SNDWAY SW-523/SW-524

Contents

SNDWAY SW-523 SW-524 Digital Sound Level Meter

User Manual

Models: SW-523, SW-524

1. Introduction

This manual provides detailed instructions for the application, operation, and maintenance of the SNDWAY SW-523 and SW-524 Digital Sound Level Meters. Please read this manual thoroughly to ensure proper function and optimal performance of your device.

1.1. Important User Instructions

  • Do not use the device in flammable or explosive environments.
  • Used batteries should be disposed of according to national or local laws and regulations, not with normal household waste.
  • For any quality issues or operational doubts, please contact your local agent or the manufacturer for assistance.

1.2. Brief Overview

The SNDWAY SW-523 and SW-524 sound level meters are designed for measuring environmental noise in various settings. They are suitable for noise projects, quality control, and health prevention applications. Typical usage areas include industries, offices, traffic roads, homes, and for assessing noise from audio equipment, air conditioners, and refrigerators.

2. Detail Packing List

Please check the contents of your package against the list below. If any items are missing, contact your supplier.

NO. Item Unit QTY
1Sound Level MeterPC1
2Sponge BallPC1
3USB Data Cable (for SW-524 only)PC1
41.5V AAA BatteryPC3
5ManualPC1
6Warranty CardPC1
7Gift BoxPC1

3. Product Features and Parts

3.1. Key Features

  • Accuracy: ±1.5dB (based on 94dB@1KHz standard sound source).
  • Measurement Range: 30dB~130dB.
  • Frequency Response: 31.5Hz~8.5KHz.
  • Frequency Weighting: A-weighting and C-weighting.
  • Response Time: FAST and SLOW modes.
  • Measurement Modes: Max and Min.
  • Backlight: For use in dark conditions.
  • Data Hold: To freeze current readings.
  • Auto Shut-off: Device powers down after ten minutes of inactivity.
  • Analog Signal Output: AC and DC analog signal output.
  • Computer Connectivity (SW-524 only): USB data cable for connecting to a computer, downloading data records, real-time sampling, and printing charts/data.

3.2. Names of Parts

Diagram of SNDWAY Sound Level Meter with labeled parts and dimensions
Figure 1: Sound Level Meter Parts Diagram (SW-524 model shown)
  1. Sponge ball: Prevents wind interference.
  2. Condenser microphone sensor.
  3. Battery cover (located on the back).
  4. DC output: Noise digital signal output (10mV/dB, output impedance approx. 100 Ω).
  5. AC output: Noise analog signal output (output impedance approx. 600 Ω).
  6. USB port: For computer connection (SW-524 only).
  7. Adjustment switch: For calibration.
  8. LCD display screen.
  9. Control keys.

3.3. Key Functions

Key Icon Name Function
Power button iconPower (BACK)Short press to turn on, extended press to turn off.
MAX MINMax/MinShort press to test maximum, press again for minimum, press again for normal measurement.
A/CA/C WeightingShort press to switch between A and C weighting.
FAST SLOWResponse TimeShort press to switch between FAST and SLOW response times.
HOLDData HoldShort press to hold data, press again to return to normal data.
RECStorage RecordShort press to enter storage mode, press again to exit.
SETBacklight/SettingShort press to turn backlight on/off, extended press to set warning.

4. LCD Display

Detailed diagram of the LCD display with numbered indicators
Figure 2: LCD Display Indicators
  1. Noise reading
  2. dB unit
  3. Measurement range indicator
  4. Time weighting FAST indicator
  5. Time weighting SLOW indicator
  6. MAX (maximum value) indicator
  7. MIN (minimum value) indicator
  8. Measurement dynamic display
  9. Current time display
  10. FULL (storage full) indicator
  11. Low power indicator
  12. USB connecting computer indicator
  13. Storage mode indicator
  14. "OVER" warning: Lights when noise exceeds 130dB
  15. "UNDER" warning: Lights when noise is below 30dB
  16. Frequency weighting: A/C indicator lights when A/C weighting is selected.

5. Specifications

Parameter Value
Accuracy±1.5dB (at reference sound pressure level, 94dB@1KHz)
Frequency Response31.5Hz~8.5KHz
Dynamic Range50dB
Measurement Range30~130dBA, 35~130dBC
Frequency Weighting CharacteristicsA-weight and C-weight
Digital Display4 digits, resolution 0.1dB, sampling frequency 2 times/second (SW-523), 3 and a half (SW-524)
Dynamic Scale Display30~130dB (1 scale represents 2dB or 1dB)
Overload Indication"OVER" and "UNDER" Symbolic representation
AC Signal OutputYes
DC Signal OutputYes
Response TimeFAST (fast) and SLOW (slow)
Microphone6mm condenser microphone
Size Value LockMAX and MIN
Battery3x1.5V AAA
Working Temperature and Humidity0°C~40°C, 10%~80%RH
Storage Temperature and Humidity-10°C~60°C, 10%~70%RH
Time DisplayYes (SW-524 only)
Storage Function1 record/second, continuous storage for 17 hours (SW-524 only)
Communicate with ComputerCommunication via MicroUSB (SW-524 only)
Alarm FunctionHigh limit alarm can be set (SW-524 only)
Size215mm*63.5mm*27mm
Comparison table of specifications for SW-523 and SW-524 models
Figure 3: SW-523 vs SW-524 Specifications Comparison

6. Setup

6.1. Battery Installation

To install batteries, open the battery cover located on the back of the meter. Insert three 1.5V AAA batteries, ensuring correct polarity. Close the battery cover securely.

Diagram showing battery installation in the sound level meter
Figure 4: Battery Installation

6.2. Computer Connection (SW-524 only)

The SW-524 model supports connection to a computer for advanced functions such as downloading recordings, real-time sampling, and printing charts and data. The necessary software package is typically provided as a 'NoiseMeter.rar' file. After unzipping, refer to the installation and operation instructions within the software package before proceeding.

Diagram showing USB cable connection from sound level meter to computer, with data storage details
Figure 5: USB Cable Connection and Data Storage Overview

The software allows for data storage every minute, continuous storage for up to 17 hours, and continuous coexistence of data up to 61200 groups.

Screenshot of NoiseMeter software showing USB connection status and menu options
Figure 6: NoiseMeter Software - USB Connection Status

To monitor data in real-time, click the relevant icon in the software (e.g., 'real time sampling'). The software acquires data from the instrument every second.

Screenshot of NoiseMeter software displaying real-time data monitoring with a graph and table
Figure 7: NoiseMeter Software - Data Monitoring Interface

The software also provides an interface for exporting and downloading recorded data.

Screenshot of NoiseMeter software showing the export and download page for recorded data
Figure 8: NoiseMeter Software - Export/Download Page

7. Operation

7.1. Noise Measurement

Press the Power key to turn on the device. After approximately two seconds, the meter will enter measurement mode, and the noise reading will be displayed on the screen.

Screenshots showing noise measurement readings, including UNDER and OVER indicators
Figure 9: Noise Measurement Display
  • If the reading is below 30dB, the "UNDER" indicator will light up.
  • If the reading is over 130dB, the "OVER" indicator will light up.

7.2. Warning Setting (SW-524 only)

To set a warning value, perform an extended press on the SET key. The screen will display "AL" flashing along with the current warning value. Use the HOLD or REC keys to adjust the warning value. An extended press on either of these keys will increase the adjustment range. Short press the SET key to store the new warning value, or short press the Power (BACK) key to cancel the setting mode.

Note: The warning value will reset to 130dB every time the device is turned on to prevent misoperation.

When the noise being tested exceeds the set warning value, the meter will emit a "beep beep beep" sound and stop testing, with the tested value flashing on the screen. Testing will resume once the warning sound stops. If the noise remains above the warning value, the warning sound will continue.

Diagram showing the alarm upper limit value customization feature
Figure 10: Alarm Upper Limit Value Customization

7.3. Frequency Weighting

The meter offers two types of frequency weighting:

  • A-weighting: Simulates the frequency characteristics of low-intensity noise (below 55dB), primarily used for civil applications like environmental noise testing in residential areas.
  • C-weighting: Simulates the frequency characteristics of high-intensity noise, mainly for industrial measurements such as noise in aircraft industries or engine noise.

Upon turning on, the meter defaults to A-weighting. Short press the A/C key to switch to C-weighting.

Diagram explaining A-weighted for ambient noise and C-weighted for mechanical noise
Figure 11: AC Double Weighting Explanation

7.4. Response Time

The meter has two response modes:

  • FAST mode: Suitable for circumstances where noise changes rapidly, closely mimicking the reaction of human ears. This is the default mode upon turning on.
  • SLOW mode: Ideal for steady noise conditions.

Short press the FAST/SLOW key to switch between FAST and SLOW modes.

7.5. Measurement Mode (MAX/MIN)

After turning on, the meter begins normal noise testing. Short press the MAX/MIN key to enter maximum measurement mode. Press it again to enter minimum measurement mode. Pressing it a third time will return to general measurement mode.

7.6. Data Hold

Short press the HOLD key to freeze the current reading on the display. Short press it again to release the data hold and resume live measurement.

7.7. Data Storage (SW-524 only)

Short press the REC key to enter storage mode. The device will store a set of data every second, and the REC indicator will flash. The meter can continuously store data for up to 17 hours. If the storage memory becomes full, the FULL indicator will flash. To clear the storage, short press the Power (BACK) key. While in storage mode, A/C weighting conversion, FAST/SLOW mode changes, MAX/MIN mode, and data hold functions are unavailable.

7.8. Time Setting (SW-524 only)

Perform an extended press on the SET key to enter the warning value setting mode. Short press it again to enter the time setting mode. The display will show the year, month, and day flashing. Use the HOLD or REC keys to adjust the values. Short press the SET key to store the current setting and move to the next parameter (e.g., from year to month). During the setting process, you can short press the Power (BACK) key to exit.

8. Device Adjustment (Calibration)

This device is factory-adjusted. However, it may require adjustment if it has been unused for a long period or if the sensor has been changed. It is recommended to adjust the device annually using a standard 94dB@1KHz sound source.

  1. Conditions Setting: Set the meter to A-weighting, FAST response time, and the 30~130dB measurement range.
  2. Microphone Placement: Carefully insert the microphone into the hole of the standard sound source.
  3. Adjustment: Turn on the sound source and adjust its output to 94dB. Use a small slot-type screwdriver to adjust the calibration knob located inside the hole on the bottom of the device until the screen displays 93.8dB.

9. Maintenance

9.1. Battery Replacement

  • If the device will not be used for an extended period, remove the batteries to prevent corrosion from leakage.
  • Replace batteries as soon as possible if the low power indicator is shown on the screen.

9.2. Surface Cleaning

Avoid using ethyl alcohol or other diluents as they can have a corrosive effect on the device's body surface. Instead, gently clean the device with a soft, damp cloth.

10. Common Problems

10.1. No Readings on Screen

  • No power or damaged batteries: Replace the batteries.

10.2. No Connection with Computer (SW-524 only)

  • USB data cable damaged: Replace the USB data cable.
  • Computer ports damaged: Try connecting to a different USB port on your computer.
  • No Windows system: The software requires Windows (XP, Win7, Win8, Win10). Ensure your computer meets this requirement.
  • USB port of the device damaged: Contact factory service for repair.

11. User Tips

Based on general usage and common inquiries:

  • Always ensure the sponge ball is properly attached to the microphone to minimize wind noise, especially when measuring outdoors.
  • For consistent readings, try to maintain a consistent distance and angle between the meter's microphone and the noise source.
  • When comparing noise levels, use the same frequency weighting (A or C) and response time (FAST or SLOW) settings for all measurements.
  • If using the SW-524 with computer software, regularly back up your stored data to prevent loss.

12. Warranty and Support

This product comes with a warranty card included in the package. Please refer to the warranty card for specific terms and conditions regarding warranty coverage. For technical support, service, or inquiries, please contact your local distributor or the manufacturer directly.

A PDF version of the user manual is available for download. You can find it at: User manual (PDF).

13. Product Video

Video: Demonstration of the SNDWAY Digital Sound Level Meter's features and operation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.