1. Introduction
Thank you for choosing the PERLESMITH Universal TV Bracket Model 905. This table-top TV stand is designed to securely hold televisions ranging from 26 to 55 inches, offering adjustable height and a sturdy tempered glass base. Please read this manual carefully before installation and use to ensure safe and correct operation.
Figure 1: PERLESMITH TV Bracket Model 905 with key dimensions and features.
2. Package Contents
Before installation, please check that all parts are present and undamaged. If any parts are missing or damaged, please contact your supplier for assistance.
Product Accessories List:
| Part | Description | Quantity |
|---|---|---|
| A1 | M8*55 Screw | 4 |
| A2 | M8 Flange Nut | 4 |
| B1 | 5MM Height Increasing Pads | 4 |
| B2 | 5MM Rubber Pad | 4 |
| C1 | Dust Cover | 1 |
| C2 | Under Pipe | 1 |
| D | M8*30 Screw | 3 |
| E | M6*16 Screw | 4 |
| M5*16 Screw | 4 | |
| F | 6MM Flat Washer | 4 |
| G | 8MM Flat Washer | 4 |
| H | 5*35 Screw | 2 |
| I | Explosion-proof Iron Sheet | 1 |
3. Setup and Installation
Follow these steps carefully to assemble your TV bracket. It is recommended to have a second person assist during the final mounting of the TV.
Figure 2: Visual guide for installation steps and parts.
- Step 1: Prepare the Glass Base
- Peel off the adhesive pad stickers (B2) and attach them to the glass base.
- Stick the four corners of the rubber pads to the back of the glass base.
- Step 2: Attach the Column to the Base
- Connect part C2 (the pipe under the sheet) to the column, ensuring it is fixed to the front of the glass base.
- Note: Align the column properly before tightening the column screws. Tighten the screws only after the vertical glass is level.
- Use screw D to pass through part I (explosion-proof iron sheet) and then through the glass base to secure the column.
- Step 3: Assemble the TV Plate and Column
- Install C1 (dust cover) at the top of the column. Tighten the nut (A2) again.
- Use screws A1 to pass through the TV panel, column, and nut (A2). Do not fully tighten the nut yet.
- Note: Before fully tightening the nut, place the dust cover (C1) over the top of the column. Then tighten the nut after covering it.
- Step 4: Attach TV Hooks (Optional Heightening)
- The screw model from group E (M6*16 or M5*16) can be used according to your TV's requirements.
- You can install the TV heightening pads (B1) between the hook and the TV (Figure A) or above the hook (Figure B) if needed. This step is optional.
- Step 5: Mount the TV
- Carefully mount your TV onto the assembled panel and secure the TV hooks onto the bracket.
- Fix the safety screws (H) to the hooks to prevent accidental dislodging.
- The installation is now complete.
4. Operating Instructions
Height Adjustment
The PERLESMITH Model 905 TV bracket features a 3-speed height adjustment mechanism, allowing you to customize the viewing height of your television. The stand offers a height range of 68cm down to 55cm, with each step adjusting by approximately 4cm.
- To adjust the height, carefully lift the TV slightly and reposition the TV hooks to the desired slot on the vertical bracket.
- Ensure both TV hooks are set to the same height level for a balanced and secure display.
- Always ensure the safety screws (H) are re-secured after any height adjustment.
Figure 3: Illustration of 3-step height adjustment for TV hooks and plate.
Figure 4: The extended column allows for flexible height adjustments.
5. Maintenance
To ensure the longevity and appearance of your TV bracket, follow these simple maintenance guidelines:
- Cleaning: Use a soft, dry cloth to wipe down the metal and glass surfaces. For stubborn marks, a slightly damp cloth with mild soap can be used, followed by drying thoroughly. Avoid abrasive cleaners or solvents.
- Inspection: Periodically check all screws and connections to ensure they remain tight and secure. Re-tighten if necessary.
- Weight Limit: Do not exceed the maximum load weight of 40kg (88 lbs).
6. Troubleshooting
If you encounter any issues with your TV bracket, consider the following:
- Stand is Unstable:
- Ensure all screws are fully tightened according to the installation instructions.
- Verify that the TV's weight and VESA pattern are within the specified limits.
- Place the stand on a flat, level surface.
- TV Not Level:
- Check that both TV hooks are installed at the exact same height on the vertical bracket.
- Ensure the base is on a level surface.
- Difficulty Adjusting Height:
- Ensure the TV is slightly lifted to relieve pressure on the hooks before attempting to reposition them.
- Do not force the adjustment; if it feels stuck, re-check the alignment.
If problems persist, please refer to the warranty and support section.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | 905 |
| Installation Type | Table Top |
| Compatible TV Sizes | 26 - 55 inches |
| Maximum Load Weight | 40 kg (88 lbs) |
| Standard VESA Compatibility | 100x100, 200x100, 200x200, 300x200, 300x300, 400x300, 400x400 mm |
| Height Adjustment | Yes, 3-speed (68cm to 55cm, 4cm per step) |
| Base Material | Tempered Glass |
| Total Height (Max) | 680 mm (26.77 in) |
| Base Dimensions (W x D) | 432 mm (17 in) x 240 mm (9.45 in) |
| Bracket Width | 460 mm (18.11 in) |
| Package Dimensions (L x W x H) | 54 cm x 29 cm x 9 cm |
| Package Weight | 4.28 kg |
| Origin | Mainland China |
8. User Tips
No specific user tips were available from customer reviews or Q&A for this product at the time of manual creation.
9. Warranty and Support
For warranty information, technical support, or if you have any questions regarding the installation or operation of your PERLESMITH Universal TV Bracket Model 905, please contact the seller or retailer from whom you purchased the product. Please have your purchase details and model number (905) ready when contacting support.
An additional user manual in PDF format may be available for download from the product's listing page or by contacting the seller directly: View User Manual (PDF)