Introduction
Thank you for choosing einkshop T603XL Refillable Ink Cartridges. These cartridges are designed as a cost-effective and environmentally friendly alternative to single-use cartridges for your compatible Epson printer. They feature Auto Reset Chips (ARC) for seamless integration and easy refilling. Please read this manual carefully to ensure proper installation, refilling, and maintenance for optimal performance.

Image: A set of four einkshop T603XL refillable ink cartridges (Cyan, Yellow, Magenta, Black).
Setup and Installation
- Unpack Cartridges: Carefully remove the refillable cartridges from their packaging. Ensure all protective clips or tapes are removed before installation.
- Initial Fill (Optional but Recommended): While cartridges are shipped empty, you may choose to pre-fill them before the first installation. Refer to the 'Operating Instructions: Refilling' section for detailed steps.
- Prepare Printer: Turn on your Epson printer. Open the printer's ink cartridge access door. The print head will move to the replacement position.
- Remove Old Cartridges: If replacing existing cartridges, gently press the tab on the old cartridge and lift it out.
- Install New Cartridges: Insert each einkshop T603XL cartridge into its corresponding slot (matching colors: Cyan, Magenta, Yellow, Black). Push down firmly until it clicks into place.
- Close Access Door: Close the ink cartridge access door. The printer will perform an initialization cycle.
- Printer Recognition: The printer should recognize the new cartridges. If prompted, confirm that you have installed genuine Epson cartridges (this is a standard prompt for compatible cartridges; proceed). The Auto Reset Chips (ARC) will ensure the printer recognizes the cartridges and displays ink levels correctly, resetting when the cartridge is removed and reinserted.
Operating Instructions: Refilling
These cartridges are designed for easy refilling. Always use high-quality, compatible ink for best results and to prevent printer damage.

Image: A four-panel diagram illustrating the ink cartridge refilling process.
- Prepare for Refill: Remove the cartridge from the printer. Place it on a protected surface (e.g., paper towels) to catch any potential spills.
- Locate Ink Hole: Identify the color plug on the top of the cartridge. This is the ink hole. Carefully take out the color plug.
- Refill Ink: Using a syringe filled with the correct color ink, slowly inject ink into the ink hole.
- Fill Level: Refill the cartridge to approximately 80% capacity. Do not overfill, as this can cause leakage.
- Seal Ink Hole: Once refilled, securely re-install the color plug into the ink hole.
- Locate Air Hole: Identify the yellow label on the cartridge. This covers the air hole. If it's not already open, gently remove or puncture this yellow label to ensure proper air circulation during printing.
- Reinstall Cartridge: Reinsert the refilled cartridge into your printer. The ARC will reset the ink level status.
Maintenance
- Monitor Ink Levels: While the ARC resets, it's good practice to visually inspect cartridges or refill them when print quality starts to degrade, rather than waiting for the printer to indicate empty.
- Regular Printing: Print at least once a week to prevent ink from drying in the print head nozzles.
- Print Head Cleaning: If you notice streaky or faded prints, perform a print head cleaning cycle through your printer's utility software.
- Storage: Store unused ink bottles in a cool, dark place. Keep cartridges installed in the printer to prevent ink from drying out. If removing a cartridge for an extended period, seal the ink and air holes to prevent drying.
Troubleshooting
Printer Not Recognizing Cartridge
- Reinstall: Remove the cartridge and reinsert it firmly until it clicks.
- Clean Contacts: Gently wipe the gold electrical contacts on the cartridge and inside the printer with a lint-free cloth (slightly dampened with distilled water if necessary, then dry thoroughly).
- Printer Reset: Turn off the printer, unplug it from the power source for a few minutes, then plug it back in and turn it on.
Poor Print Quality (Streaks, Fading, Incorrect Colors)
- Check Ink Levels: Ensure cartridges are adequately filled. Refill if necessary.
- Print Head Cleaning: Run the print head cleaning utility from your printer's software. You may need to run it multiple times.
- Nozzle Check: Perform a nozzle check to identify any clogged nozzles and then clean the print head.
- Ink Quality: Ensure you are using high-quality, compatible ink. Low-quality ink can cause print issues.
Ink Leakage
- Do Not Overfill: Ensure you are not filling cartridges beyond 80% capacity.
- Secure Plugs: Make sure the color plug (ink hole) is securely inserted after refilling.
- Air Hole: Ensure the air hole is open but not excessively large, which could cause pressure imbalances.
Specifications
| Product Type | Refillable Ink Cartridge |
| Model Number | 603xl (T603XL) |
| Compatible Brand | Epson |
| Compatible Printer Models | Epson XP-2100, XP-2105, XP-3100, XP-3105, XP-4100, XP-4105, WF-2810, WF-2850 |
| Feature | Compatible, Refillable, Auto Reset Chip (ARC) |
| Cartridge Status | EMPTY (shipped empty, ready for user refill) |
| Bulk Packaging | Yes |
| Brand Name | einkshop |
| Origin | Mainland China |
| High-concerned chemical | None |
User Tips
No specific user tips were available from the provided customer reviews or Q&A data. However, general best practices for refillable cartridges include:
- Always use good quality ink specifically formulated for Epson printers to avoid clogs and ensure vibrant prints.
- Refill cartridges before they are completely empty to prevent air from entering the print head system.
- Keep the printer on (or in standby mode) to allow it to perform automatic maintenance cycles, which helps prevent clogs.
Warranty and Support
For warranty information, technical support, or any issues not covered in this manual, please contact your seller directly. You may also find additional information in the official user manual PDF available at this link.