XTOOL D7S

Contents
XTOOL D7S Smart Diagnostic System

XTOOL D7S Smart Diagnostic System User Manual

Version 1.4 | 2025.09

1. General Introduction

The XTOOL D7S smart diagnostic system, referred to as the "Scan Tool" throughout this document, is an advanced scanning tool based on the Android operating system. It supports multiple languages and is suitable for different countries and regions. This OBD-II (On-Board Diagnostics version 2) scanner offers comprehensive functions and the ability to quickly provide accurate diagnostic information.

Please read this user manual carefully before using the Smart Diagnostic System. Pay attention to the words "Note" or "Caution" for appropriate operation.

Tablet Overview

The XTOOL D7S tablet features a robust quad-core processor, 64GB memory, a 7-inch 1024x600 resolution touch screen, a 2500mAh 7.3V built-in battery, microphone, dual speakers, and an intuitive interface for maximum efficiency in auto repair and maintenance.

XTOOL D7S Hardware Configuration

Image: XTOOL D7S Hardware Configuration showing key specifications.

XTOOL D7S Tablet Diagram

Image: Diagram of the XTOOL D7S tablet highlighting its components.

Tablet Components:

  1. USB Port
  2. DB15 Port
  3. Reset Hole
  4. Power Button
  5. Microphone
  6. Camera
  7. Nameplate
  8. Speaker
  9. Tablet Holder

2. Safety Information and Cautions

Operation Instructions for Safety

  • Keep the device away from heat or fumes when in use.
  • If the vehicle battery contains acid, keep your hands and skin or fire sources away from the battery during testing.
  • Ensure adequate ventilation as vehicle exhaust gas contains harmful chemicals.
  • Do not touch vehicle cooling system components or exhaust manifolds when the engine is running due to high temperatures.
  • Make sure the car is securely parked, and Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
  • Ensure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
  • Do not switch off the power or unplug the connectors during testing, as this may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.

General Cautions

  • Avoid shaking, dropping, or dismantling the scan tool as it may damage internal components.
  • Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the scan tool.
  • Do not use excessive force.
  • Do not expose the screen to strong sunlight for a long period.
  • Keep the scan tool away from water and moisture.
  • Store and use the scan tool only within the temperature ranges identified in the Technical Specifications section.
  • Keep the unit away from strong magnetic fields.

3. Setup

3.1 Vehicle Connection (Wired)

To connect the XTOOL D7S to your vehicle, follow these steps:

  1. Press and hold the Power button to turn on the tablet.
  2. Select the App language and start the activation. Follow the hints to complete the activation.
  3. Connect the main cable to the tablet and tighten the screws.
  4. Plug the DB15 main cable into the vehicle's DLC port via the OBD2-16 adapter.
  5. Your tablet is now ready for diagnosis.

*For models with DoIP protocol communication, ensure the device is connected to the vehicle by wire.

Step 1: Power on tablet and activate
Step 1: Power on tablet and activate.
Step 2: Connect main cable to tablet
Step 2: Connect main cable to tablet.
Step 3: Plug DB15 cable into vehicle's DLC port
Step 3: Plug DB15 cable into vehicle's DLC port.
Step 4: Tablet ready for diagnosis
Step 4: Tablet ready for diagnosis.

3.2 Language Settings

The XTOOL D7S supports 22 languages including English, French, German, Russian, Spanish, Polish, Italian, Portuguese, Dutch, Danish, Japanese, Finnish, Arabic, Korean, Vietnamese, Thai, Norwegian, Turkish, Hungarian, Greek, Swedish, and Traditional Chinese. English is the default language.

Steps to Set the Language:

  1. Activate the device with your email address and serial number.
  2. Contact the seller to authorize the desired language.
  3. Switch the language in the device settings (Diagnosis App->Setting->Language).
  4. Click 'Update Device' to download the necessary language packages.

Note: If you cannot switch languages at will, please update the APP to the latest version (Diagnosis App->Setting->App).

Language Selection Screen

Image: Screen showing language selection options.

4. Operating Instructions

4.1 Precautions for Diagnosis

  • The voltage range on the car should be +9V to +36V DC.
  • When testing special functions, operate according to prompts and meet test conditions (e.g., engine water temperature 80°C-105°C, headlights/AC off, accelerator pedal released).
  • If the vehicle type or electronic control system is not found, upgrade the diagnostic software or consult XTOOL technical service.
  • Only use wiring harnesses provided by XTOOL to avoid damage.
  • Do not shut down the device directly when running a Diagnostics function; cancel the task before returning to the main interface.

4.2 Vehicle Selection

The scan tool supports three methods to access the smart diagnostics system:

  • AUTO SCAN: Automatically reads the vehicle VIN code. Ensure the car and device are well connected.
  • MANUAL INPUT: Allows manual entry of the 17-character VIN code for accurate test results.
  • SELECT VEHICLE BY AREA: Choose a car brand by selecting the appropriate region (e.g., Europe, America, Asia) and then the specific vehicle model.

If your model is not recognized, please try the following steps:

  1. Update all software and check if the APP is updated in [Settings].
  2. Click Diagnosis on the main menu, manually select the engine system to read the ECU information, and confirm if the VIN can be read.
  3. Contact the XTOOL technical team with the VIN code to confirm model support for automatic VIN identification.
Vehicle Selection by Area
Vehicle Selection by Area showing various car brands.
Manual VIN Input Keyboard
Manual VIN Input Keyboard for entering vehicle identification numbers.

4.3 Diagnosis Functions

The diagnostic application can read ECU information, read and clear DTC (Diagnostic Trouble Codes), and check live data and freeze frame data. It accesses ECUs of various vehicle control systems (Engine, Transmission, ABS, SRS, EPB) and performs actuation tests.

  • Read ECU Information
  • Read/Clear Trouble Code
  • Read Live Data
  • Freeze Frame
  • Actuation Test (Bi-Directional Control)
  • Special functions

4.3.1 Read ECU Information

This function reads ECU version information, including software/hardware versions, models, production date, and part numbers. This is useful for maintenance records and ordering parts.

Read ECU Information Screen

Image: Screen displaying ECU information such as system name, programming date, and series number.

4.3.2 Read and Clear Trouble Codes (DTCs)

The diagnostic application can read current, pending, and history DTCs. If "System is OK" or "No Trouble Code" is displayed, it means no related trouble code is stored or troubles are not ECU-controlled. Most troubles are mechanical or executive circuit issues, or inaccurate sensor signals, which can be examined using Live Data.

To clear trouble codes, select the "Clear Trouble Code" function. This will erase current and historical DTCs from the ECU memory, assuming all issues have been resolved.

DTCs Report Screen

Image: Screen showing a DTCs Report with trouble codes and descriptions.

4.3.3 Read Live Data

Live Data provides real-time information from various sensors, including PIDs (Parameter Identifications) like oil pressure, temperatures, engine speed, etc. This helps predict problem locations and narrow down maintenance scope. Some vehicles may not support all live data items.

8-in-1 Live Data Graphing

Image: Comparison of XTOOL's 8-in-1 live data graphing versus others' 4-in-1.

Customizing Live Data Display:
  • Search PIDs: Click the magnifying glass icon to search for PIDs by keywords.
  • Custom Display: Select multiple PIDs and click "Display All" to show them.
  • Combine Graphs: Select multiple PIDs and click "Combine" to display different graphs into one chart.
Data Recording:

The scan tool supports recording current data values as text. Recorded files can be viewed in Reports->Data Replay. You can pause the recording timeline using the dedicated button.

4.3.4 Freeze Frame

When a sensor signal is abnormal, the ECU saves data at that moment as a freeze-frame, used to analyze component failures. The availability of freeze-frame data varies by vehicle model.

If a fault code (e.g., DF1068) is listed, clicking it will show the freeze frame, including the context when the fault appeared, current context, and additional data.

Freeze Frame Data Screen

Image: Screen showing freeze frame data with fault context and additional data.

4.3.5 Actuation Test (Bi-Directional Control)

This function allows sending commands to the vehicle ECU to perform active tests on various parts and subsystems, checking their working status. This interactive approach helps identify and resolve issues efficiently.

  • EVAP Tests
  • Compression Test
  • Turn On/Off Radiator Fan
  • A/C Clutch On/Off
  • Fuel Pump
  • Window/Mirror/Door Lock Test
  • Pump and Value Tests
  • Interior & Exterior Lights Test
  • Sound Horn Test

Note: Available active tests vary by vehicle system. Please send the specific car model to the seller to check compatibility before purchasing.

Video: Demonstration of XTOOL D7S bi-directional control capabilities, showing various actuation tests.

4.3.6 Special Functions (39+ Common Resets)

Special functions provide various reset or re-learning menus for most vehicle systems, helping to quickly resolve faults. After some functions are executed, fault codes may be generated and need to be cleared manually.

39+ Hot Reset Service

Image: Overview of 39+ hot reset services available on the XTOOL D7S.

Note: Service Functions Vary By Vehicle Model, Not Universal. Please consult us for vehicle compatibility Before purchasing.

ABS Bleeding

This function bleeds the brake system to restore ABS brake sensitivity when air is present. It's performed when replacing brake distributor pumps, severe fluid shortage, or changing brake fluid.

Operation Guidelines:
  1. Read operating instructions and precautions on screen.
  2. Attach bleeder bottle to the left rear bleeder screw.
  3. Open the left rear bleeder screw.
  4. Click "OK" to start bleeding, pumping the brake pedal continuously every 2 seconds.
  5. Continue pumping until air bubbles are gone, then click "OK" for the next wheel.
  6. Repeat for left front, right front, and right rear wheels.
  7. Stop pumping and close the right rear bleeder screw.
  8. Click "OK" to complete.

Caution: The ABS pump screw needs to be unscrewed. Brake fluid will be under pressure; secure the bleed hose and open bleeder screws slowly. Some vehicles may require manual bleeding.

Oil Reset

Resets the engine oil life system after an oil change, allowing the system to calculate the next service interval. This is necessary if the service lamp is on or after changing oil/oil-monitoring electrical appliances.

Operation Guidelines:
  1. Enter the Oil Reset menu and select your vehicle model.
  2. Follow on-screen instructions and press OK.
  3. Enter the Maintenance mileage reset menu.
  4. Click INPUT, enter a reasonable remaining oil life value, and press OK.
  5. Confirm the new value and press OK.
EPB Reset

Resets the electronic parking brake system and brake pads (retraction, release of brake pump), G-sensor, and body angle calibration. Necessary when brake pads wear, indicator lamp is on, sensor circuit is shorted, or servo motor is replaced.

Operation Guidelines:
  1. Enter the EPB menu and select your vehicle model.
  2. Follow on-screen instructions and press YES.
  3. Enter the "Enter maintenance mode" menu, release the handbrake, and press OK.
  4. Wait for "Successful operation" message and press OK.
  5. Enter "Exit maintenance mode" and wait for "Successful operation".
SAS Adjustment (Steering Angle Sensor Calibration)

Permanently stores the current steering wheel position as the straight-ahead position. Front wheels and steering wheel must be straight before calibration. Necessary after replacing steering angle position sensor, steering mechanical parts, four-wheel alignment, or car body repair.

Operation Guidelines:
  1. Enter the SAS menu and select your vehicle model.
  2. Enter the "Set steering angle sensor" menu and follow instructions.
  3. Wait for instructions to display and press YES.
  4. Follow instructions and press OK.
  5. Wait for instructions to display and press OK.
  6. "Function execution is completed" message indicates success.
BMS Reset (Battery Management System)

Evaluates battery charge state, monitors current, registers battery replacement, and activates rest state. Clears low battery fault information and performs battery matching after replacement.

Operation Guidelines:
  1. Enter the BMS Reset menu and select your vehicle model.
  2. Turn on the ignition switch.
  3. Press OK to continue.
  4. Enter battery capacity (0-255 Ah) and press OK.
  5. Enter battery manufacturer and press OK.
  6. Enter the 10-digit battery serial number and press OK.
Injector Coding

Writes the identification code of the fuel injector into the ECU, allowing the ECU to recognize new injectors. Necessary after replacing the ECU or injector to ensure accurate fuel injection control.

Note: Generally, coding is not needed after cleaning. Injector identification includes working accuracy and type value. When replacing, find the corresponding model. Most mainstream cars support this function.

Operation Guidelines:
  1. Enter the Injector coding menu and select your vehicle chassis model.
  2. Enter the "Fuel injection nozzle injection volume adjustment" menu.
  3. Read the note carefully and press OK.
  4. Read and confirm values stored in cylinders.
  5. Enter the "Change the value of cylinder" menu, input the new 5-digit value, and press OK.
  6. Wait for "Write successfully" message.
  7. Turn off ignition switch.
  8. Wait for prompt to turn on ignition switch.
  9. Re-enter "Fuel injection nozzle injection volume adjustment" to verify new values.
DPF Regeneration (Diesel Particle Filter)

Manages DPF regeneration, component replacement teach-in, and teach-in after ECM replacement. Clears PM (Particulate Matter) from the DPF filter. Necessary when exhaust back pressure sensor, PM trap, fuel additive nozzle, or catalytic oxidizer is replaced, DPF regeneration MIL is on, or DPF regeneration control module is replaced.

Operation Guidelines:
  1. Enter the DPF menu and select your vehicle model.
  2. Enter the DPF regeneration menu.
  3. Read prerequisites carefully and press OK.
  4. Read fuel tank level and carbon deposit load.
  5. Choose "drive to warm up" and follow instructions, then press OK.
  6. Read instructions and press OK.
  7. Follow instructions and press OK to start regeneration.
  8. Wait for carbon deposit value to decrease and "Emergency regeneration has been completed" message (up to 40 minutes).
  9. Wait 2 minutes for particulate filter to cool down.
  10. Press "drop out" to exit.
TPMS Reset (Tire Pressure Monitoring System)

Performs learning, matching, and resetting functions for tire pressure sensors. Necessary for tire replacement, troubleshooting tire pressure problems, or other signal loss issues.

Note: Some models may require a TPMS activation tool. After learning, the car may need to be driven for a while for the fault light to go off. Tire pressure imbalance can also cause the light.

The function offers 6 menus for major automotive manufacturing regions: Korea, Japan, USA, China, Australia, and Europe.

Methods:
  • Automatic Relearn: Install/adjust sensors, keep vehicle still for 20+ mins, drive 30-100km/h for 15+ mins.
  • Static Relearn: Install/adjust sensors, pull parking brake, ignition ON/RUN (engine off), enter learning mode, activate sensors with TPMS Activation Tool.
  • OBD Relearn: Requires TPMS Activation Tool. Install/adjust sensors, activate all sensors, connect tool to OBD port, perform relearn, ignition ON/RUN, re-trigger sensors, power off for 25+ mins, drive 30-100km/h for 15+ mins.
  • Copy ID Relearn: Copies original sensor ID to new sensor using TPMS Activation Tool.

Note: This Scan Tool provides TPMS Reset/Relearn functions but not activation of TPMS sensors. For activation, consult a professional TPMS activation tool.

Key Programming

The XTOOL D7S performs key programming functions, including:

  • Read Pincode
  • Generate key, Key Refresh
  • Make Dealer Key
  • All Key Lost
  • Immobilizer Data Reading & Writing
  • Backup IMMO Data
  • Remote Frequency Detection
  • Immobilizer Module Replacement
  • IMMO ECU Reset & Coding
Key Programming Interface

Image: Screen showing key programming options like adding/deleting keys and handling all keys lost scenarios.

ECU Offline & Online Coding

The D7S features advanced ECU coding to reprogram adaptive data, enhance vehicle performance, and customize car settings. It supports:

  • ECU Online Coding (for BMW, Mercedes-Benz, VW)
  • ECU Offline Coding (for VW, Audi, Skoda, Benz, Mitsubishi)
  • Recoding Changed Modules
  • Optimizing Vehicle Performance
  • Refreshing Hidden Features
  • Renewing ECUs Coordination
  • Reinforcing Performance

Note: ECU Coding is not suitable for all vehicles. Please check compatibility with VIN before purchasing.

ECU Coding Interface

Image: Diagram illustrating ECU coding capabilities, including customizing OE settings, flashing hidden functions, and disabling unwanted functions.

VAG Guided Functions

Provides step-by-step guidance for VAG group cars (VW/Audi/Skoda) to diagnose vehicle faults, helping users quickly and accurately locate problems.

VAG Guided Functions

Image: Screen showing VAG Guided Functions for step-by-step troubleshooting.

FCA AutoAuth

Features FCA AutoAuth capability, allowing diagnostics for Chrysler, Jeep, Dodge, and Fiat from 2018 onwards without a bypass cable. This enables clearing codes, running bi-directional active tests, and performing special functions.

Note: An FCA account is needed before applying on the scanner.

FCA AutoAuth and CAN FD & DoIP Protocol

Image: Diagram explaining CAN FD and DoIP protocol support, including FCA AutoAuth for Chrysler, Dodge, Jeep, and Fiat.

CAN FD & DoIP Protocol Support

Built-in CAN FD protocol supports the latest GM vehicles manufactured after 2020, offering high-speed communication for in-vehicle control and real-time data transfer.

Built-in DoIP protocol is compatible with F&G chassis BMW, Land Rover, and Jaguar models, providing fast, detailed diagnostic information over IP networks.

5. Maintenance

5.1 Software Update

After activating the device, update the software modules via the "Updates" screen. The device identifies all available software packages for download directly via the Internet.

Caution: If you change the language configuration after contacting XTOOL Support, you need to download all software packages again.

3 Year Free Update

Image: Graphic indicating 3 years of free software updates for the XTOOL D7S.

5.2 Factory Reset

Restoring factory settings in the Android OS system erases custom settings and data, restarts the device, and enters factory reset mode. This is initiated from the main home page by clicking "Settings" then "Backup & reset".

Factory Reset Language Selection

Image: Screen showing language selection and Wi-Fi connection options after a factory reset.

5.3 Diagnostic Report

The Diagnostic Report feature is used for viewing and printing saved files, including Live Data, Trouble codes, or pictures generated during diagnosis. It provides a history of diagnostic reports that can be viewed and deleted. A prompt for report regeneration appears after finishing diagnostics for a specific vehicle.

Printing a Diagnostic Report:

  1. Install a printer APP on the tablet and add your printer (or contact XTOOL support).
  2. On the Android main menu, go to Settings -> Printing -> Turn printer on.
  3. In the Report section, choose the report, then "Print PDF Report" -> Print.
  4. Click the top-left corner of the screen, choose the added printer, and click print.

Note: The scan tool does not provide printer driver software; a third-party app is needed. Vehicle information in the report can be edited by clicking the pen icon.

Diagnostic Report V2.0

Image: Screen showing the Diagnostic Report V2.0 interface, emphasizing customization and sharing options.

6. Troubleshooting

6.1 DTC Status Descriptions

Understanding Diagnostic Trouble Code (DTC) statuses is crucial for effective troubleshooting:

DTC StatusDescriptionSuggestions
Current/PresentDTCs stored in the ECU when continuous and non-continuous (2 trip) monitors fail. They command the MIL (Malfunction Indicator Lamp) on instantly.Can be cleared using the Scan Tool's Clear DTC function, or when the ECU monitor completes 40 consecutive trips without a fault.
History/StoredDTCs stored when continuous and non-continuous monitors (2nd trip) fail. Set in conjunction with Current DTCs and not cleared by the ECU monitor.Can only be cleared using the Clear DTC function of the Scan Tool.
PendingCodes that prepare themselves when they determine a fault in an engine cycle. A preliminary investigation for your engine. A random malfunction can occur during the current drive cycle but only happen for a split second. This causes a "pending code".Typically not severe but shouldn't be ignored. Can be cleared using the Clear DTC's function.
PermanentDTCs stored in the ECU when continuous and non-continuous monitors fail. Set in conjunction with Current and History DTCs.Cannot be cleared using the Clear DTC's function. Cleared when the ECU monitor completes and passes three consecutive trips.
Active/Static (For Volkswagen)Means the fault is happening at the moment and should be taken care of.Cannot be cleared directly by the Clear DTC's function. The internal fault must be eliminated manually.
Passive/SporadicA fault that has occurred in the past and can be cleared by Scan Tool. User should check if the DTC will appear again.N/A

6.2 General Troubleshooting Tips

  • Connectivity Issues: Ensure the OBD2 cable is securely connected to both the vehicle's DLC port and the XTOOL D7S. Check for any damage to the cable.
  • Device Not Powering On: Verify the device battery is charged. If using an external power source, ensure it's functioning correctly.
  • Software Freezes/Crashes: Restart the device. If the issue persists, perform a factory reset (see Maintenance section).
  • Inaccurate Readings/Functions Not Working:
    1. Ensure the vehicle's ignition is on (or engine running, as required by the function).
    2. Verify the correct vehicle model and year are selected in the diagnostic software.
    3. Update the diagnostic software to the latest version.
    4. Check for specific vehicle requirements for the function (e.g., engine temperature, parking brake engaged).
  • Compatibility Concerns: If a function is not supported for your vehicle, contact XTOOL technical support with your VIN, year, and model for compatibility verification.

7. Specifications

FeatureSpecification
Model NameXTOOL D7S
Operating SystemAndroid 10
ProcessorQuad Core 1.5Ghz
Memory2GB RAM, 64GB Flash
Screen Size7 inches (1024*600 resolution)
Operation ModeTablet Touch Screen
Connection MethodWire Connection
Battery Capacity2500mAh 7.3V
Update MethodWIFI online upgrade
Free Update Period3 Years
Charging MethodAdapter Charging
Supported ProtocolsCAN FD, DOIP, FCA, ISO 15765-4 (CAN-BUS), ISO 9141-2, ISO 14230-4, SAE J1850 PWM, SAE J1850 VPM
USB InterfaceUSB2.0
WIFI2.4G/5G
Item Weight2.5kg
Item Dimensions (L x W x H)37cm x 11cm x 29cm
MaterialPlastic
External Testing CertificationCE

7.1 Packing List

The XTOOL D7S package includes the following items:

  • 1PC X D7S Main Unit
  • 1PC X Quick Start Guide
  • 1PC X DB15 to OBD2-16 Main Cable
  • 1PC X Power Charger
  • 1PC X USB3.0 Data Cable
  • 1PC X Charger UE
  • 1PC X Charger US
  • 1PC X Charger UK
  • 1PC X Packing List
  • 1PC X Tool Kit
  • 1PC X Carton
XTOOL D7S Packing List

Image: Visual representation of the complete packing list for the XTOOL D7S, including various adapters and cables.

8. Warranty and Support

The XTOOL D7S comes with a 2-year warranty and 3 years of free software updates. Lifetime technical assistance is also provided.

8.1 Aftersales Services

For technical support or inquiries, please contact XTOOL via:

For remote assistance, tap on "Remote" to start the TeamViewer quick support program. Provide your device ID to XTOOL technical support for remote control.

TeamViewer QuickSupport Screen

Image: Screen showing the TeamViewer QuickSupport interface with device ID for remote assistance.

9. User Tips

  • Compatibility Check: Before purchasing or attempting specific functions, always verify compatibility with your vehicle's VIN, year, and model by contacting XTOOL support. Many advanced functions are not universally supported across all vehicles, despite general claims.
  • Software Updates: Regularly update the device software to ensure access to the latest models, functions, and bug fixes. This can resolve many diagnostic issues.
  • Language Authorization: If you need a language other than English, remember to contact the seller for authorization after activating the device.
  • Diagnostic Report: Utilize the diagnostic report feature to save and share detailed fault information, which can be helpful for further analysis or professional consultation.

10. Frequently Asked Questions (FAQ)

Q: Will this work on a 2011 Nissan X-Trail T31?
A: For specific vehicle compatibility, it is recommended to contact XTOOL support with your full VIN, year, and model to confirm. Functions vary by vehicle.
Q: Does it have cluster settings?
A: The XTOOL D7S supports various special functions, including "Instrument Cluster" related operations. However, specific capabilities like "cluster settings" can vary by vehicle model. Please check compatibility with your VIN.
Q: What vehicles can this be used with?
A: The XTOOL D7S works for 85+ car makers, 140+ brands, covering over 10,000+ cars, including 12V Petrol Sedans, SUVs, Minivans, and Light-Duty Trucks across Europe, America, Asia, Australia, and China. For a detailed list, refer to the "Work for 85+ Car Maker" section or contact support with your VIN.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.