1. Introduction
Thank you for purchasing the M7AC balance charger. Please read this manual carefully before use to ensure proper operation and safety.
Key Points
- Tips: Helpful advice for optimal use.
- Important: Critical information for safety and functionality.
- Information: General details and explanations.
Further Information
To ensure you have the best experience with this product, visit the official ToolkitRC website for news, information, and firmware updates. The official website is www.toolkitrc.com.
2. Safety Information
WARNING: Failure to follow these safety instructions may result in fire, injury, or damage to the product or property.
- The M7AC charger allows an input voltage of DC 7-28V or AC 100-240V. Ensure the charger is only connected to a suitable power source and with correct polarity.
- Do not use this product in hot, humid, flammable, or explosive environments.
- Please do not use this charger without supervision. Never leave charging batteries unattended.
- When not using this product, please unplug the input power.
- When using the charging function, please set a current that matches the battery. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
3. Product Description and Features
The M7AC is a multifunctional tool that integrates functions such as a balance charger and discharger, a signal measuring device, and a signal source.
- Supports AC100W or DC300W dual input.
- Charges, discharges, and balances (where applicable) LiPo, LiHV, LiFe, Lion, LTO 1-6S, NiMh 1-16S, PB 1-10S batteries.
- Charge current: MAX 15A @MAX300W.
- Discharge current: Recycle / External mode Max 15A @300W; Internal mode Max 3A @15W.
- Lithium battery cut-off voltage can be adjusted (TVC function).
- Measures battery voltage, battery internal resistance, and balances lithium packs automatically.
- Measures / outputs PWM/PPM/SBUS standard signals with an accuracy of 1 microsecond.
- Constant current and constant voltage source output, customizable 1-28V constant voltage, 0.5-15A constant current.
- Can be adapted for charging consumer-grade drone batteries.
- Multi-language user interface and voice broadcast, with customizable voice packs.
- Easily upgradable via USB.
4. M7AC Layout and Components
Familiarize yourself with the different parts of your M7AC charger:

Figure 1: M7AC Charger Layout Diagram
This diagram illustrates the front and back panels of the M7AC charger, highlighting all ports, buttons, and indicators for easy identification.
Front Panel:
- Display: TFT IPS LCD screen for information and settings.
- Scroll Wheel: For navigation and value adjustment.
- Exit Button: To go back or exit menus.
- USB Output (5.0V 2.1A): For charging external devices.
- Balance Port (2-6S): For balancing multi-cell batteries.
- Signal Port: For signal measurement and output.
- Output Ports (XT60/XT30): Main charging/discharging ports.
- TF Card Slot: For firmware upgrades and custom files.
- Speaker: For audio alerts and voice broadcasts.
Back Panel:
- DC Input (7-28V): For DC power supply.
- Cooling Fan: For heat dissipation.
- AC Input (100-240V): For AC power supply.
- AC Switch: Power on/off switch for AC input.
5. Setup and Quick Start
Follow these steps to quickly set up and start using your M7AC charger:
Video 1: M7AC Unboxing and Basic Operation
This video demonstrates the unboxing process and initial power-on sequence of the ToolkitRC M7AC charger, including navigating the basic menu.
- Connect Power: Connect a 7-28V DC power supply or an AC 100-240V power cable to the input port on the back of the M7AC.
- Power On: If using AC, ensure the AC switch is in the 'On' position. The display will show the boot logo for 2 seconds.
- Welcome Sound: A welcome sound (dependent on the installed voice pack) will play.
- Main Interface: After booting, the screen will enter the main interface, displaying current voltage, power, temperature, and cell voltages.

Figure 2: M7AC Main Display Screen
This image shows the M7AC charger's main display during operation, indicating input voltage, total power, temperature, and individual cell voltages.
Basic Navigation:
- Auxiliary Function Interface: Press and hold [Exit] to enter the auxiliary function interface.
- Switch Pages: Scroll the [Scroll Wheel] to switch between different display pages.
- Set Charging Parameters: With the charger idle, short press [OK] to set charging parameters. During charging, press [OK] to adjust amperage or stop the charge.
- System Settings: With the charger idle, press and hold [OK] to enter the system setting interface.
- Return: Short press [Exit] to return to the previous interface.
6. Operating Instructions: Charge and Discharge Settings
To begin charging or discharging, navigate to the main interface, select the desired battery profile, and press [OK].
6.1. Battery Type Setting
From the main interface, select 'Battery selection' and press [OK]. Scroll the [Scroll Wheel] to choose from presets or create a new battery profile (up to 32 profiles). Press [Enter] to configure a specific battery setting.
WARNING: Ensure the correct battery type is selected before charging. Incorrect selection can damage the battery or cause fire.
Supported Battery Types:
- LiPo: Lithium Polymer (Nominal 3.70V, Full 4.20V)
- LiHV: High-Voltage Lithium (Nominal 3.85V, Full 4.35V)
- LiFe: Iron-Lithium (Nominal 3.30V, Full 3.60V)
- Lion: Lithium-Ion (Nominal 3.60V, Full 4.10V)
- LTO: Lithium-Titanate (Nominal 2.40V, Full 2.70V)
- NiMh: Nickel-Metal Hydride (Nominal 1.20V)
- PB: Lead-Acid (Nominal 2.00V)
- Smart Battery Mode
6.2. Cell Setting
In the battery profile, move the cursor to 'Cells' and press [OK] to modify the number of cells (1S to 6S). You can also set it to 'Auto' for automatic cell count detection via the balance port. Ensure the cell count is correct to prevent overcharging.
6.3. Work Mode
Select 'Mode' and press [OK] to choose the desired operation:
- Charge: Standard charging.
- DisCHG: Discharging.
- StoCHG: Storage charging/discharging (for optimal battery longevity).
NiMh and PB batteries support Charge and Discharge. Lipo, LiHV, LiFe, Lion, LTO support all three modes.
6.4. Discharge Mode
When 'DisCHG' or 'StoCHG' is selected, you can choose the discharge mode:
- Inter (Internal): Discharges using internal heat dissipation (Max 3.0A@15W).
- Recycle: Recovers power to the input battery (Max 15.0A@300W).
- External: Discharges through an external load connected to the input port (Max 15.0A@300W).
6.5. Max Input Voltage (for Recycle Mode)
If 'Recycle' discharge mode is selected, set the 'Max Input Vol.' to prevent overcharging the input battery. The charger will stop discharging if this voltage is reached.
6.6. End Voltage Setting (TVC - Terminal Voltage Control)
Adjust the 'End Voltage' for individual cells. This is the charge cut-off voltage (±50mV of full voltage) or discharge cut-off voltage. Only applicable for LiPo, LiHV, LiFe batteries.
6.7. Current Setting
Set the 'Charge Current' or 'DisCHG Current' (0.1A increments, up to 10.0A). It's recommended to set the charging rate to 1-2C based on battery capacity (e.g., 2000mAh battery = 2.0-4.0A).
6.8. NiMH Setting (PeakV)
For NiMH batteries, set the 'PeakV' value (5mV-15mV). This is the maximum voltage drop per cell when the battery is fully charged, indicating the end of charge.
6.9. Cycle Setting (for NiMh)
In 'Cycle' mode for NiMh batteries, set 'Cycle times' (2-12) and 'Rest time' (2-10 minutes) between charge/discharge cycles.
6.10. External Load Setting
When 'External' discharge mode is selected, set the wattage according to the external load used.
6.11. Smart Battery Setting (UAVbat)
If 'UAVbat' is selected as the battery type, configure 'Drone model' (e.g., Mavic2, MavicS, Phantom, Inspire) and 'Max Current' (0.5A to 15A).
6.12. Charge and Discharge Work (Monitoring)
Once charging/discharging starts, the display shows real-time data: input voltage, accumulated power, internal temperature, main port voltage/current, working time, charged capacity, and individual cell voltages. Scroll the [Scroll Wheel] to toggle between different display pages showing internal resistance and general information.
IMPORTANT: Never leave cells unattended during charging/discharging. For lithium batteries, balancing only occurs if the balance plug is connected.
7. Advanced Functions (Accessibility)
From the main interface, long press [Exit] to enter the auxiliary function interface.
7.1. Measure Resistance
Short press [OK] to test the internal resistance of the connected battery.
7.2. Measure Signal
Enter this mode to measure PWM, PPM, or SBUS signals. Scroll the [Scroll Wheel] to select the signal type and view real-time signal data.
7.3. Signal Output
Enter this mode to output PWM, PPM, or SBUS signals. For PWM, you can set manual or auto modes, adjusting pulse width (800-2200us) and cycle (2.5ms-50.0ms). For PPM/SBUS, adjust individual channel pulse widths.
7.4. ESC Test
Select 'ESC test' and press [OK]. Scroll the [Scroll Wheel] to adjust pulse width/cycle to test your Electronic Speed Controller.
7.5. Power (Adjustable Power Supply)
The M7AC can act as an adjustable power supply. Set the desired output voltage (up to 28V) and current (up to 15A). Press [OK] to start power output.
8. System Settings
From the main interface, long press [OK] to enter the system settings.
8.1. Input Settings
- Power Select: Preset power profiles.
- Power Type: Choose 'Battery Pack' (enables recycle mode) or 'Adapter' (disables recycle mode).
- Max Power: Maximum wattage allowed via input.
- Max Current: Maximum current allowed via input.
- Voltage Range: Input voltage range.
8.2. Security Settings
- Safe Inter Temp.: Internal temperature limit (charger stops if exceeded).
- Safe Exter Temp.: External temperature limit (charger stops if exceeded).
- Safe Time: Maximum continuous operation time limit.
- Safe Capacity: Maximum accumulated capacity limit.
8.3. Personalization
- Backlight: Display brightness (1-10).
- Operation Volume: Scroll wheel sound volume (Off, Low, Medium, High).
- Announce Volume: Menu readout volume.
- Warning Volume: Warning tone volume.
- Language: System display language (English, Chinese, etc.).
- Theme Style: Light or Dark theme.
8.4. Other System Options
- Battery Selection: Show/hide frequently used parameters.
- Work Completed: Stop or trickle charge after completion.
- Balance Start Vol.: Balance cells prior to full current charge.
- Continuous Work: Enables/disables continuous charging/discharging after battery replacement.
- Default: Restore factory settings.
- ID: Independent ID for each device.
9. Customize Function
The M7AC supports customizable boot images and voice packs using a TF card (128MB-16GB).
9.1. Boot Image
Insert a TF card into the slot, connect the charger to a computer via USB-A. The computer will show two USB drives. One is for firmware, the other for custom files. Place a logo.bmp file (240x320 pixels) in the LOGO folder on the custom files drive. When the M7AC powers on, it will display this image.
9.2. Broadcast Voice
Voice files are stored in the SOUNDS folder, organized by language (e.g., CHI, ENG, DEU). These are WAV files (Mono format). You can customize these files to change the charger's voice prompts.
10. Other Functions
10.1. Firmware Upgrade
Connect the M7AC to your computer via USB. Download the app.upg file from the official ToolkitRC website and overwrite the file in the 'Toolkit' USB drive to upgrade the firmware.
10.2. USB Output
The Type-A USB port provides 5.0V 2.0A output for charging mobile devices.
10.3. Automatically Continue Charging/Discharging
When a battery is fully charged, connect the next battery, and the device will automatically continue the process. This function can be enabled/disabled in system settings.
10.4. Fan Level
- Above 45°C: Fan runs at half speed.
- Above 53°C: Fan runs at full speed.
10.5. Manual Voltage Calibration
With the charger off, press and hold the [roller], then connect power. The system enters calibration mode. Use a voltmeter to measure actual cell voltages and adjust the displayed values to match. Save to apply.
10.6. Full Charge Mode
When a lithium battery is fully charged, it prompts 'Fast charge complete'. If the battery remains connected, the charger will trickle charge until disconnected.
11. Maintenance
The ToolkitRC M7AC charger is designed for durability. To ensure its longevity and optimal performance:
- Cleaning: Use a soft, dry cloth to clean the exterior of the charger. Do not use liquid cleaners or solvents.
- Storage: Store the charger in a cool, dry place away from direct sunlight, extreme temperatures, and humidity.
- Handling: Avoid dropping the charger or subjecting it to strong impacts.
- Ventilation: Ensure the cooling fan vents are clear of obstructions during operation to prevent overheating.
12. Troubleshooting
- Charger Not Powering On: Check power connections (AC or DC). Ensure the AC switch is on if using AC power. Verify input voltage is within the specified range (DC 7-28V, AC 100-240V).
- Battery Not Charging: Verify battery type and cell count settings match the connected battery. Check that the battery is properly connected to the output port and balance port (if applicable). Ensure charging current is set appropriately.
- Error Messages: Refer to the display for specific error codes or messages. Common errors relate to incorrect battery type, over-voltage, under-voltage, or temperature warnings. Consult the manual sections for relevant settings.
- Overheating: Ensure the charger's cooling fan vents are not blocked. Operate the charger in a well-ventilated area. Reduce charging current if overheating persists.
- Inaccurate Readings: If voltage or resistance readings seem off, consider performing a manual voltage calibration (see Section 10.5).
13. User Tips
- Intuitive Menu: The M7AC features an intuitive menu system. Take some time to explore the settings using the scroll wheel and OK/Exit buttons to familiarize yourself with its capabilities.
- Easy Operation: Many users find the M7AC easy to operate once familiar with the basic navigation. Start with simple charging tasks and gradually explore advanced functions.
- Firmware Updates: Regularly check the ToolkitRC website for firmware updates to ensure you have the latest features and bug fixes.
- Balance Charging: Always use the balance port when charging multi-cell lithium batteries for safety and to maximize battery life.
14. Specifications
| Category | Parameter | Value |
|---|---|---|
| Input | AC Input | 100-240V @MAX 100W |
| DC Input | 7-35V @MAX20A | |
| Battery Type | Supported Types | LiPo, LiHV, LiFe, Lion, LTO (1-6S); NiMh (1-16S); PB (1-10S) |
| Balance Current | 800mA @4.2V | |
| Charge | Accuracy | <0.005V |
| Power | 0.1-15A @300W | |
| Discharge Power | 0.1-15A @300W (Rec/Ext Mode); 0.1-3A @15W (Internal Mode) | |
| Output | USB A | 5.0V @10W or upgrade |
| Voltage | 1.0V-5.0V @1-6S | |
| Internal Resistance | Measurement Range | 0.1mΩ-99mΩ @1-6S |
| Measure Signal | PWM | 880us-2200us @20-400hz |
| PPM | 880us-2200us*8 CH @20-50hz | |
| SBUS | 880us-2200us*16 CH @20-100hz | |
| Output Signal | PWM | 500us-2500us @20-1000hz |
| PPM | 880us-2200us*8 CH @50hz | |
| SBUS | 880us-2200us*16 CH @74hz | |
| Power | 0.5-15A @1-28V Mode: CC+CV | |
| Display | LCD | IPS 2.4 inch 320*240 resolution |
| TF Card | Support 128MB-16GB | |
| Product | Size | 112mm*73mm*38mm |
| Weight | 245g | |
| Individual Packing | Size | 144mm*125mm*43mm |
| Weight | 380g |
15. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or visit the official ToolkitRC website at www.toolkitrc.com. Please retain your proof of purchase for warranty claims.