Introduction
Thank you for purchasing the MILESEEY D5T Laser Distance Meter. This manual provides detailed instructions for safe and effective use of your device. Please read it carefully before operation to ensure optimal performance and to prevent any potential damage or injury.
The MILESEEY D5T Laser Measure offers 8 distinct functions, designed to meet various measuring needs and enhance your user experience.
Safety Information
CAUTION
For the safe use of this handheld laser distance meter, please read the following instructions carefully:
- The device is categorized as a Class 2 laser product. DO NOT stare directly into the laser beam or point it at others, as this can cause eye damage.
- The product is manufactured in accordance with strict standards and regulations. However, it cannot entirely exclude the possibility of interference with other devices, or causing discomfort to humans and animals.
- DO NOT use this product in explosive or corrosive environments.
- DO NOT use this product near medical devices.
- DO NOT use this product on an airplane.
Disposal
Everyone is responsible for environmental protection. It is prohibited to dispose of used batteries with household waste. Please collect used batteries and dispose of them at designated waste stations.
This product must not be recycled with household waste. Dispose of the product appropriately in accordance with the national regulations in your country.
Scope of Responsibility
Mileseey will not be responsible for damages caused by improper use, including but not limited to:
- Using the product without following instructions.
- Using accessories from other manufacturers without Mileseey's approval.
- Modifying or converting the product.
Setup
Battery Insertion
Open the battery compartment and insert two AAA alkaline batteries according to the polarity indicators inside the compartment. For safety, ensure the compartment lid is securely closed after battery insertion.

LCD Display
The 2-inch large LCD display provides clear readings and icons, even in varying light conditions. It features a backlight for dark areas.

Key indicators on the display include:
- Laser on indicator
- Front reference point indicator
- Rear reference point indicator
- Distance/Continuous measurement mode
- Measuring mode indications (5, 6, 7, 8)
- Battery status
- Historical memory indicator
- Value 1 (current measurement)
- Value 2 / Minimum value
- Value 3 / Maximum value
- Summary line / Latest value / Calculation result
Initial Operation and Settings
Power On / Off
- Manual Power On/Off: Long press the ON/OFF/Return/Clear button to switch the device on or off.
- Automatic Power Off: The instrument will automatically switch off after three minutes of inactivity to conserve battery.
Return / Clear
When measuring, press the ON/OFF/Return/Clear button to undo the last action or clear the displayed measured value.
Adjusting Measuring Reference
Press the Measuring Reference / Unit button to switch the reference point between the front and the rear of the instrument. The default reference setting is from the rear of the device. The reference point can be set and saved manually.
Unit Change
Long press the Measuring Reference / Unit button to change the distance unit between meters (m), feet (ft), inches (in), and feet+inches (ft+in).

Beep On/Off
Press the Beep button to toggle the audible beep sound on or off. This is useful for quiet environments like libraries or classrooms.
Measurement Modes
The Mileseey D5T offers multiple measurement functions to suit various applications.

Single Distance Measurement
- Press the MEASURE button once to activate the laser.
- Press the MEASURE button again to trigger the distance measurement. The measured value will be displayed immediately.
Continuous Measurement (Min / Max)
Long press the MEASURE button to activate continuous measurement. The device will continuously measure and display the minimum and maximum values detected. This function automatically stops after 5 minutes of inactivity. You can also press the MEASURE or CLEAR button to stop it manually.
Area Measurement
- Press the Area/Volume/Pythagorean button once. The area symbol (a square) will appear on the display.
- Press the MEASURE button to take the first distance measurement (e.g., length).
- Press the MEASURE button again to take the second distance measurement (e.g., width).
- The results for length, width, perimeter, and area will be displayed on the screen.
Volume Measurement
- Press the Area/Volume/Pythagorean button twice. The volume symbol (a cube) will appear on the display.
- Press the MEASURE button to take the first distance measurement (e.g., length).
- Press the MEASURE button again to take the second distance measurement (e.g., width).
- Press the MEASURE button a third time to take the third distance measurement (e.g., height).
- The results for length, width, height, and volume will be displayed in order.
Pythagorean Measurement
Pythagoras measurement can be applied to different flat surfaces. Ensure the vertical edge is perpendicular to the measured object for accuracy.
Notes for Pythagorean Measurement:
- All measured points should be on the same horizontal or vertical plane.
- For more accurate results, the laser rangefinder should be measured at a fixed rotation point.
- According to the Pythagorean Theorem, the right-angle side cannot be larger than the hypotenuse; otherwise, a calculation error will occur.
Pythagorean Method - Two Points (Type 1)
- Press the Area/Volume/Pythagorean button three times. The Pythagorean Type 1 symbol will appear on the display.
- Take measurements at two points as indicated in the display's diagram. The height of the object will be automatically calculated and displayed.
Pythagorean Method - Three Points (Type 2)
- Press the Area/Volume/Pythagorean button four times. The Pythagorean Type 2 symbol will appear on the display.
- Take measurements at three points as indicated in the display's diagram. The height will be calculated and displayed on the summary line.
Pythagorean Method - Three Points (Type 3)
- Press the Area/Volume/Pythagorean button five times. The Pythagorean Type 3 symbol will appear on the display.
- Take measurements at three points as indicated in the display's diagram. The height will be calculated and displayed on the summary line.
To delete any measured length, press the CLEAR button, then press MEASURE to re-measure.
Addition / Subtraction
The device supports adding and subtracting measurements:
- Addition: Short press the Add(+) / Subtract(-) button.
- Subtraction: Long press the Add(+) / Subtract(-) button.
After taking a measurement, press the Add(+) / Subtract(-) button. The corresponding symbol will appear on the display. Then, press the MEASURE button to take the second measurement. The second value will be automatically added to or subtracted from the first one. This process can be repeated as required for multiple calculations.
Historical Memory
Continuous long press the Historical Memory button to view historical measurements. The last 30 measured values will be displayed in reversed order. Press the CLEAR button to exit historical value viewing.
User Tips
- For outdoor measurements or in bright conditions, using a target plate can significantly improve accuracy and range.
- When using Pythagorean modes, ensure the device is held steady and the laser hits the target points precisely to avoid errors.
- The Bluetooth connectivity allows for real-time data transfer to a smartphone app like "SmartLife" or "JoyPlan", which can be very useful for documenting measurements and creating floor plans. Experiment with these apps to enhance your workflow.
- Utilize the mute function when working in noise-sensitive environments to avoid disturbance.
Troubleshooting
All errors or failures will be indicated by specific codes on the display. The table below explains common codes and their solutions:
| Code | Cause | Corrective Measure |
|---|---|---|
| 204 | Calculation error | Refer to user manual, repeat the procedures. |
| 208 | Excessive current | Please contact your distributor. |
| 220 | Battery low | Replace with new batteries. |
| 252 | Temperature too high | Working temperature of this device is 0°C ~ +40°C (32°F ~ +104°F). |
| 253 | Temperature too low | Working temperature of this device is 0°C ~ +40°C (32°F ~ +104°F). |
| 255 | Received signal too weak or measurement time too long | Use a target plate or change to a good reflective surface. |
| 256 | Received signal too strong | Target too reflective; use a target plate or do not aim at strong light sources. |
| 261 | Outside of the range of measurement | Select the measurement distance within the specified range of measurement. |
| 500 | Hardware error | Switch the device on/off several times. If the symbol still appears, please contact your dealer for assistance. |
Specifications
| Feature | Specification |
|---|---|
| Maximum Measuring Range | 0.2-50m / 100m (depending on model) |
| Measuring Accuracy | ±(2.0mm + 5x10-5D) |
| Measuring Units | m / ft / in / ft+in |
| Laser Class | Class 2 |
| Laser Type | 630-670nm, < 1mW |
| Area, Volume Measurement | Yes |
| Indirect Pythagorean Theorem | Yes |
| Addition and Subtraction | Yes |
| Continuous Measurement | Yes |
| Min. / Max. Value | Yes |
| Beep | Yes |
| 4-line Display with Backlight | Yes |
| Single Distance Measurement | Yes |
| Historical Memory | 30 sets |
| Button Type | Soft rubber buttons |
| Operating Temperature | 0°C ~ 40°C |
| Storage Temperature | -10°C ~ 60°C |
| Battery Life | Up to 5,000 measurements |
| Battery Type | 2 x AAA 1.5V |
| Auto Laser Off | 30 seconds |
| Auto Instrument Off | 180 seconds |
| Dimensions (mm) | 115 x 50 x 28 |
Note: The maximum measuring range is determined by the version of the laser distance meter. In daylight or if the target has poor reflection properties, please use a target plate. In favorable conditions (good target surface properties, room temperature), the device can reach up to its rated measuring range. In unfavorable conditions, such as intense sunshine, poorly reflecting target surfaces (e.g., black surfaces), or high temperature variations, the deviation over 10m of distance may increase.
Warranty and Support
Warranty
The Mileseey D5T Laser Distance Meter comes with a 12-month warranty and lifetime technical support. Please retain your proof of purchase for warranty claims.
Contact Us
For any concerns or technical assistance, please contact Shenzhen Mileseey Technology Co., LTD. via:
- Website: www.mileseeytools.com
- Email: service@mileseey.com
We strive to reply to your inquiries within 24 hours.
