Introduction
This manual provides detailed instructions for the safe and proper installation and operation of your BEISHI BK-LB440 Adjustable Full-Motion TV Wall Mount. Please read this manual thoroughly before installation to ensure correct setup and to prevent damage or injury. Keep this manual for future reference.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | BEISHI |
| Model Number | BK-LB440 |
| Screen Size Suitable | 26-60 inch |
| Standard VESA | 100x100mm to 400x400mm |
| Maximum Load Weight | 40 kg |
| Adjustment Type | Full-Motion (Adjustable size) |
| Distance to Wall | 52mm (retracted) to 350mm (extended) |
| Tilt Angle | -10° to +15° |
| Swivel Angle | ±45° (left and right) |
| Level Adjustment | ±3° |
| Bubble Level | No |
Package Contents (Mounting Accessories)
Please verify that all components are present and undamaged before beginning installation.
- A: M4x20mm screws (4 pcs)
- B: M6x20mm screws (4 pcs)
- C: M8x20mm screws (4 pcs)
- D: D6 gaskets (4 pcs)
- E: Three-hole gaskets (4 pcs)
- F: Inner hexagonal wrench (1 pc)
- G: 5mm height-enhancing pads (4 pcs)
- H: M5x40mm screws (2 pcs)
- I: M6x50mm screws (4 pcs)
- J: M10x50mm screws (4 pcs)
Tools Required (Not Included)
- Spirit level
- Steel tape measure
- Phillips screwdriver
- Marking pencil
- Socket wrench
- Electric drill
- Wrench
- M10 drill bit
Safety Information and Precautions
- WARNING: Improper assembly or installation may result in serious injury, death, or property damage. Read all instructions and warnings carefully before assembly or installation.
- This mount is only suitable for solid load-bearing walls. For hollow walls, foam walls, wooden walls, or other special walls, professional installation is required.
- Ensure the wall can bear the weight of the TV and the mount before installation.
- It is recommended that this product be installed only by professional installers in accordance with the installation instructions.
- If you have questions or confusion about the installation information, please contact the seller.
- Do not assemble or install if any product or accessories are damaged or missing.
- For replacement parts or other needs, please contact your local dealer for assistance.
- Do not use this product for any purpose other than its designed use.
- This product is designed with sliding parts. For safety reasons, please use it with caution.
- This product contains small parts which may cause a choking hazard if swallowed. Keep out of the reach of infants and young children.
- For safety reasons, please check the product regularly (recommended at least every three months).
- The manufacturer will not be responsible for any damage or injury caused by modifying the product yourself, improper installation, or installing it beyond the specified limits.
- The maximum load-bearing capacity specified in the instructions, or improper use, may cause wear or damage to the product.
Setup and Installation
Refer to the installation diagram for visual guidance. A PDF version of the user manual with detailed diagrams is available here.
Step 1: Installation of Wall Bracket on Solid Wall
- Position the wall bracket on the desired location on the wall.
- Use a pencil to mark the holes where you intend to drill.
- Using an electric drill, drill 4 holes at the marked positions. The holes should be approximately 60mm deep.
- Note: This method is only applicable to solid load-bearing walls (e.g., concrete, brick). For hollow walls, foam walls, wooden walls, etc., professional installation is required. If the installation is performed by a professional, please install the accessories. Otherwise, it is not recommended to use.
Step 2: Installation of Hook and TV
- If needed, install the TV heightening pad (G) between the hook and the TV. This can be installed as shown in Figure A or on top of the hook as shown in Figure B in the manual diagram.
- Attach the hooks to the back of your TV using the appropriate A/B/C screws and three-hole gaskets (E) according to your TV's VESA pattern and screw diameter.
Step 3: Hang the TV on the Panel
- Carefully hang the TV (with the attached hooks) onto the wall mount panel.
- Once the TV is securely hung, fasten it with the safety screws (H) to prevent accidental dislodgement.
Step 4: Installation Completed
Once all steps are followed, your TV wall mount installation is complete.
Operating Instructions (Angle Adjustment)
The full-motion design allows for flexible viewing angles. Adjustments should be made carefully to avoid damage.
Pitch Adjustment (Tilt)
To adjust the vertical tilt angle of your TV (between -10° and +15°), loosen the side screws on the bracket, set to the desired angle, and then tighten the screws firmly.
Horizontal Adjustment (Swivel)
To adjust the horizontal swivel angle of your TV (up to ±45° left or right), adjust the screw on the back of the hook using an Allen wrench. The mount also allows for extension and retraction from the wall, ranging from 52mm to 350mm.
Maintenance
To ensure the long-term safety and stability of your TV wall mount, regular checks are recommended. Inspect the mount and all fasteners at least every three months for any signs of wear, loosening, or damage. Tighten any loose screws. Clean the mount with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
Troubleshooting
- TV is not level after installation: Use the level adjustment feature (±3°) as described in the operating instructions.
- Mount feels loose: Re-check all wall and TV attachment screws and ensure they are securely tightened. Refer to the installation steps.
- Difficulty adjusting angle: Ensure no cables are obstructing movement. Check if adjustment screws are too tight; loosen slightly before adjusting, then re-tighten.
- Missing or damaged parts: Do not proceed with installation. Contact the seller or your local dealer for assistance.
User Tips
When installing a TV, especially if you are unsure about the correct screw sizes for your specific TV model, it is highly recommended to consult your TV's manual or the manufacturer's support. Different TV brands and models may require specific screw types and lengths for VESA mounting. Having the correct screws is crucial for a secure and safe installation.
Warranty and Support
For warranty information, technical support, or to inquire about replacement parts, please contact the seller or the authorized dealer from whom you purchased this product. Ensure you have your purchase details and model number (BK-LB440) available when contacting support.
Additional Resources
A comprehensive user manual with detailed diagrams and instructions is available in PDF format. You can download it directly from the following link: