1. Introduction
Thank you for choosing the Aurora Tattoo Power Supply. This professional power supply is designed for both coil and rotary tattoo machines, offering stable and precise voltage control. This manual provides essential information for the safe and efficient operation of your device.

Figure 1: Aurora Tattoo Power Supply with its retail packaging.
2. Package Contents
Please check the box for the following items:
- 1 x Aurora Tattoo Power Supply (Model FTP-003)
- 1 x Power Adaptor (EU/USA/UK plug type as selected)
3. Product Overview
The Aurora Tattoo Power Supply features a user-friendly design with intuitive controls and clear indicators.

Figure 2: Front view of the power supply with labeled components.
Component Identification:
- LED Voltage Display Window: Shows the current output voltage.
- Voltage Adjust UP Button: Increases the output voltage.
- Left Button: Used in 2-machine running mode.
- Tattoo Machine Input: Connect your tattoo machine here.
- Power Input: Connect the power adaptor here.
- Footswitch Mode Button: Toggles between momentary and maintained footswitch modes.
- Voltage Adjust DOWN Button: Decreases the output voltage.
- Right Button: Used in 2-machine running mode.
- Food Pedal or 2nd Tattoo Machine Input: Connect your footswitch or a second tattoo machine here.

Figure 3: Connection interface details.
Key Features:
- LED voltage display with 5 easy touch setup buttons.
- Backlight that flashes to indicate the voltage in use.
- Compatible with all coil and rotary tattoo machines.
- Two footswitch modes: maintained or momentary.
- Jump-start mode feature for rotary tattoo machines.
- Built-in magnets and silicone grips on the non-slip base for secure placement.

Figure 4: Non-slip base with built-in magnets for stability.
4. Setup Instructions
- Place the Power Supply: Position the Aurora Tattoo Power Supply on a stable, clean surface. The non-slip base and built-in magnets will help secure it.
- Connect Power: Plug the provided power adaptor into the Power Input (5) on the back of the unit, then plug the adaptor into a suitable wall outlet (110-240V).
- Connect Tattoo Machine: Plug your tattoo machine's clip cord into the Tattoo Machine Input (4).
- Connect Footswitch (Optional): If using a footswitch, plug it into the Food Pedal or 2nd Tattoo Machine Input (9). The unit can operate without a footswitch.
5. Operating Instructions
5.1 Powering On/Off
The unit powers on automatically when connected to power. To turn on/off the output, use the rotary control push knob (top dial).
5.2 Adjusting Voltage
Use the Voltage Adjust UP Button (2) and Voltage Adjust DOWN Button (7) to set your desired output voltage. Each press adjusts the voltage by 0.1V. The voltage range is from 1.5V to 16V.
5.3 Voltage Indicator Colors
The backlight of the power supply changes color to indicate the current voltage range:
- Blue: 1.5V - 3V
- Light Blue: 3V - 5V
- Green: 5V - 7V
- Purple: 7V - 11V
- Yellow: 11V - 14V
- Red: 14V - 17V

Figure 5: Voltage indicator light values.
5.4 Footswitch Modes
Press the Footswitch Mode Button (6) to toggle between:
- Momentary Mode: Power is supplied only while the footswitch is pressed.
- Maintained Mode: Press the footswitch once to turn on power, press again to turn off.
5.5 Jump-Start Mode
This feature is designed for rotary tattoo machines that require a higher initial voltage to start. The power supply automatically provides a brief surge to ensure smooth startup.
5.6 Two Machine Running Mode
The Aurora Tattoo Power Supply supports running two tattoo machines simultaneously.
Setup for 1 Tattoo Machine:
Hold the Voltage Adjust UP Button (2) and Left Button (3) for 3 seconds. The LED display will show