Introduction
This manual provides detailed instructions for the safe and effective operation of your Radtel RT-860 All Band Ham Radio. Please read this manual thoroughly before using the device and keep it for future reference.
The Radtel RT-860 is a versatile handheld two-way radio featuring all-band reception (AM, SSB, CB, HF, VHF, UHF) and transmission capabilities on VHF/UHF bands. It offers 1024 channels, a 2000mAh battery, and a Type-C charging port. Key features include AI anti-noise, frequency copy function, and robust construction.
Safety Precautions
To prevent fire, personal injury, equipment damage, or other accidents, observe the following precautions:
- Do not use the equipment in inflammable or explosive environments (e.g., gas, dust, smoke). Turn off the equipment when refueling or parking at a gas station.
- Do not place the equipment in dusty, wet, or splashed locations, or on uneven surfaces.
- Use this equipment away from interference sources such as TVs, computers, or distribution cabinets.
- Do not transmit while charging.
- Do not use the radio while driving.
- Do not expose the device to direct sunlight for extended periods or place it near heating devices.
- If the equipment emits an abnormal odor, turn it off immediately. After ensuring safety, send it to the nearest maintenance site for inspection.
- Do not modify or adjust this equipment for any reason.
- Always obey local laws and regulations.
Disclaimer: The customer is responsible for any equipment failure or accident caused by violating these precautions. The company is not responsible for such incidents.
Familiarization with Your Radio
The Radtel RT-860 features a robust design with intuitive controls. Understanding the layout of your radio is essential for effective operation.
Radio Components Overview
The radio's front panel includes a display screen, keypad, speaker, and microphone. The top features the antenna, ON/OFF/Volume knob, and an indicator light. The side includes the PTT (Push-To-Talk) button, Side-key 1, and Side-key 2. The bottom houses the Type-C charging port and the earpiece/programmable jack.
- Antenna: For transmitting and receiving signals.
- ON/OFF/Volume Knob: Powers the radio on/off and adjusts volume.
- Indicator: LED light for status indications.
- Alarm Button: Activates emergency alarm functions.
- Speaker: Audio output.
- MIC: Microphone for voice input.
- Display Screen: Shows frequency, channel, battery status, and other operational information.
- Keypad: For inputting frequencies, channel numbers, and menu navigation.
- PTT (Push-To-Talk): Press and hold to transmit.
- Side-key 1 & 2: Programmable function keys.
- Earpiece/Programmable Jack: Connects earpieces or programming cables.
- Type-C Charging Port: For charging the radio's 2000mAh battery.
Setup and Basic Operation
Battery Installation and Charging
The RT-860 comes with a 2000mAh battery. Ensure the battery is properly installed before use. To charge, connect the provided Type-C cable to the radio's charging port and a suitable power source.
Antenna Attachment
Screw the antenna clockwise onto the connector at the top of the radio until it is finger-tight. Do not overtighten.
Power On/Off and Volume Adjustment
Rotate the ON/OFF/Volume knob clockwise to power on the radio. Continue rotating to increase the volume. Rotate counter-clockwise to decrease volume and power off.
Keypad Functions
The keypad provides access to various functions and input methods:
| Key | Function |
|---|---|
| PTT | Transmit or Exit |
| Alarm Key | Definable long press and short press functions. Can be secondary PTT via Menu. |
| Side key 1 & 2 | Definable long press and short press functions. |
| ▲ / ▼ | Switch upwards / Switch downwards. |
| 0-9 | Input numbers, English letters, Chinese characters. Long press for definable functions. |
| * | Long press to lock keypad. Short press to delete. |
| # | Switch working mode (VFO/channel/zone). Activate inputting status and switch input methods. |
LCD Display Indicators
The LCD provides critical information about the radio's status and operation. Key indicators include:
- VFO MODE / CH MODE / ZONE-XXX Mode: Indicates current operating mode.
- Main frequency icon: Shows the primary frequency.
- Channel number: Displays the active channel.
- AM or FM Analog RX modulation: Indicates the current modulation type for reception.
- CTC/DCS analog channel: Shows sub-tones/digital sub-tones/encrypted sub-tone/decoded sub-tone status.
- H/L: High/Low Power setting.
- W/N: Wide/Narrow Bandwidth setting.
- Sub-display information: Secondary information display.
- Main Display information: Primary information display.
- RSSI Value: Received Signal Strength Indicator.
- Battery Power: Battery level indicator.
- Beep: Indicates keypad tone status.
- Dual standby: Shows if dual standby is active.
- Scanning: Indicates scanning is active.
- R-Talk around / T-Freq Inverse: Repeater functions.
- Keypad Lock: Indicates if the keypad is locked.
- Signal Icon: Shows signal presence.
Operating Instructions
Inputting Frequencies
- Switch to VFO frequency mode by pressing the # key.
- Input the desired frequency using the number keys (6 or 8 digits).
- To set the inputting digits (6 or 8 bits), navigate to Menu > [Radio Set] > [6 or 8 Bits Input].
Inputting Repeater Frequency
Method 1:
- Enter Menu > [Channel Set] > [Offset Freq] to input the frequency difference using the keypad.
- Enter Menu > [Channel Set] > [Offset DIR] to set the frequency upwards or downwards.
Method 2:
- Long press the # button to enter [TX Frequency] and input the TX frequency. Press O to confirm, then return to the previous menu.
- Press ▲ / ▼ to set CTCSS/DCS.
Transmitting and Receiving
Transmitting:
- Press and hold the PTT button to transmit at the current frequency. The indicator light will turn red.
- To set PTT behavior (e.g., transmit in Area A or Main Area), go to Menu > [Basic Set] > [Main PTT TX].
- Side-key 1 can be configured as a secondary PTT for transmitting on a different frequency (Menu > [Key Define] > [Slaver PTT]).
Receiving:
- The indicator light will turn green when receiving a signal.
- If there is no RX sub-tone or the sub-tone matches, the speaker will output audio.
DTMF Functions
DTMF Inputting and Sending:
- Press O to enter the DTMF inputting interface while in standby.
- Use numeric keys to input DTMF codes. Press * to delete the last code.
- Press PTT to send the DTMF code to the receiver after the appointed delay time.
DTMF Remote Monitor:
- Enable DTMF Control in (Analog Set).
- When other radios send DTMF code with the same monitor code, this radio will receive it.
- After successful decoding, the radio will automatically transmit for 60 seconds to enable remote monitoring.
DTMF Stun/Kill/Activate:
- Set up a DTMF code for Stun/Kill/Activate and enable [DTMF Control].
- Other radios can Stun/Kill/Activate this radio by sending the relative DTMF code.
- A radio in "Kill" status cannot be used until an "Activate" code is received. In "Stun" status, it can receive but cannot input or transmit.
- Note: An Activate code must be set up when a Stun/Kill code is set up, otherwise the device cannot be activated.
Text Input
- Press # to switch inputting methods. Press * to delete inputting characters.
- Use number keys (123) to input numbers.
- For English letters, keys 2-9 input letters, 0 for space, and 1 for symbols. Press the same button to cycle through different letters.
Definable Keys
Side keys can be programmed for various functions:
- [Monitor]: Enters receiving and playing status.
- [H/L Power]: Switches high/low power for the current channel.
- [Dual Standby]: Toggles dual standby. (Power saving mode is invalid when dual standby is on).
- [TX Priority]: Switches priority RX to [Edit] or [Busy]. In Busy status, the main frequency shifts to the calling frequency when a call ends.
- [Scanning]: Enters scanning mode. Press any key to exit.
- [Backlight On-off]: Toggles backlight.
- [Roger Beep]: Switches RX end tone types.
- [FM Radio]: Enters FM status. Press PTT to exit.
Menu Settings
The radio's functionality can be customized through its menu system. Here are some key menu options:
Basic Set Menu
| Menu Item | Sub Menu | Function |
|---|---|---|
| 01 Name/Callsign | Edit name | Set radio name or callsign. |
| 02 Voice Prompt | On/off | Turn on/off voice prompt. |
| 03 Key Beep | On/off | Turn on/off keypad beep. |
| 04 Lock Timer | Off, 5s-600s | Time to lock keypad automatically. |
| 05 Brightness | 0-6 level | Adjust background light brightness. |
| 06 Backlight | On/off | Turn on/off display backlight. |
| 07 Light Timer | Off, 5s-600s | Time to turn off backlight. |
| 08 Menu Exit | Off, 5s-600s | Time to exit menu automatically. |
| 09 State Timer | Off, 5s-600s | Show voltage, time, date. |
| 10 Dual Standby | On/off | Select dual standby or single standby. |
| 11 TX priority | Edit / Busy | Always transmit at main band / Switch to busy channel as main band. |
| 12 Freq Step | Various options | Set the frequency or scan step. |
| 13 Talk Around | Off, Talk Around, Invert Freq | Set repeater mode or normal mode. |
| 14 Save Mode | Off, 1:1-1:3 | Set the power saving ratio. |
| 15 Scan Mode | CO / TO / SE | Configures scanning behavior (stops on signal, continues after signal, or exits scan). |
| 16 Scan Direction | UP, DOWN | Set the scanning direction. |
| 17 Scan Dwell | 0-30 | Set the scan stop time for TO scan mode. |
| 18 Scan Return | Original CH, Current CH | Set the channel after scanning. |
| 19 Alarm Type | Local Alarm, Remote Alarm, Local+Remote | Configures alarm sound behavior. |
| 20 Main PTT TX | Area A, Main Area | Transmit in main area or always in A area. |
| 21 Dual Display | Dual, Single | Dual display or Single display. |
| 22 Area A Mode | CH mode, Zone mode, Freq mode | Set the display mode for Area A. |
| 23 Area A Show | Show CH No, Show Freq, Show Alias | Set the display way in the selected mode. |
| 24 Area A Zone | Zone1-Zone256 | Set the zone numbers. |
| 25 Area B Mode | CH mode, Zone mode, Freq mode | Set the display mode for Area B. |
| 26 Area B Show | Show Freq, Show Alias, Show CH No. | Set the display way in the selected mode. |
| 27 Area B Zone | Zone-001-Zone-256 | Set the zone numbers. |
| 28 Save CH | CH-0001-CH-1024 | Save frequency and tone into channels. |
| 29 Delete CH | CH-0001-CH-1024 | Delete frequency and tone from a channel. |
| 30 Instruction | barcode | Scan barcode to get user manual (refer to PDF). |
| 31 LCD Contrast | 0-30 | Adjust display contrast (requires restart). |
| 32 Freq Input | 6 bits, 8 bits | Input frequency in 6 bits or 8 bits. |
| 33 Initialization | Cancel, Ensure | Confirm or cancel initialization. |
| 34 Version | Show version information. |
Analog Set Menu
| Menu Item | Sub Menu | Function |
|---|---|---|
| 01 SQ level | 0-10 | Sets squelch level. Lower levels are more susceptible to interference. |
| 02 TX Start Tone | On, off | Sets the tone before transmitting. |
| 03 TX End Tone | OFF, Roger Beep 1/2, Send Radio Name | Sets the tone at the end of transmission or sends radio name. |
| 04 Single Tone | 1750Hz | Edits the tone frequency in Key Define. |
| 05 Mic Gain | 0-31 | Adjusts microphone sensitivity. |
| 06 SPK Gain | 0-63 | Adjusts speaker volume. |
| 07 Glitch TH | 0-10 | Sets Glitch threshold value. |
| 08 Detect Range | Frequency range | Sets frequency range to detect from other radios. |
| 09 Repeater Delay | 0-2000ms | Sets repeater delay time. |
| 10 DTMF Delay | 0-2000ms | Sets DTMF delay time. |
| 11 DTMF Interval | 30-200ms | Sets DTMF interval time. |
| 12 DTMF Duration | 30-200ms | Sets DTMF Duration Time. |
| 13 DTMF Mode | Off, Tx Start & End | Sets transmit DTMF code mode. |
| 14 DTMF Select | DTMF-01-DTMF-16 | Selects DTMF code 1-16. |
| 15 DTMF Display | On, off | Turns on/off display DTMF decode. |
| 16 DTMF TX Gain | 0-127 | Sets DTMF Transmit Gain. |
| 17 DTMF RX TH | 0-63 | Sets DTMF Receive threshold. |
| 18 DTMF Control | 0-2000ms | Turns on/off DTMF control. |
| 19 Time Calibrate | On, off | Remote Time Calibrate. |
| 20 RSSI Refresh | 0-5 | Sets refresh interval for RX field. |
| 21 VOX | 0-245 | Sets VOX sensitivity. |
| 22 VOX Delay | On, off | Sets VOX delay. |
| 23 VOX TH | On, off | Sets VOX threshold. |
Channel Set Menu
| Menu Item | Sub Menu | Function |
|---|---|---|
| 01 CTC/DCS | Off, #Switch Type | Set up RX and TX sub-tone of current channel. |
| 02 RX CTC/DCS | Off, #Switch Type | Set up RX sub-tone of current channel. |
| 03 TX CTC/DCS | Off, #Switch Type | Set up TX sub-tone of current channel. |
| 04 Set TX Freq | 454.525MHz | Set TX frequency of current channel. |
| 05 DCS Encrypt | Standard, Encrypt 1/2/3, Mute code | Configures DCS encryption or mute code. |
| 06 Mute Code | 00000000 | Non-standard sub-tone obtained using "freq detect" function. |
| 07 Band Width | Wide/Narrow | Sets the bandwidth occupied by the channel. |
| 08 Tail Tone | Off, on | Eliminates receiver's tail sound at the end of TX. |
| 09 Scrambler | Off, 1-8 | Adds interference frequency to speech. |
| 10 Busy Lock | Off, Carrier Match, CTC/DCS Match | Allows/prohibits transmission when receiving a signal. |
| 11 TX Power | Low, High | Sets transmission power. |
| 12 Scan Add | Add, Remove | Adds/removes current channel to scanning queue. |
| 13 TOT | Off, 5S-60S | Sets time allowed for continuous transmission. |
| 14 CH Alias | Sets the alias of the current channel. | |
| 15 Offset Dir | Sets frequency offset direction. | |
| 16 Offset Freq | 000.00000MHZ | Sets frequency direction of the current channel. |
| 17 AM/FM RX | FM, AM | Sets the demodulation standard for the current channel. |
Zone Set
The radio supports 256 zones. You can edit each zone name and its channels. There are 1024 channels available in total across all zones.
Radio Menu
| Menu Item | Sub Menu | Function |
|---|---|---|
| 01 RX Standby | Off, on | Exit the radio or not when there is a call signal. |
| 02 Channel List | Edit Name, CH001-CH128, Set As Current | Edit channel name, select channel, or set as current. |
Time Message Menu
| Menu Item | Sub Menu | Function |
|---|---|---|
| 01 APO | Off, on | Set auto power on/off. |
| 02 APO Timer | Power off timer | Set power off timer. |
| 03 AWU | Off, on | Timed exit from APO sleep state. |
| 04 AWU Timer | 0000:30:00 | Sets time to automatically exit APO sleep state. |
FM Radio Operation
- [RX Standby]: Set to [On] to allow the radio to standby for calling signals on the main channel while in FM radio status.
- [Channel List]: Access 128 preset FM radio channels. Select a channel and press O to confirm. You can edit channel names or set a channel as current.
- Time Management (APO/AWU):
- [APO] (Auto Power Off): Toggles auto shutdown.
- [APO Timer]: If no actions are performed, the radio will shut down automatically after this timer expires.
- [AWU] (Auto Wake Up): Toggles activation function.
- [AWU Timer]: When the AWU timer is reached, the radio exits dormancy and returns to working status.
Maintenance
- Cleaning: Use a soft, damp cloth to clean the radio's exterior. Do not use harsh chemicals or solvents.
- Battery Care: To prolong battery life, avoid overcharging or completely discharging the battery. Charge the battery in a well-ventilated area.
- Storage: When not in use for extended periods, store the radio in a cool, dry place. Remove the battery if storing for more than a month.
- Antenna: Regularly check the antenna for damage. Replace if bent or broken to ensure optimal performance.
- Firmware Updates: Check the manufacturer's website for any available firmware updates to improve performance or add features.
Troubleshooting
If you encounter issues with your RT-860, try the following steps:
- Radio not powering on:
- Check if the battery is charged and properly installed.
- Ensure the ON/OFF/Volume knob is rotated sufficiently clockwise.
- No reception/transmission:
- Verify the antenna is securely attached.
- Check the frequency and channel settings.
- Ensure TX power is set appropriately (Low/High).
- Check if "Busy Lock" is enabled, preventing transmission when a signal is present.
- If in "Stun" status, the radio cannot transmit. An "Activate" code is required.
- Poor audio quality/interference:
- Adjust the SQ (Squelch) level. A lower level might pick up more noise.
- Check