IRALAN 5203

Contents

IRALAN Ceiling Fan with LED Light User Manual

Model: 5203 | Brand: IRALAN

1. Safety Information

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN.

  • To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
  • All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
  • The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet boxes marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less".
  • The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance from the trailing edge of the blades to the floor.
  • Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
  • Do not place objects in the path of the blades.
  • To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
  • Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
  • After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
  • All setscrews must be checked and re-tightened where necessary before installation.

WARNINGS:

  • Personal Injury: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
  • Fire or Electric Shock: This fan is NOT suitable for use with solid-state speed controls.
  • Electrical Shock: To avoid possible electrical shock, make sure that the electricity is turned off at the main power box before starting work. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
  • Electrical Diagrams: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
  • Mounting: To reduce the risk of fire, electrical shock or personal injury, ensure that the fan mounting bracket is supported directly from the building structure or the outlet box marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less". Use only the screws provided with the outlet box.

2. Warranty Information

To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions, this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of "wobble" is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hereby disclaims any and all warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

For a detailed user manual in PDF format, please refer to the User Manual (PDF).

3. Setup and Installation

3.1. Tools Required

  • Phillips screwdriver
  • Flat blade screwdriver
  • Step ladder
  • Drill
  • Wrench
Tools required for installation: Phillips screwdriver, flat blade screwdriver, step ladder, drill, wrench.

Image: Essential tools for assembling the ceiling fan.

3.2. Package Contents

Before beginning installation, ensure all parts are present and accounted for. The package includes:

ItemDescriptionQuantity
AABlade attachment screw and fiber washer6
BBTapping Screws4
CCExpansion Bolts2
KRemote control (Transmitter)1
LRemote control (Receiver)1
AFan-motor assembly1
BLED light kit1
CLamp panel1
DAcrylic sheet1
EInside canopy5
FBlade3
H10 CM Ball/downrod assembly1
GCanopy1
I20 CM Ball/downrod assembly1
JCoupling cover1

3.3. Mounting Hanger

Ensure the electrical mains are switched off at the circuit breaker fuse box before proceeding.

3.3.1. Wooden Ceiling Installation

  1. Use the Mounting Bracket (A) as a guide to mark the spots where the 4 Self Tapping Screws (B) will be drilled.
  2. Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, and install the mounting bracket onto the wooden ceiling with the 4 Self Tapping Screws (B).

IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG.

3.3.2. Concrete Ceiling Installation

  1. Use the Mounting Bracket (A) as a guide to mark the spots where the 2 Expansion Bolts (B) will be drilled.
  2. Remove the Mounting Bracket (A). Drill 2 holes for 8MM diameter and insert 2 Expansion Bolts (B) into the concrete ceiling. Install the mounting bracket and secure with Flat Washers (C), Spring Washers (D), and Nuts (E).

IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG.

3.4. Downrod Assembly

  1. Insert the canopy and the Bolt & Pin cover onto the downrod. Carefully feed motor wires through the downrod assembly.
  2. Slide the ball down the downrod.
  3. Put the round latch in.
  4. Replace the hanger ball at its normal position.
  5. Secure the two screws.

3.5. Hanging the Fan

  1. Thread the suspender through the suspended clock and coupling cover.
  2. Then insert the tail of the suspender from the lifting head of the motor.
  3. Remove the lateral pin out from the suspended head position, secure with R type pin (Clevis pin).
  4. Tighten the lifting head screws. Tighten the 2 Set Screws on the Coupling to serve as a clamping force on the Downrod to prevent fan shaking during operation.
  5. Route the Coupling cover, Canopy Ring, Canopy and Hanger Ball through the Downrod in turn, and then install the Lock pin through the hole on the Downrod. Fix it by Screw, then slip down the Coupling Cover in correct position.

3.6. Remote Control Receiver Installation

Once wiring is complete, slide the wired remote receiver in between the mounting bracket and the top of the downrod ball for downrod fans.

3.7. Canopy Installation

  1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
  2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.

3.8. Attaching the Fan Blades

CAUTION: To reduce the risk of electric shock, disconnect the electrical circuit to the fan before installing the light fixture.

  1. Remove 6 screws from the motor.
  2. Attach the blades to the motor using the removed screws.

3.9. Attaching the Light

  1. Remove three screws from the plate on the motor.
  2. Use these three screws to assemble the light kit fitter.
  3. Connect the light source and lock it to the lamp tray with three screws.
  4. Install the acrylic sheet.

4. Operating Instructions

4.1. Remote Control Operation

The remote control must match the same code as the receiver.

ButtonFunction
1NO/OFF (Fan and Light)
2Wind speed 1-6 gear
3Increased brightness
4Reduced brightness
5Fan forward/reverse switch
6General (turn off all functions)
7Turn off the fanCode
8Increased color temperature
9Lower color temperature
10Natural Wind mode
112-hour timer
12Night light mode
Image of the remote control in use, showing buttons for fan speed, light brightness, color temperature, reverse function, and timers.

Image: Remote control layout and functions.

Image showing the fan's dimmable LED light with three color options: Warm, Natural, and White, and a brightness slider.

Image: Dimmable LED light with adjustable color temperature (Warm, Natural, White) and brightness (0-100%).

Image showing the fan's reversible function for summer mode (downward airflow) and winter mode (upward airflow).

Image: Reversible function for Summer (cooling) and Winter (air circulation) modes.

4.2. APP Control Instruction

  1. Step 1: Scan the QR Code to download and install the app on your phone.
  2. Step 2: Turn on the light and search for the fan in the app, then pair them.
  3. The buttons 1-6 control the power of the fan.
  4. To change the color temperature, use the corresponding controls in the app.
  5. To pair, turn on the light and immediately press the pairing button in the app.
  6. The app allows control of lamp on/off, fan on/off, and power switch.
Screenshot of the mobile app interface for controlling the fan and light, showing fan speed, timing settings, reverse function, dimming, night light, and natural wind modes. Includes a QR code for app download.

Image: Smart APP interface for fan and light control, including QR code for download.

4.3. Remote Control Wiring Diagram

WARNING: Turn off the electric power during installation and making wire connection.

  1. Connect the wire from the ceiling fan into the receiver.
  2. Connect the wire from the receiver with the wire from the house.

Note: A detailed wiring diagram is typically provided in the PDF manual for visual reference.

5. Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

  • Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
  • Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
  • You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
  • You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

6. Troubleshooting

ProblemSolution
The fan will not start
  • Check the main and branch circuit fuses or breakers.
  • Check the line wire connections to the fan and switch wire connections in the switch housing.
The fan is noisy
  • Ensure all motor housing screws are snug.
  • Ensure the screws that attach the fan blade bracket to the motor hub are tight.
  • Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
  • Allow a 24-hour "breaking in" period. Most noises associated with a new fan disappear during this time.
  • If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
  • Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
  • Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

7. Specifications

FeatureDetail
Brand NameIRALAN
Model Number5203
Item TypeCeiling Fans
StyleModern Style
Installation MethodAssembly
Power SourceAC
Control MethodREMOTE CONTROL, APP Control (Bluetooth)
Switch TypeREMOTE CONTROL
Number of Blades3
Body MaterialABS, IRON
Light SourceIntegrated LED Light Source
Is DimmableYes (Brightness 0-100%, 3 Color Temperatures)
Luminous Flux2000-82000 Lumens
Base TypeWedge
FinishNone
Number of Lights>8 (LEDs)
CertificationCCC, CE
Warranty1 year
OriginMainland China
Hign-concerned ChemicalNone
FeaturesLong Blade Fan Light with Rod, Reversible Function, 6 Fan Speeds, Timing Setting, Smooth Dimming (5%-100%), Night Light, Natural Wind, Brushless DC Motor

7.1. Dimensions and Electrical Parameters

Diagram showing dimensions of the ceiling fan: 5.9 inch (15cm) canopy diameter, 2.2 inch (5.8cm) canopy height, 6.7 inch (17cm) fan body height, and available downrod lengths of 10cm and 20cm. Fan sizes are 52 inch (132cm) and 42 inch (105cm). Electrical parameters include Input Voltage: 85-265V, Motor Power: 30W, LED Power: 18W, Application Space: 10-20M², Wind Speed: 6 Gears.

Image: Detailed dimensions and electrical specifications.

ParameterValue
Input Voltage85-265V
Motor Power30W
LED Power18W
Application Space10-20M²
Wind Speed6 Gears
Fan Size Options42 inch (105cm), 52 inch (132cm)
Downrod Lengths10cm, 20cm
Detailed view of the brushless DC motor, highlighting its frictionless performance and 6-speed capability.

Image: Brushless DC Motor details.

8. User Tips

  • The fan operates quietly and provides effective lighting.
  • The device comes with two downrod lengths (10cm and 20cm); choose the appropriate one for your ceiling height and room dimensions.
  • The white color option of the fan is noted to blend easily with most ceiling aesthetics.
  • Many users find the fan to be a strong and effective alternative to air conditioning, especially during warmer temperatures.

9. Frequently Asked Questions (FAQ)

Q: Can you choose the color of the light?
A: Yes, the LED light is dimmable and allows selection from three color temperatures: Warm, Natural, and White. Brightness is also adjustable from 0-100%.

© 2023 IRALAN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.