1. Introduction
Thanks for purchasing the X6 HUD. This HUD is designed to reflect your vehicle's computer information onto your windshield, offering a safer driving experience day to day, especially at high speeds and during night driving. It removes the need for the driver to dip their head to view the instrument cluster. Installing this unit correctly will enable you to more effectively monitor your speed, which is helpful for novice drivers as well as experienced drivers in potentially avoiding speeding infringements.
The X6 HUD uses up-to-date technology throughout its hardware and software, as well as an aesthetic design boasting a unique and elegant shape. To ensure your unit is set up and functioning properly, it is crucial you read and follow this user manual's setup procedures.
2. Setup and Installation
2.1. HUD Installation Procedure
- Ensure your vehicle is OBDII compatible or EUOBD.
- Check around the area under the steering wheel for an OBD plug.
- Contact your vehicle manufacturer or search online.
- Open the bonnet and look for an OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn't a deciding factor).
- Locate the 16-pin diagnostic link. This is usually located in the area under the steering wheel.
- Start vehicle's engine and ensure the power switch is in the on position.
- HUD will power on with the engine.
- If the HUD displays vehicle voltage, fuel consumption, speed, and rotational speed, the unit has installed correctly.
- Failing the above: Wait up to one minute for software to sync and confirm the OBD cable is plugged in properly.


2.2. Reflective Film Installation
Using the unit without the reflective film may result in a double image observed by the user, depending on the windshield. If you see a double layer, it is due to the windshield's dual-layer construction, and you should install the film by following these instructions:
- Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top.
- Observing where the HUD reflects, place the reflective film in position.
- Ensure the surface is clean and dry before installing the film.
- Remove the back protective side marked (1) and attach the film to the clean windscreen.
- Once you're satisfied with the location, use a credit card or similar to remove any bubbles or air pockets that remain.
- Remove the front side marked (2). If you need to adjust the HUD's reflection, reposition using the non-slip mat.
3. Operating Instructions
3.1. HUD Main Features
- Plug and Play connectivity with any OBDII or EUOBD capable vehicle.
- 5.5-inch, 5-colour display.
- Multi-colour design makes the screen easier to read, highlighting important details for quick viewing.
- Nanotechnology to eliminate unwanted reflections, making information easier to read.
- Displays driving mileage and consumption.
- Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, and ability to change units (e.g., Kilometre/mile).
- Auto power on and off with the vehicle.
- Automatic and manual brightness adjustment mode.

3.2. Unit Functions and Display Information


Unit Controls:
- OBDII cable input
- Power button
- Three-way wave button:
- Up button = up motion
- OK button = inward button press
- Down button = down motion
Display Information:
- Light sensor: Changes the unit's display brightness to suit the constantly changing environment whilst driving.
- Rotational speed: Indicates the rotational speed of the engine.
- Alarm icon panel: From left to right: Shift reminder, over speed alarm, engine fault, fatigued driver reminder, buzzer.
- Speed: Live speed.
- Rotational speed units: Indicating the units of rotational speed.
- Unit mark: KM/H = Kilometres/hour, MPH = Miles/hour, RPM = rotations per minute.
- Engine temperature: Live engine temperature.
- Secondary Alarm icon panel: From left to right: Engine temperature alarm, battery voltage alarm, overspeed alarm.
- Unit mark: Left to right top to bottom: Degrees (Celsius or Fahrenheit), KM = Kilometres, V = Voltage, M = Miles.
- Multifunction display window: Voltage, Mileage, Water temperature.
- Fuel consumption unit mark: L/100km = Litres/100 kilometres, L/H = Litre/hour.
- Fuel consumption display: Fuel consumption with adjustable units of measurement.
- Fuel consumption logo.

3.3. Setting Menu
A vehicle's instrument cluster has an offset value, meaning the value displayed on the factory instrument cluster is slightly higher than that computed by the vehicle. This offset value is different for different vehicle manufacturers. The HUD has a built-in offset from a large range of test data. If you find the value on your dashboard is different from the value displayed by the HUD, you can change it through the following procedure:
- Enter the setting mode by holding the wave button down for 5 seconds.
- Wave button functions:
- Press inwards = OK button
- Scroll down = down button
- Scroll up = up button
- Once in the setting mode, press the OK button to advance through the screens, and use the scroll buttons to adjust the parameters. The screen number you're in is displayed in the top right-hand corner.
- Once finished, exit the setting menu by holding down the wave button again for 5 seconds.
To switch display information: Vertically press the 'OK' button. You can switch the display information between: water temperature, battery voltage, mileage, default power. After a successful scan, you can display mileage.
To clear the fault code: When the HUD is connected to the car, please do not start the engine. Turn your car on but do not start the engine. Have the HUD turned off. Press the downside key for 5 seconds and you will hear a 'tick' sound, which means that the HUD is back to factory settings.
3.4. Function Display Video
Video 3.1: Demonstration of the HUD's display effects in various lighting conditions: day, exposure to sun, tunnel, and night driving.
4. Maintenance
To ensure optimal performance and longevity of your Liislee X6 HUD, keep the device and your windshield clean. Use a soft, dry cloth to wipe the HUD unit. For the reflective film on the windshield, use a glass cleaner that is safe for automotive use and a microfiber cloth to avoid scratches. Avoid exposing the device to extreme temperatures or direct sunlight for prolonged periods when not in use.
5. Troubleshooting
Some common problems are displayed below. If you incur any of these problems, please see the table for a solution.
| Problem | Possible Reason | The Way to Solve |
|---|---|---|
| No speed display | The setting value is too high or the function is closed | Cancel stages of alarm and open the switch of alarm |
| No rotating speed display | The setting value is too high or the function is closed | Reset the unit and open the switch of alarm |
| No display after starting | The switch is not opened | Open the switch and check the plug |
| Inaccurate display of fuel consumption | No air flow sensor | Reset the emissions and then calibrate |
| No speed or engine speed display | Not compatible with OBDII or EU-OBD port | Contact your vehicle manufacturer |
| No mileage display | No Settings for fuel and fuel consumption calibration | Switch to manual to input fuel and adjust fuel consumption |
| Speed is inaccurate | The unit of speed is MPH | Switch the unit of speed to KM/H |
| Display only shows speed and fuel | Speed exceeds 80KM/H | Enter into settings and switch display mode to 1 |
6. Specifications
6.1. Technical Parameters
- Environment temperature: -40 °C to +80 °C
- Barometric pressure: 86-106KPa
- Relative humidity: 10%-95%
- Environment voice: <=60dB
- Alarm sound level: >=30dB(A)
- Work voltage: 9V~16Vdc (12Vdc/400mA)
- Size of product: 12.5 x 7.5 x 1.5 cm
- Weight of product: 110g
- Speed type: OBD vehicle speed, GPS speed
- Output Frequency: Head Up Display
- Rated Power: 12V
- Size Name: 3 inch
- Wire or Wireless: Wire OBDII or EUOBD Connector
- Origin: Mainland China
- Fit Car: For BMW X3 X5 E36 E39 E46 E60 E90 F10 F20 F30
7. User Tips
- For best visibility, ensure the reflective film is applied smoothly without air bubbles.
- Adjust the brightness manually in very specific lighting conditions if the automatic adjustment doesn't meet your preference.
- Familiarize yourself with the wave button controls for quick access to settings and display changes while driving.
8. Warranty and Support
For any issues or support inquiries, please contact your nearest reseller or the point of purchase. Keep your proof of purchase for warranty claims. Specific warranty terms may vary by region and retailer.