1. Introduction
Thank you for purchasing the M8AC balance charger. Please read this manual carefully before use to ensure proper operation and safety.
Key Points:
- 💡 Tips: Helpful advice for optimal use.
- ❗ Important: Critical information for safety and functionality.
- 📄 Information: General details and explanations.
For further information, including news, firmware updates, and support, please visit the official ToolkitRC website: www.toolkitrc.com
2. Safety Information
❗ WARNING: Failure to follow these safety instructions may result in fire, property damage, or injury.
- The M8AC charger supports an input voltage of DC 7-35V or AC 100-240V. Ensure the charger is only connected to a suitable power source with correct polarity.
- Do not use this product in hot, humid, flammable, or explosive environments.
- Always supervise the charger when in use. Never leave charging batteries unattended.
- When not in use, unplug the input power from the charger.
- When using the charging function, set a current that matches the battery's specifications. Avoid excessive current to prevent battery damage. Always refer to your battery manufacturer's guidelines for correct charging instructions.
3. Product Overview
The ToolkitRC M8AC is a versatile multifunctional tool designed for RC enthusiasts. It integrates a balance charger, discharger, signal measuring device, and signal source into one compact unit.
Key Features:
- Dual Input: Supports both AC (100-240V) and DC (7-35V) power input.
- Wide Battery Compatibility: Charges, discharges, and balances LiPo, LiHV, LiFe, Lilon, LTO (1-8S), NiMH (1-20S), and PB (1-12S) batteries.
- High Power Output: Max charge current 20A @ 600W (DC) / 200W (AC).
- Discharge Modes: Recycle discharge up to 20A @ 600W, internal discharge up to 3A @ 20W.
- USB-C PD Output: 65W (20V) for fast charging mobile devices.
- Adjustable Cut-off Voltage: Lithium battery cut-off voltage (TVC function) is user-adjustable.
- Battery Analysis: Measures battery voltage, internal resistance, and automatically balances lithium packs.
- Signal Functions: Measures and outputs PWM/PPM/SBUS standard signals with 1µs accuracy.
- Adjustable Power Supply: Constant current and constant voltage source output (1-35V, 0.5-20A).
- Drone Battery Charging: Adaptable for charging consumer-grade drone batteries.
- User Interface: Multi-language support and easily upgradable via USB.

Figure 3.1: ToolkitRC M8AC Smart Charger front view with display showing charging parameters.
Video 3.1: Official product overview demonstrating features and ports of the M8AC charger.
4. Setup
4.1 M8AC Layout

Figure 4.1: ToolkitRC M8AC Smart Charger showing side view with output ports and rear view with AC/DC input.
Front Panel:
- Display: 2.4-inch IPS LCD screen.
- Exit Button: For navigating menus and exiting functions.
- Output Port: Main XT60 output for charging/discharging.
- Balance Port: For 1-8S battery balancing.
- Signal Port: For PWM/PPM/SBUS signal measurement and output.
- TYPE-C Output: USB-C port for PD fast charging.
- Scroll Wheel: For menu navigation and parameter adjustment.
Rear Panel:
- AC Input: For 100-240V AC power supply.
- DC Input: For 7-35V DC power supply (XT60 connector).
- Cooling Fan: Automatically activates to dissipate heat.
4.2 Quick Start Guide
- Connect Power: Connect a 7-35V DC power supply (via XT60) or an AC 100-240V power supply to the corresponding input port on the back of the M8AC.
- Power On: The display will show the boot logo for 2 seconds, accompanied by a welcome sound.
- Main Interface: After booting, the screen will enter the main interface, displaying current status (e.g., input voltage, temperature, standby).
- Auxiliary Functions: Press and hold the [Exit] button to enter the auxiliary function interface.
- Navigation: Rotate the [Scroll Wheel] to switch between pages or options.
- Parameter Adjustment: When the charger is idle, short press the [Scroll Wheel] to set charging parameters. During charging, short press to adjust amperage or stop the process.
- System Settings: When idle, press and hold the [Scroll Wheel] to enter the system settings interface.
- Return: Short press [Exit] to return to the previous interface.
5. Operating Instructions
5.1 Charge and Discharge Settings
From the main interface, select and short press the [Scroll Wheel] to enter the charging function. Ensure the battery selection option is enabled in system settings.
5.1.1 Battery Type Setting
- Rotate the [Scroll Wheel] to select an existing battery profile or create a new one (up to 32 profiles).
- Short press the [Scroll Wheel] to enter specific battery settings.
- Navigate to [Battery Type] and short press the [Scroll Wheel] to modify the battery chemistry. Supported types: LiPo, LiHV, LiFe, Lilon, LTO, NiMH, PB.
- After selecting, short press the [Scroll Wheel] and [Exit] to save and return.
❗ Warning: Always ensure the correct battery type is selected before charging. Incorrect selection can damage the battery or cause a fire hazard. Do not charge incompatible battery chemistries.
5.1.2 Cell Setting
- Navigate to [Cells] and short press the [Scroll Wheel] to modify the number of cells.
- Rotate the [Scroll Wheel] to adjust the value (e.g., 1S, 2S, 3S...).
- If set to [Auto], the charger will automatically detect the cell count via the balance port.
- Short press the [Scroll Wheel] and [Exit] to save.
💡 Tips: If a battery is over-discharged or over-charged, auto-detection might be inaccurate; manually adjust the cell count. Incorrect cell count can lead to overcharging and fire risk. Connecting the balance port improves accuracy.
5.1.3 Work Mode
- Navigate to [Mode] and short press the [Scroll Wheel] to select the desired work mode:
- Charge: Standard charging.
- DisCHG: Discharge.
- StoCHG: Storage charge.
- LiPo, LiHV, LiFe, Lilon, LTO batteries can be charged, discharged, or stored. NiMH and PB batteries can be charged or discharged.
- Short press the [Scroll Wheel] and [Exit] to save.
5.1.4 Discharge Mode
When in discharge, storage, or cycle modes, the discharge option appears.
- Navigate to [Discharge Mode] and short press the [Scroll Wheel] to select:
- Inter (Internal): Uses internal heat dissipation, max 3.0A @ 20W.
- Recycle: Recovers power to the input battery, max 20.0A @ 600W. To activate Recycle mode, set the Power type under input settings to "Battery" in the setup page.
5.1.5 Max Input Voltage (for Recycle Discharge)
- When Recycle discharge is selected, navigate to [Max Input Vol.] and adjust the voltage.
- If the input voltage reaches this value during discharge, the process will stop.
💡 Tips: Set this to the highest safe protection voltage of your power supply. Setting it too high can damage the input power source.
5.1.6 End Voltage Setting (TVC)
- Navigate to [End Voltage] and short press the [Scroll Wheel] to modify the individual cell end voltage.
- This is the charge cut-off voltage (±50mV of full voltage) or discharge cut-off voltage. Adjust in 0.01V increments.
💡 Tips: Only LiPo, LiHV, LiFe batteries support TVC. Do not modify if unfamiliar with battery characteristics.
5.1.7 Current Setting
- Navigate to [Charge Current] or [DisCHG Current] and short press the [Scroll Wheel].
- Rotate the [Scroll Wheel] to adjust the current (0.1A steps). The charger supports up to 20.0A.
💡 Tips: Set charge rate to 1-2C (e.g., 2000mAh battery = 2.0-4.0A). Current settings are only valid for the corresponding work mode.
5.1.8 NiMH Setting (PeakV)
When NiMH battery type is selected, you can set the peak voltage value (5mV-15mV) at which the battery is considered fully charged.
5.1.9 Cycle Setting (for NiMH)
When NiMH is selected and in cycle mode, options for [Cycle times] (2-12) and [Rest time] (2-10 minutes) appear. The charger follows a discharge-charge pattern.
5.1.10 Smart Battery Setting (UAV)
For UAV battery type, you can select [Drone model] (e.g., Mavic2, Phantom) and set [Max Current] (0.5A-20A).
5.2 Charge and Discharge Operation
- Once charging/discharging starts, the display shows real-time data: input voltage, accumulated power, internal temperature, main port voltage/current, working time, and charged capacity.
- Rotate the [Scroll Wheel] to toggle between different display screens (e.g., internal resistance).
- Short press the [Scroll Wheel] to dynamically adjust charge current or stop the process.
- Upon completion or error, a popup and audible tone will occur.
💡 Tips: Never leave cells unattended. For lithium batteries, balancing only occurs if the balance plug is connected. The charger will automatically balance each cell if detected. Charging will automatically start for the next battery if the initial battery is disconnected after being fully charged, provided cell count matches.
5.3 Auxiliary Functions (Accessibility)
Long press [Exit] from the main interface to access:
- Measure Resistance: Tests internal resistance of connected battery.
- Measure Signal: Measures PWM, PPM, or SBUS signals.
- Signal Output: Outputs PWM, PPM, or SBUS signals (manual or auto modes).
- ESC Test: Tests Electronic Speed Controllers (ESC) with adjustable pulse width/cycle.
- Power: Adjustable power supply output (voltage and current).
6. System Settings
Press and hold the [Scroll Wheel] from the main interface to enter system settings.
6.1 Input Settings
- Power Select: Preset power profiles.
- Power Type: Choose between Battery Pack (enables recycle mode) or Adapter (disables recycle mode).
- Max Power: Maximum wattage allowed via input port.
- Max Current: Maximum current allowed via input port.
- Voltage Range: Input voltage range.
6.2 Security Settings
- Safe Inter Temp.: Charging stops if internal temperature exceeds this value.
- Safe Exter Temp.: Charging stops if ambient temperature exceeds this value.
- Safe Time: Maximum continuous charging/discharging time.
- Safe Capacity: Maximum accumulated capacity for a session.
6.3 Personalization
- Backlight: Display brightness (1-10).
- Operation Volume: Beep volume (0-10, 0 for silent).
- Language: System display language (English, Chinese, etc.).
- Theme Style: Light or dark themes.
6.4 Other Settings
- Battery Selection: Show/hide frequently used parameters.
- Continuous Work: Enables/disables continuous charging/discharge after battery replacement.
- Work Completed: Stop or trickle charge after completion.
- Balance Start Vol: Balance cells prior to full current charge.
- Default: Restore factory settings.
- ID: Independent ID for each device.
7. Other Functions
- Firmware Upgrade: Connect M8AC to a computer via USB. It will appear as a USB drive named 'Toolkit'. Download 'app.upg' from the ToolkitRC website and overwrite the file on the drive to upgrade.
- TYPE-C Output: Provides 20.0V 65W output for charging mobile devices.
- Automatic Continue Charging/Discharging: If enabled in settings, the device will automatically continue the process with the next battery after one is fully charged.
- Fan Control: Fan activates at 40°C, speed increases with temperature. At AC input >100W, the fan runs at full speed.
- Manual Voltage Calibration: With M8AC off, press and hold the [Scroll Wheel], then connect power. Use a voltmeter to measure actual cell voltages and adjust corresponding values on the charger. Save to complete.
- Full Charge Mode: For lithium batteries,