AnyTone AT-6666 Pro

Contents

AnyTone AT-6666 Pro 10 Meter Radio User Manual

Model: AT-6666 Pro

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your AnyTone AT-6666 Pro 10 Meter Radio. Please read this manual thoroughly before operating the radio to ensure proper use and to maximize its performance and longevity.

AnyTone AT-6666 Pro 10 Meter Radio with microphone, highlighting key features like AM/FM/SSB, 80W power, Echo, NRC, SQ/ASQ, and 7-color LCD.

Figure 1: AnyTone AT-6666 Pro 10 Meter Radio with key features highlighted.

1.1 Key Functions & Features

The AT-6666 Pro offers a wide range of features for optimal communication:

  • LCD display with 7 color options and backlight dimming.
  • Multiple modes: FM, AM, USB, LSB, CW, PA.
  • Frequency Tuning Steps: 10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz.
  • ± 500Hz, 5KHz Clarifier (R/T/R+T selectable).
  • Flexible menu functions and PC programming software.
  • RX and TX NRC Noise Reduction.
  • SQ, ASQ Function (FM and AM mode).
  • RF GAIN Adjustment and RF PWR Adjustment.
  • VFO / BAND / Memory Channel Modes.
  • Repeater Shift / Offset Frequency Function.
  • CTCSS/DCS with RX/TX Split functions.
  • SCAN Function, NB/ANL Function, DW DUAL-WATCH Function.
  • SWR, S/RF meter Function, TOT function, HI-CUT Function.
  • EMG CALL, SWR Protection, Power Supply Voltage Protection.
  • Key-Lock Function, DTMF Function, BEEP Prompt.
  • Enhanced VOX Function (VOX.SPK supports digital mode operation).
  • ECHO Function, Programmable RB Function, AM TX NPC.
  • User Defined (PF) key on microphone, Audio path select, +10KHz Function.
Detailed list of 31 functions and features of the AT-6666 Pro radio.

Figure 2: Comprehensive list of AT-6666 Pro features.

Video 1: Product overview of the AnyTone AT-6666 Pro 10 Meter Radio, showcasing its design and components.

2. Setup

2.1 Standard Accessories

Verify that all standard accessories are included in your package:

  • Radio Unit
  • Microphone
  • Install Bracket
  • Screws
  • Pads
  • Adjusting Screws
  • Microphone Hanger
  • Adhesive Case Protectors
  • Fuse (15A 250V)
  • User Manual (PDF reference available here)
Visual representation of the standard accessories included with the AT-6666 Pro radio.

Figure 3: Standard accessories included with the AT-6666 Pro.

2.2 Installation

Choose a suitable location for the radio, ensuring it does not obstruct the driver or passengers if installed in a vehicle.

  1. Use the Self-tapping Screws and Pads to fix the Bracket to a suitable location.
  2. Attach the Adhesive Case Protectors to the inside ends of the Mounting Bracket and insert the Radio. Fit the Adjusting Screws loosely, and choose a suitable angle by moving the Adjusting Screws to one of the 3 positions on the Mounting Bracket.
  3. Tighten the Adjusting Screws firmly by hand. Ensure the radio and all accessories are securely mounted.

2.3 Antenna Installation

An efficient and resonant antenna is crucial for optimal performance. This radio requires an antenna impedance of 50 ohms, unbalanced.

  1. Screw the antenna connector into the antenna jack.
  2. Grounding of the antenna system is recommended for best performance.

WARNING:

  • NEVER transmit without a connected resonant antenna, or a suitable 50 ohm load. Damage to the radio may result.
  • To reduce the risk of electric shock or radio damage, base station installations should include lightning protection devices.
  • Consult your authorized dealer or service center for antenna options.

2.4 Power Connection

This radio requires a 13.8V (12V) DC power supply. Do not connect to a 24V DC battery system.

  1. Connect the positive (red) power cable to the + terminal of the battery.
  2. Connect the negative (black) power cable to the - terminal of the battery.

IMPORTANT:

  • Locate the power cable away from high temperature, moisture, and other electrical systems. Ensure it is installed where it cannot be damaged.
  • It is not recommended to use a vehicle cigar/cigarette lighter socket to power the radio, as it may not supply the correct voltage or current.
  • Do not remove the fuse holder from the cable.

2.5 Install Microphone Hanger

Choose a location that will not interfere with the driver. Use the supplied self-tapping screws and pads to install the hanger.

2.6 Install External Speaker

If using an external speaker, choose an 8 ohm speaker with a 3.5mm mono (double cable) TS type plug.

  1. Locate the external speaker in a suitable place.
  2. Plug into the speaker jack.
Dimensional drawing of the AT-6666 Pro radio, showing front, side, and rear views with measurements (252mm L, 158mm W, 48mm H).

Figure 4: Dimensions of the AT-6666 Pro radio.

3. Operating Instructions

3.1 Front Panel Controls

Familiarize yourself with the front panel controls:

Close-up of the AnyTone AT-6666 Pro radio's front panel, showing the LCD display and various controls.

Figure 5: Front Panel Layout.

No. Key/Control Function
1FUNCFunction / Menu key
2MODESwitch Mode: FM, AM, USB, LSB, CW, PA
3BANDSwitch Band: A-I / VFO mode
4SCANScan / Scan add / Scan delete
5MEMUse, Store or Delete memory channels
6TSQActivate / deactivate the CTCSS/DCS function
7NRCActivate / deactivate the NRC function
8EMGEmergency Channel; Keypad lock
9PWRRF Power Control
10RFGRF Gain Control
11SQSquelch Control
12CLARSSB/CW Clarifier Control
13VOL/OFFPower On/Off; Volume Control
14CH/PUSHChannel Switch; PUSH key
15RX/TX IndicatorIndicates Receive/Transmit status
16Microphone JackConnection for microphone
17LCD DisplayShows frequency, channel, and status information

3.2 Rear Panel Connections

The rear panel provides essential connections:

  • PC Cable Jack (18): For connecting to a computer for programming.
  • External Speaker Jack (19): For connecting an external speaker.
  • Antenna Jack (20): For connecting the antenna.

3.3 Microphone Functions

The microphone includes several controls:

  • PF (User defined): Programmable function key.
  • DOWN/UP: For navigation or frequency/channel adjustment.
  • PTT: Push-to-Talk button for transmitting.
  • 6-Pin Connector: Connects to the radio unit.

3.4 LCD Display Indicators

The LCD provides visual feedback on the radio's status and settings:

Indicator Description
TXAppears during transmit (TX)
Mode IconsDisplays the working mode (e.g., FM, AM, SSB)
EMGAppears when using Emergency channels
MEMAppears when using Memory channels
ECHOAppears when Echo function is ON
REPAppears when Repeater Offset function is ON
HICAppears when Hi-Cut function is ON
Channel NumberDisplays the channel number
NB/ANLAppears when Noise Blanker / ANL is ON
Band NameDisplays the Band name
10KAppears when +10KHz function is ON
Roger Beep IconAppears when the Roger Beep function is ON
RF MeterDisplay of the TX/RX signal strength
VOX IconAppears when the VOX function is ON
SCAppears when the Scan function is ON
Keypad Lock IconAppears when the Keypad Lock function is ON
RTAppears when the SSB/CW clarifier is enabled
SWRAppears when the SWR level indication is enabled
DWAppears when Dual Watch function is ON
RnrAppears when NRC Noise Reduction function in ON
AQAppears when ASQ is enabled
DCSAppears when DCS is enabled
CTCAppears when CTCSS is enabled
Frequency/Channel InfoDisplays the Frequency and Channel information

3.5 Basic Operation

  • OFF/ON Radio: Turn the VOL knob clockwise to switch ON, anti-clockwise to switch OFF.
  • Volume Control: Turn VOL clockwise to increase, anti-clockwise to decrease.
  • RF Power Control: When transmitting, turn the PWR outer shaft to adjust power. Clockwise increases, anti-clockwise decreases.
  • RF Gain Control: When receiving, turn the RFG inner shaft to adjust gain. Clockwise increases, anti-clockwise decreases.
  • SQUELCH Control: Turn the SQ outer shaft clockwise to adjust squelch level (1-36 levels).
  • SSB Clarifier Control: Turn the CLAR inner shaft to adjust USB/LSB/CW TX or RX frequency.
  • Channel Selection: In channel mode, turn the CH knob to select the desired channel.
  • Frequency Control: In channel mode, press [PUSH] to temporarily adjust VFO frequency. Press [PUSH] again to adjust step size. Turn CH to change frequency.

3.6 Keypad Functions

  • MEM (Memory Channels): Short press MEM to enter/exit memory channel mode. Hold MEM to store/delete channels.
  • ANL/NB (Automatic Noise Limiter/Noise Blanker): Press FUNC + [NB/ANL] to toggle ON/OFF.
  • MODE/DIM (Mode/Dimmer): Short press MODE to cycle through FM-AM-USB-LSB-CW-PA. Press FUNC + MODE to adjust backlight dimmer/brightness.
  • BAND/COLOR (Band/Backlight Color): Short press BAND to cycle through bands A-I. Press FUNC + BAND to change LED backlight color. Long press BAND to activate VFO function.
  • SCAN/DW (Scan/Dual Watch): Short press SCAN to start/stop scan. Long press SCAN to add/delete channels from scan list. Press FUNC + SCAN to toggle Dual Watch (DW) ON/OFF.
  • TSQ/HI-CUT (Tone Squelch/High-Cut Filter): Short press TSQ to toggle CTCSS/DCS ON/OFF. Long press TSQ for CTCSS/DCS settings. Press FUNC + TSQ to toggle HI-CUT ON/OFF.
  • NRC/SPLIT (Noise Reduction/Split Frequency): Short press NRC to toggle RX noise reduction ON/OFF. Press [PTT] + NRC to toggle TX noise reduction ON/OFF. Long press NRC for noise reduction level settings. Press FUNC + NRC to toggle SPLIT function ON/OFF.
  • EMG (Emergency Channel): Short press EMG to use Emergency channel (CH9 or CH19). Long press EMG to lock/unlock keypad.

3.7 Menu Operations

The radio features extensive menu options for customization. To access menus:

  1. Press FUNC (short press for Channel Function Menu, long press for Background Function Menu).
  2. Use the Channel switch to select menu items.
  3. Press [PUSH] to enter/modify a menu item.
  4. Turn the Channel switch to modify options.
  5. Press [PUSH] to confirm and return to the previous menu.

Refer to the full PDF manual for detailed descriptions of all menu items, including Channel Function Menu, Public Data Function Menu, and Background Function Menu.

3.8 Power Output

Image showing the AT-6666 Pro radio and microphone, with a callout for power output: AM 80W(PEP), FM 50W, SSB 80W(PEP).

Figure 6: Power Output Specifications.

  • AM: 80W(PEP)
  • FM: 50W
  • SSB: 80W(PEP)

4. Maintenance

4.1 General Care

  • Keep the radio clean and free from dust and moisture.
  • Avoid exposing the radio to extreme temperatures or direct sunlight for prolonged periods.
  • Do not use harsh chemicals or abrasive cleaners on the radio's surface. Use a soft, damp cloth for cleaning.
  • Ensure proper ventilation around the radio to prevent overheating.

4.2 Replacing Fuse

This radio requires a 15A, 250V fuse. If the fuse blows:

  1. Determine the reason for the blown fuse and correct the problem.
  2. Pull the two fuse covers in opposite directions to open.
  3. Replace the blown fuse with a new 15A, 250V fuse.
  4. Close the fuse holder.

WARNING: Be sure to only use the correct fuse type, otherwise damage may occur.

5. Troubleshooting

If you encounter issues with your radio, try the following basic troubleshooting steps:

  • No Power: Check power cable connections, ensure the fuse is intact, and verify the power supply is providing 13.8V DC.
  • No Transmission/Reception: Ensure the antenna is properly connected and tuned. Check the mode setting (FM, AM, SSB). Verify squelch level is not set too high.
  • Poor Audio Quality: Adjust volume, RF Gain, and Clarifier settings. Check microphone connection.
  • Radio Overheating: Ensure adequate ventilation around the unit. Reduce transmit power if operating for extended periods.
  • Keypad Locked: If the keypad is unresponsive, long press the EMG key to unlock it.

For more complex issues, refer to the detailed troubleshooting section in the full PDF manual or contact customer support.

6. Specifications

General
Frequency Range28.000-29.700MHz (Programmable)
Frequency BandA/B/C/D/E/F/G/H/I + VFO
Channel40 channels (programmable) in each band
Frequency ControlPhase-Locked-Loop Synthesizer
Frequency Step10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz
Frequency Tolerance±5.0 ppm
Temperature Range-20°C ~ +50°C
MicrophoneWith Push-to-Talk / UP / DN / PF and coiled cord
Input Voltage13.8V DC
Dimensions (in mm)252(L) x 158(W) x 48(H)
Weight1.27kg
Antenna ConnectorUHF, SO239
Transmitter
Power OutputAM: 80W(PEP) / FM:50W / SSB: 80W(PEP)
Drain15A (with modulation)
ModulationFM/AM/USB/LSB/CW
Inter-modulation DistortionSSB: 3rd order, more than -25dB; 5th order, more than -35dB
SSB Carrier Suppression55dB
Unwanted Sideband50dB
Frequency ResponseAM/FM: 300 to 3000Hz
SSB: 450 to 2500Hz
Output Impedance50ohms, unbalanced
Receiver
SensitivitySSB: 0.25µV for 10dB(S+N)/N
AM: 1.0µV for 10dB(S+N)/N
FM: 1.0µV for 20 dB (S+N)/N
(All at greater than 1/2 watt of audio output)
Adjacent-Channel SelectivityAM/FM: 60dB SSB: 70dB
Image RejectionMore than 65dB
IF FrequencyAM/FM: 10.695MHz 1st IF, 455KHz 2nd IF
SSB: 10.695MHz
RF Gain Control45dB adjustable for optimum signal reception
Automatic Gain Control(AGC)Less than 10dB change in audio output for inputs from 10 to 100,000 microvolt.
SquelchAdjustable; threshold less than 1.0µV.
Automatic Squelch Control (AM/FM) 1.0µV
Audio Output Power3 watts into 8 ohms
Frequency ResponseAM/FM: 300 to 3000Hz SSB: 450 to 2500Hz
Built-in Speaker8 ohms, round.
External Speaker(Not Supplied)8 ohms; disables internal speaker when connected.

7. User Tips

  • Antenna Tuning: Always ensure your antenna is properly tuned for the operating frequency to prevent damage to the radio and ensure maximum performance.
  • Power Supply Stability: Use a stable 13.8V DC power supply capable of providing sufficient current (15A) to avoid performance issues, especially during high-power transmissions.
  • Noise Reduction: Experiment with the NRC (Noise Reduction) and NB/ANL (Noise Blanker/Automatic Noise Limiter) functions to find the optimal settings for your operating environment to improve signal clarity.
  • Memory Channels: Utilize the 40 programmable memory channels to quickly access frequently used frequencies and settings.
  • PC Programming: For advanced customization and fine-tuning of settings, use the PC programming software. This allows for more detailed control over various radio parameters.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official AnyTone website or contact your authorized dealer.

Official Website: www.anytone.net

A comprehensive user manual in PDF format is available for download: AnyTone AT-6666 Pro User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.