TEYUN Q24

Contents

TEYUN Q24 Audio Interface User Manual

24bit/192KHz 2-Channel Sound Card for Studio Recording and Live Monitoring

1. Introduction

This manual provides detailed instructions for the TEYUN Q24 Audio Interface, a professional 24-bit/192KHz 2-channel sound card designed for high-fidelity audio recording and monitoring. It is ideal for electric guitar, live recording, studio use, and singing applications. Please read this manual thoroughly to ensure proper use and to keep it for future reference.

2. Safety Information

  • Do not expose the device to rain, moisture, or extreme temperatures.
  • Avoid placing the device near heat sources or in direct sunlight.
  • Do not open the casing; refer all servicing to qualified personnel.
  • Ensure proper ventilation around the device.
  • Always use the specified power supply (USB 2.0 or 5V DC adapter).
  • To prevent loud noises and potential equipment damage, always turn down output levels before connecting or disconnecting cables, especially when engaging/disengaging phantom power or the HI-Z switch.

3. Package Contents

Please check that all items are present in the package:

  • TEYUN Q24 Audio Interface
  • USB Cable
  • User Manual (this document)
TEYUN Q24 Audio Interface with included USB cable
Image: TEYUN Q24 Audio Interface and its USB cable.

Note: A USB power adapter or USB mobile battery is not included and may be required for certain setups.

4. Product Overview

4.1. Front Panel Controls

Front panel of TEYUN Q24 Audio Interface with labeled controls
Image: Front panel of the TEYUN Q24 Audio Interface, showing all knobs, switches, and input jacks.
  1. GAIN 1 Knob: Adjusts the input level for Channel 1. Set so the PEAK LED (2) flashes briefly at maximum volume.
  2. MIC/LINE 1 PEAK Indicator: Lights up when the input signal is too high (within 3dB of clipping). Adjust GAIN 1 to prevent constant illumination.
  3. MIC/LINE 1 SIG Indicator: Lights up when an input signal is detected. If not lit, increase GAIN 1.
  4. INPUT 1 HI-Z Switch: Engages high-impedance mode for instruments like electric guitars/basses connected to INPUT 1. Use with unbalanced phone plugs.
  5. MIC/LINE 1 Jack: Combo jack for microphones (XLR) or line-level instruments (TRS/TS).
  6. STEREO/MONO Switch: When pressed, signals from both MIC/LINE 1 and 2 are output to both L/R channels of MAIN OUTPUTS and PHONES.
  7. MIC/LINE 2 Jack: Combo jack for microphones (XLR) or line-level instruments (TRS/TS). Phantom power is supplied via XLR.
  8. MIC/LINE 2 PEAK Indicator: Lights up when the input signal is too high (within 2dB of clipping). Adjust GAIN 2 to prevent constant illumination.
  9. MIC/LINE 2 SIG Indicator: Lights up when an input signal is detected. If not lit, increase GAIN 2.
  10. GAIN 2 Knob: Adjusts the input level for Channel 2. Set so the PEAK LED (8) flashes briefly at maximum volume.
  11. MIX Knob: Balances the output signal between direct input monitoring (INPUT) and playback from your computer (DAW). Turn towards DAW for more playback, towards INPUT for more direct monitoring.
  12. LOOPBACK Button: Enables internal routing of audio from your computer back into the interface for recording or live streaming.
  13. OUTPUT Knob: Controls the overall output level of the MAIN OUTPUTS.
  14. POWER Indicator: Lights when powered on. Flashes if power is insufficient.
  15. +48V Indicator: Lights when +48V phantom power is active.
  16. HEADPHONE Jack: 1/4" stereo jack for connecting headphones.
  17. PHONES Knob: Adjusts the output level for the HEADPHONE Jack.

4.2. Rear Panel Connections

Rear panel of TEYUN Q24 Audio Interface with labeled connections
Image: Rear panel of the TEYUN Q24 Audio Interface, showing power, USB, and output connections.
  1. High Speed USB 2.0 Port: Connects the interface to your computer or iOS device for data and power.
  2. Transfer Switch: Selects power source: [USB 2.0] for bus power from PC, or [5V DC] for external power adapter.
  3. 5V DC Port: Connects to an external 5V DC power adapter or USB mobile battery (not included) for additional power.
  4. +48V Switch: Activates/deactivates +48V phantom power for XLR microphones connected to MIC/LINE 1/2 jacks.
  5. GROUND: Grounding point to reduce noise/hum when connected to other equipment.
  6. LINE INPUTS (L/R) Jacks: RCA jacks for connecting external stereo audio equipment.
  7. LINE OUTPUT (L/R) Jacks: RCA jacks for connecting external stereo output devices like monitor speakers.
  8. MAIN OUTPUTS (L/R) Jacks: 1/4" TRS/TS jacks for main stereo output to monitor speakers.

5. Setup Instructions

5.1. Connecting to a Computer

  1. Ensure all output level controllers on the Q24 are set to minimum.
  2. Connect the Q24 to your computer using the provided USB 2.0 cable via the High Speed USB 2.0 Port (18).
  3. Set the Transfer Switch (19) to [USB 2.0] for bus power. If additional power is needed, set it to [5V DC] and connect an external 5V DC power source to the 5V DC Port (20).
  4. Wait at least 6 seconds after connecting the USB cable before proceeding.
  5. The Q24 is driver-free for Windows 7/8/10/11 and Mac OS.
TEYUN Q24 connected to a laptop via USB
Image: The TEYUN Q24 Audio Interface connected to a laptop via USB.

5.2. Connecting Instruments and Microphones

Diagram showing various input connections to the TEYUN Q24
Image: Connection diagram for microphones, guitars, and keyboards to the Q24's input channels.
  • Microphones: Connect XLR microphones to MIC/LINE 1 (5) or MIC/LINE 2 (7) jacks. If using condenser microphones, activate +48V phantom power using the +48V Switch (21).
  • Electric Guitar/Bass: Connect directly to MIC/LINE 1 (5) using a TS cable. Engage the INPUT 1 HI-Z Switch (4).
  • Keyboards/Line-level Instruments: Connect to MIC/LINE 1 (5) or MIC/LINE 2 (7) using TRS/TS cables, or use the LINE INPUTS (23) for RCA connections.

5.3. Connecting Monitors and Headphones

Diagram showing output connections from TEYUN Q24 to monitors and mobile devices
Image: Connection diagram for studio monitors and mobile devices to the Q24's output and input.
  • Studio Monitors: Connect your monitors to the MAIN OUTPUTS (25) using 1/4" TRS/TS cables, or to the LINE OUTPUT (24) using RCA cables.
  • Headphones: Connect headphones to the HEADPHONE Jack (16).

5.4. Computer Settings (Windows)

For driver-free installation on Windows 7/8/10/11:

  1. Disable Return to Listening: In the PC volume mixer, ensure "return to listening" is turned off to prevent repetitive sound and distortion.
  2. Playback Settings:
    • Locate the TEYUN Q24 device in your sound settings.
    • Set the sample rate and bit depth. Choose appropriate settings based on your PC's hardware capabilities to avoid improper operation.
  3. Recording Settings:
    • Locate the TEYUN Q24 device in your sound settings.
    • Set the sample rate and bit depth. Choose appropriate settings based on your PC's hardware capabilities to avoid improper operation.

If you require ASIO support, you can install [ASIO4ALL].

6. Operating Instructions

  • Adjusting Input Levels (GAIN, PEAK, SIG): Use the GAIN knobs (1, 10) to set input levels. Aim for the PEAK indicators (2, 8) to flash only briefly at the loudest parts of your performance. The SIG indicators (3, 9) should be consistently lit when a signal is present.
  • Using HI-Z (4): Engage this switch when connecting high-impedance instruments like electric guitars directly to INPUT 1. Remember to turn down monitor speakers before switching to avoid loud noises.
  • STEREO/MONO (6): Press this switch to combine inputs 1 and 2 into a mono signal, outputting to both L/R channels.
  • Monitoring with MIX Knob (11):
    • DAW Side: Prioritizes playback from your computer.
    • INPUT Side: Prioritizes direct monitoring of your input signal with minimal latency.
  • LOOPBACK Function (12): Activate for streaming or recording computer audio alongside your live inputs.
  • Output Levels (OUTPUT, PHONES): Use the OUTPUT knob (13) to control main monitor volume and the PHONES knob (17) for headphone volume.
  • Phantom Power (+48V): Activate the +48V Switch (21) only when using condenser microphones that require phantom power. Ensure all output levels are at minimum before engaging or disengaging.
  • Grounding (22): If you experience hum or noise, connect a clean earth wire to the GROUND point to reduce interference.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use liquid cleaners or solvents.
  • Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
  • Cable Care: Avoid bending or crimping cables excessively. Disconnect cables by pulling the plug, not the cable itself.

8. Troubleshooting

8.1. Power Issues

  • Power indicator is off:
    • Check if the USB cable is correctly connected.
    • Ensure the Transfer Switch (19) is set correctly (USB 2.0 for bus power, 5V DC for external adapter).
    • If using an external adapter, ensure it's a 5V DC adapter with at least 0.9A output.
  • Power indicator blinks continuously:
    • This indicates insufficient power. Switch to 5V DC power mode and use an external USB power adapter or mobile battery.

8.2. No Sound

  • Cable Connections: Verify all audio cables (inputs, outputs, headphones) are securely connected.
  • Volume Levels: Check the GAIN knobs (1, 10), OUTPUT knob (13), and PHONES knob (17) are not set to minimum.
  • Monitor Speakers: Ensure your monitor speakers are powered on and their volume is up.
  • Computer Settings: Verify the TEYUN Q24 is selected as the default playback and recording device in your computer's sound settings. Check sample rate and bit depth settings.
  • HI-Z Switch: If using a guitar, ensure the HI-Z switch (4) is engaged.
  • Phantom Power: If using a condenser mic, ensure +48V phantom power is activated.

8.3. Abnormal Sound (Noise, Interruption, Distortion)

  • System Requirements: Ensure your computer meets the system requirements for audio processing. An older PC might struggle with high sample rates.
  • Recording Level: Check for input clipping (PEAK indicators constantly lit). Reduce GAIN to prevent distortion. Recommended recording level is 0dB (0dB IV).
  • Grounding: If experiencing hum, connect a ground wire to the GROUND point (22).
  • USB Cable: Use the provided USB cable. A faulty or incorrect USB cable can cause issues.
  • Computer Load: Close unnecessary applications to free up CPU resources, especially when recording long audio tracks.
  • Microphone Connection: Ensure XLR microphones are connected with XLR plugs. If using a phone plug for a microphone, the volume might be insufficient (TRS is for LINE input).

9. Technical Specifications

Feature Specification
Type Mixers (Audio Interface)
Model Number Q24
Built-in Battery No
Certification CE
MIC INPUT 1-2 (balanced)
Frequency response -1/-1dB, 20Hz-20kHz
Dynamic Range 82 dB, A weighting
THD-N 0.03%, 1kHz
Maximum input level +6dBu
Input resistance 4kΩ
Gain range +30dB - +60dB
HI-Z INPUT 2 (Unbalanced)
Maximum input level +3.0dBV
Input resistance 1 MΩ
Gain range 0dB - +40dB
LINE INPUT 3 (balance)
Input resistance 18.5kΩ
Gain range -10dB - +40dB
Maximum input level +10dBu
MAIN OUTPUT (Impedance balance)
Frequency response -1/-1dB, 20Hz-20kHz
Dynamic Range 82 dB, A weighting
THD-N 0.03%, 1kHz
Maximum output level +6dBu
Output resistance 100Ω
PHONES
Maximum input level 15mW + 15mW, 40Ω
USB Full speed USB 2.0, 24-bit, 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz
XLR INPUT Polarity 1: Grounding, 2: Hot wire (+), 3: Cold wire (-)
Power requirements >5W

10. User Tips

  • For optimal recording quality, always monitor your input levels carefully using the PEAK indicators to avoid clipping.
  • Experiment with the MIX knob to find the perfect balance between direct monitoring and DAW playback for your workflow.
  • If you experience latency during recording, try reducing the buffer size in your DAW's audio settings.
  • When using the LOOPBACK function for streaming, ensure your computer's audio output is routed correctly to avoid feedback loops.

11. Warranty and Support

For detailed warranty information and further technical support, please refer to the official documentation provided by TEYUN. A comprehensive user manual in PDF format is available for download:

View User Manual (PDF)

Please retain your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.