessories.
• Use only the provided screws for installation. Do not overtighten screws.
• This product contains small parts that could be a choking hazard. Keep out of reach of infants.
• This product is for indoor use only. Outdoor use may cause product failure and personal injury.
• For safety, inspect the product at least every three months for any signs of wear or damage.
• Before installation, confirm all parts are complete and undamaged. Contact your dealer for replacements if needed.

2. Package Contents

Please check the package to ensure all components are present and undamaged:

Mounting Accessories

• Telescopic arm (x1)
• Base (x1)
• Connector (x1)
• Fixing clip (x1)
• Cable clamp (x1)
• Support rod (x1)
• Panel (x1)

Installation Screw Accessories

• M-A: M4x12mm screws (x4)
• M-B: M4x30mm screws (x4)
• M-C: D4 gaskets (x4)
• M-D: 13mm height-enhancing pads (x4)
• A: M6x10mm screws (x4)
• B: M6x20mm screws (x3)
• C: (Unspecified part, x1)
• D: 4mm wrench (x1)
• E: 5mm wrench (x1)
• F: 6mm wrench (x1)

3. Specifications

Figure 1: Monitor Stand Overview with Key Specifications

Figure 2: Clamp and Grommet Mounting Options

Figure 3: Full Motion Flexibility and Adjustment Ranges

4. Setup and Installation

4.1. Installation of the Base

1. Install Support Rod and Base: Connect the support rod (6) to the base (2). Use screw B to fix them together. Tighten securely with wrench E.
2. Install Connectors: Attach connector (3) to the base. Use screw A to secure it, then tighten with wrench D.

4.2. Installation of the Fixing Clip and the Tabletop (Punch-Free Method)

Choose the appropriate hole position on the fixing clip based on your desk thickness:

• For 50-85mm Desktop Thickness: Install the fixing clip in the second and third holes.
• For 10-55mm Desktop Thickness: Install the fixing clip in the first and second holes.

Once the fixing clip is assembled, place the base onto your desktop and tighten the clamp securely until the stand is stable.

4.3. Installation of the Fixing Clip and the Tabletop (Nail Drill Method)

1. Disassemble Fixing Clip: Use wrench F to disassemble the retaining clip assembly from the base.
2. Drill Hole: Use an electric drill to create a hole in your desktop at the desired installation location. The hole diameter should be between 10-20mm.
3. Secure Base: Insert the long screw (from the disassembled fixing clip) through the iron piece and the drilled hole. Secure the base cover from underneath the desk.

4.4. Installation of Telescopic Arm

1. Mount Cable Clamp and Arm: Slide the cable clamp (5) onto the support column, followed by the telescopic arm (1).
2. Tighten: Once the telescopic arm is in position, use wrench F to tighten the screw on the arm's collar to secure it to the support column.

4.5. Panel and Display Installation

This step involves attaching the VESA panel to your monitor.

• For Monitors with a Flat Back:
  1. Align the panel (7) with the VESA mounting holes on the back of your monitor.
  2. Use M-A (M4x12mm) screws and M-C (D4 gaskets) to secure the panel to the monitor. No height-enhancing pads are needed.
  3. Tighten with wrench F.
• For Monitors with a Non-Flat Back (Recessed VESA or Curved):
  1. Align the panel (7) with the VESA mounting holes on the back of your monitor.
  2. Use M-B (M4x30mm) screws, M-C (D4 gaskets), and M-D (13mm height-enhancing pads) as needed to ensure the panel sits flush and securely.
  3. Tighten with wrench F.

4.6. Mount the Monitor on the Telescopic Arm

1. Prepare Arm: Before mounting the monitor, ensure the knob on the telescopic arm's VESA head is unscrewed to allow the panel to slide in.
2. Attach Monitor: Carefully slide the monitor (with the attached panel) onto the VESA head of the telescopic arm.
3. Secure Monitor: Align the panel holes with the telescopic arm holes. Tighten the knob to secure the monitor in place.

4.7. Installation of Cable Harness

1. Remove Cover: Gently pull to remove the harness cover from the telescopic arm.
2. Route Cables: Route your monitor cables (power, video, etc.) through the channel in the telescopic arm.
3. Replace Cover: Align the harness cover with the holes and insert it along the direction of the telescopic arm until it clicks into place.

5. Operating Instructions

5.1. Angle Adjustment

• Panel Angle (Tilt): When adjusting the tilt angle of the monitor panel, use the screws on the retractor arm to adjust the angle.
• Swivel and Rotation: The arm allows for ±90° swivel and 360° rotation. Gently move the monitor to your desired position.

Important: Do not use the bracket in the opposite direction of its intended range of motion to avoid damage.

5.2. Post-Installation Display Adjustment (Spring Tension)

The gas spring tension needs to be adjusted to match your monitor's weight for smooth vertical movement.

• Monitor/Telescopic Arm Downward Adjustment (Increase Spring Tension): If your monitor sags or moves down too easily, use the Allen wrench (E) to adjust the screws on the telescopic arm. Turn counterclockwise ("+" direction) to increase the air spring tension.
• Monitor/Telescopic Arm Upward Adjustment (Reduce Spring Tension): If your monitor floats up or is difficult to push down, use the Allen wrench to adjust the screws on the telescopic arm. Turn clockwise ("-" direction) to reduce the air spring tension.

5.3. Bracket Angle Adjustment Range

• Tilt: ±90° (up/down)
• Swivel: ±180° (left/right at arm joint)
• Rotation: ±360° (full rotation of monitor screen)
• Vertical Arm Movement: ±135° (up/down movement of the main arm)

6. Maintenance

• Cleaning: Clean the monitor stand with a soft, damp cloth. Avoid using abrasive cleaners or solvents, as they may damage the finish.
• Periodic Checks: Every three months, check all screws and connections to ensure they are tight and secure. Re-tighten if necessary.
• Gas Spring: The gas spring is maintenance-free. Do not attempt to open or service it.

7. Troubleshooting

• Monitor Sags or Floats: Adjust the gas spring tension as described in Section 5.2.
• Stand is Wobbly: Ensure the desk clamp/grommet mount is securely tightened to the desk. Check all arm joints and VESA plate screws for tightness.
• Difficulty Adjusting Monitor: Ensure the gas spring tension is correctly set for your monitor's weight. If joints are too stiff, check for overtightened screws and loosen slightly if necessary (without compromising safety).

8. User Tips

• Cable Management: Utilize the integrated cable management system to keep your workspace tidy and prevent cable damage.
• Ergonomics: Position your monitor so the top of the screen is at or slightly below eye level, and your eyes are about an arm's length away from the screen. This helps reduce neck and eye strain.
• Desk Space: Take advantage of the freed-up desk space by organizing your peripherals or adding desk accessories.

9. Warranty and Support

For warranty information or technical support, please refer to your purchase documentation or contact the retailer where you purchased this product. Keep your proof of purchase for any warranty claims.