1. Product Overview
This manual provides instructions for the FD 433.92MHz Rolling Code Garage Door Remote Control, designed for use with compatible garage door openers. This remote control is part of the 'FloR' line, utilizing advanced rolling code technology for enhanced security.
Key Features:
- Frequency: 433.92 MHz
- Encoding Method: Rolling Code (FloR 52-bit)
- Buttons: Available in 2-button (FLO2R-S) and 4-button (FLO4R-S) configurations
- Power: 12V DC, powered by a type 23A battery
- Compatibility: Designed for garage door openers that support 433.92MHz rolling code remotes
Figure 1: FD Garage Remote Control Models FLO2R-S (2-button) and FLO4R-S (4-button)
2. Setup and Programming
2.1 Initial Check
- Press any button on the remote control.
- Observe the LED indicator on the remote. It should flash, indicating that the remote is transmitting a signal and the battery is functional.
2.2 Programming the Remote
This remote control uses rolling code technology (FloR type), which means it cannot be programmed by copying from another remote or by setting DIP switches on the remote itself. It must be programmed directly to your garage door opener's receiver.
Important: Always refer to your specific garage door opener's instruction manual for detailed programming steps. The procedure varies depending on the opener model.
Generally, the programming process involves:
- Locating the 'Learn' or 'Program' button on your garage door opener's motor unit.
- Pressing the 'Learn' button (often for a short duration, e.g., 1-2 seconds).
- Within a specified timeframe (usually 30 seconds), pressing the desired button on your new FD remote control.
- The opener's light may flash or click to confirm successful programming.
Figure 2: FLO2R-S (2-Button Model)
Figure 3: FLO4R-S (4-Button Model)
3. Operating Instructions
Once programmed, operate your garage door by simply pressing the corresponding button on the remote control. The remote will send a signal to your opener's receiver, activating the door.
- Range: The effective operating range is approximately 100-200 meters in open outdoor areas and up to 35 meters indoors, depending on environmental factors and obstructions.
4. Maintenance
4.1 Battery Replacement
The remote control's operating range and the brightness of its LED indicator will decrease when the battery is low. Replace the battery to restore normal function.
Battery Type: 12V DC, type 23A battery.
Procedure:
- Carefully open the remote control casing (refer to your remote's specific design for opening points, usually a small notch or screw).
- Remove the old 23A battery.
- Insert a new 12V DC type 23A battery, ensuring correct polarity (+ and - terminals are aligned as indicated inside the battery compartment).
- Close the remote control casing securely.
4.2 Battery Disposal
Used batteries contain polluting substances and must not be discarded with household waste. Please dispose of them according to local regulations for separated collection of hazardous waste. Look for designated battery recycling points in your area.
5. Troubleshooting
- Remote Not Working:
- Check if the LED flashes when a button is pressed. If not, replace the battery.
- Ensure the remote is correctly programmed to your garage door opener's receiver. Refer to your opener's manual and Section 2.2 of this manual.
- Verify that your garage door opener is powered on and functioning correctly.
- Reduced Operating Range or Dim LED:
- This is typically an indication of a low battery. Replace the 12V DC type 23A battery.
6. Specifications
| Feature | Specification |
|---|---|
| Frequency | 433.92 MHz (±100 KHz) |
| Encoding Method | Rolling Code (FloR 52-bit) |
| Power Supply | 12V DC (Type 23A battery) |
| Battery Life (Approx.) | 1 year (based on 10 transmissions per day) |
| Operating Range | 100-200 m (outdoor), up to 35 m (indoor) |
| Operating Temperature | -20°C to +55°C |
| Dimensions (L x W x H) | 73 x 40 x 15 mm |
| Weight | 14 g |
| Certification | CE |
7. User Tips
- Always Consult Your Opener's Manual: For programming and compatibility, your garage door opener's manual is the primary resource.
- Verify Compatibility: Before attempting to program, ensure your garage door opener is compatible with 433.92MHz rolling code remotes.
- Keep Spare Batteries: It's advisable to keep a spare 12V DC type 23A battery on hand to avoid unexpected interruptions.
8. Frequently Asked Questions (FAQ)
- Q: Is this remote compatible with my garage door opener model X?
- A: This remote operates on 433.92MHz with rolling code technology. Please consult your garage door opener's manual or its manufacturer's specifications to confirm compatibility with these details.
- Q: Can I clone this remote from my original remote?
- A: No, this is a rolling code remote. It must be programmed directly to your garage door opener's receiver, not cloned from another remote. Refer to your opener's manual for programming instructions.
- Q: Does this remote use DIP switches (e.g., 10-pin code)?
- A: No, this remote uses rolling code technology and does not have DIP switches for coding. DIP switches are typically found on older fixed-code remotes.
9. Warranty and Support
For any issues, technical support, or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.