POKESS BB5Z7825324B BB5Z7825325B

Contents

POKESS Window Door Molding Weatherstrip Seal

User Manual for Ford Explorer 2011-2019

1. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

2. Product Overview

This product is a replacement window door molding weatherstrip seal designed for specific Ford Explorer models. It helps to seal the window against water, wind, and noise, restoring the original integrity of your vehicle's door system.

Pair of POKESS weatherstrip seals
Figure 1: POKESS Window Door Molding Weatherstrip Seal (Pair)
Illustration demonstrating the soft and elastic nature of the weatherstrip material.
Figure 2: Material Flexibility Demonstration

3. Setup and Installation

3.1 Pre-Installation Check

  1. Verify OE Number: Confirm the OE number of this part (BB5Z7825324B or BB5Z7825325B) is 100% identical to your original broken part. If the OE number is incorrect, do not install and contact the seller immediately.
  2. Check Package Contents: Ensure the package contains the main part(s) and any necessary accessories or hardware.
  3. Confirm Vehicle Match: Verify that your vehicle model (Ford Explorer), year (2011-2019), and the intended installation position (rear left or right side) match the product.
Close-up comparison of a worn weatherstrip seal and a new one
Figure 3: Worn vs. New Weatherstrip Seal

3.2 Installation Procedure

Installation typically involves removing the old, worn seal and snapping the new one into place. While professional installation is recommended, many users find this a straightforward DIY task.

  1. Prepare the Area: Ensure the window and door frame area is clean and free from debris.
  2. Remove Old Seal: Carefully pry out the old weatherstrip seal. A flathead screwdriver can be used gently to assist in removal, taking care not to damage the paint or surrounding trim.
  3. Install New Seal: Align the new weatherstrip seal with the channel on the door. Press firmly along its length until it snaps securely into place. Ensure it is fully seated and flush with the door frame.
  4. Test Fitment: Operate the window several times to ensure smooth movement and proper sealing. Check for any gaps or misalignments.
Diagram showing the length of both left (L) and right (R) weatherstrip seals, each measuring 730mm.
Figure 4: Left (L) and Right (R) Seal Dimensions (730mm)

4. Operating and Function

Once installed, the weatherstrip seal functions passively to:

  • Seal Against Elements: Prevent water, wind, and dust from entering the vehicle cabin through the window gap.
  • Reduce Noise: Minimize road noise and wind whistle for a quieter ride.
  • Protect Interior: Guard against moisture damage to interior components.
  • Support Window Operation: Provide a smooth guide for the window glass as it moves up and down.

5. Maintenance

To ensure the longevity and effectiveness of your weatherstrip seals:

  • Regular Cleaning: Periodically clean the seals with a mild soap and water solution to remove dirt and grime. Avoid harsh chemicals that can degrade the rubber.
  • Inspection: Routinely inspect the seals for cracks, tears, hardening, or signs of wear. Damaged seals should be replaced promptly to maintain proper sealing.
  • Lubrication (Optional): Some automotive rubber conditioners or silicone sprays can help keep the rubber pliable and prevent sticking, especially in extreme temperatures. Apply sparingly as per product instructions.

6. Troubleshooting

Common Issues and Solutions:

Problem Possible Cause Solution
Water Leakage / Wind Noise Improper installation; Seal not fully seated; Damaged seal. Re-check installation to ensure the seal is fully seated. Inspect for damage and replace if necessary.
Window Sticks / Hard to Roll Up/Down Seal misalignment; Dirt/debris in the window channel. Ensure the seal is correctly aligned. Clean the window channel thoroughly.
Seal Does Not Fit Properly Incorrect part for vehicle model/year; Manufacturing defect. Double-check OE numbers and vehicle compatibility. Contact seller if fitment issues persist.

7. Specifications

Feature Detail
Brand POKESS
OEM Part Numbers BB5Z7825324B (Right Side), BB5Z7825325B (Left Side)
Compatibility Ford Explorer 2011-2019
Material Durable, soft, and elastic rubber compound
Length (Each Seal) Approximately 730mm (28.7 inches)
Origin Mainland China
Package Dimensions (approx.) 20cm (L) x 10cm (W) x 10cm (H)
Package Weight (approx.) 0.25 kg

8. User Tips

  • Easy Replacement: Many users report that replacing these seals is a simple process, often requiring just a flathead screwdriver to gently pry out the old seal before snapping the new one into place.
  • Common Issue: If your original rubber seals are torn or degraded, replacing them with these parts can significantly improve your vehicle's sealing and reduce noise.
  • Verify Fitment: Always double-check the OE numbers and confirm your Ford Explorer's year (2011-2019) to ensure perfect compatibility. This product is specifically designed for Ford Explorer and is not compatible with other models like Volvo V40 Cross Country 2014.

9. Warranty and Support

For specific warranty information, please refer to the terms and conditions provided by your retailer or contact the seller directly. If you encounter any issues or have questions regarding the product, please reach out to the seller for assistance.

A detailed user manual in PDF format may also be available from the seller for additional guidance.

© 2024 POKESS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.