diymore DC-DC Boost Converter Module

Contents

DC-DC Boost Converter Module Instruction Manual

Model: DC-DC Boost Converter Module

Brand: Diymore

1. Introduction

This manual provides detailed instructions for the Diymore DC-DC Boost Converter Module. This ultra-small and lightweight module is designed to efficiently boost low DC input voltages to stable 3V, 3.3V, or 5V DC outputs, making it ideal for various low-power electronic applications.

Key features include high efficiency, low quiescent current, and compact dimensions, ensuring reliable performance for your projects.

2. Specifications

General Specifications:

  • High Efficiency: 95% (typically 75% - 93%)
  • Low Quiescent Current: 13uA
  • Working Frequency: 350KHz
  • Ultra-small Size (excluding pins): 10.7 x 10.6 x 5.6 mm
  • Ultra-lightweight: 0.9g (with pins), 0.65g (without pins)

Output Voltage Variants:

Output Voltage Input Voltage Range Output Accuracy
3V DC 0.7V ~ 3V ± 2%
3.3V DC 0.8V ~ 3.3V ± 2%
5V DC 1V ~ 5V ± 2%

The module is available with or without pre-soldered pins, offering flexibility for different integration needs.

3. Setup and Connection

The DC-DC Boost Converter Module features clearly labeled input and output terminals for straightforward connection. Ensure correct polarity when connecting power sources and loads.

Pinout Description:

  • Vi: Voltage Input (Positive)
  • GND: Ground (Common for Input and Output)
  • Vo: Voltage Output (Positive)

Wiring Diagram:

Wiring diagram for the DC-DC Boost Converter Module, showing input Vcc, input GND, output Vcc, and output GND connections.
Figure 1: Wiring diagram for the DC-DC Boost Converter Module. Connect your input voltage to 'Vi' and 'GND', and draw your boosted output voltage from 'Vo' and 'GND'.

Module Variants:

The module is available in different output voltage versions (3V, 3.3V, 5V) and with or without pre-soldered pins. Below are visual examples of the modules:

3V output module with pins
3V Output Module (with pins)
3.3V output module with pins
3.3V Output Module (with pins)
5V output module with pins
5V Output Module (with pins)
3V output module without pins
3V Output Module (no pins)
3.3V output module without pins
3.3V Output Module (no pins)
5V output module without pins
5V Output Module (no pins)

4. Operating Instructions

Once correctly wired, the module will automatically boost the input DC voltage to the specified output voltage (3V, 3.3V, or 5V depending on the module variant). No additional configuration is typically required.

Important Considerations:

  • Input Voltage Range: The input voltage must not exceed the maximum specified input range for your module variant. Refer to the Specifications section.
  • Output Power: Do not exceed the maximum load capacity of the module for extended periods. Overloading can lead to damage or reduced performance.
  • Power Consumption: The input power supplied to the module must always be greater than the output power required by your load, accounting for the module's internal power consumption and efficiency losses.

5. Maintenance

The DC-DC Boost Converter Module is a low-maintenance electronic component. To ensure its longevity and optimal performance, please observe the following:

  • Keep Dry: Avoid exposure to moisture or liquids.
  • Temperature: Operate within typical room temperatures. Avoid extreme heat or cold.
  • Handle with Care: Electronic components are sensitive. Avoid physical shock or bending of pins.
  • Cleanliness: Keep the module free from dust and debris. Use a soft, dry brush if cleaning is necessary.

6. Troubleshooting

Problem: Output voltage is lower than the nominal voltage.

Solution: This often indicates that the input power is too low. Use a multimeter to test the input voltage. Ensure it is within the specified input range for your module and that your power source can supply sufficient current for both the module and your connected load.

7. User Tips

This versatile boost converter module is suitable for a wide range of applications, including:

  • Powering AA/AAA dry battery-powered equipment.
  • Providing power for breadboard circuits.
  • Driving small power motors.
  • Use in cameras and camcorders.
  • Integration into electric toys.
  • Powering model planes and other hobby electronics.

8. Warranty and Support

For any technical assistance, warranty claims, or further inquiries regarding your Diymore DC-DC Boost Converter Module, please contact the seller or manufacturer directly through your purchase platform. Please have your order details ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.