Ligghig E27 303 Switch Wire Plug

Contents

E27 Lamp Holder with 303 Switch Power Cord

Model: E27 303 Switch Wire Plug

Brand: Ligghig

1. Introduction

Thank you for purchasing the Ligghig E27 Lamp Holder with 303 Switch Power Cord. This product is designed to provide a convenient and safe power solution for low-power indoor lighting applications. It features a standard E27 screw socket, an integrated on/off switch, and a European (EU) 2-pin plug.

2. Safety Instructions

Please read all safety instructions carefully before use to prevent electric shock, fire, or injury.

  • This plug light cable is suitable for indoor use only. It is strictly prohibited from being used in damp places such as bathrooms.
  • If outdoor use is absolutely necessary, avoid prolonged exposure to direct sunlight and ensure adequate waterproofing and rain protection.
  • Always ensure the power source is turned off before installing or replacing a light bulb.
  • Do not exceed the maximum wattage rating of 60W for the connected bulb.
  • Inspect the cord and lamp holder for any signs of damage (frayed wires, cracks) before each use. Do not use if damaged.
  • Special Reminder for Bulb Installation: The two elastic tabs inside the E27 lamp head should not be forcibly bent or wrenched. They are designed with one vertical and one angled at approximately 45 degrees. Forcing them may cause a short circuit, damaging the lamp head wiring or causing the bulb to burn out.
  • Keep out of reach of children.

3. Package Contents

  • 1 x E27 Lamp Holder with 303 Switch Power Cord (1.8m length)

4. Setup

  1. Ensure Power is Off: Before beginning, make sure the power outlet you intend to use is switched off or unplugged.
  2. Install Light Bulb: Carefully screw an E27 base light bulb (max 60W) into the lamp holder socket. Ensure the bulb is securely seated but do not overtighten. Refer to the image below for the internal contacts.
    Close-up of E27 socket interior showing folding elastic contacts and a warning about not bending them.
    Figure 1: E27 Socket Interior with Folding Elastic Contacts. Do not force or bend these contacts.
  3. Connect to Power: Insert the EU 2-pin plug into a suitable power outlet.
  4. Ready for Use: The lamp holder is now ready to be operated using its integrated switch.

5. Operating Instructions

The lamp holder features a convenient 303 on/off switch located along the power cord. To operate:

  • Press the switch button once to turn the connected light bulb ON.
  • Press the switch button again to turn the connected light bulb OFF.
Diagram showing the E27 screw head for replaceable bulb and the manual switch design.
Figure 2: E27 Screw Head and Manual Switch Design.

6. Maintenance

  • Cleaning: Always unplug the lamp holder from the power outlet before cleaning. Wipe the surface with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
  • Inspection: Periodically inspect the power cord, plug, and lamp holder for any signs of wear, damage, or loose connections. Replace the product if any damage is found.
  • Storage: When not in use, store the lamp holder in a dry, cool place away from direct sunlight and moisture.

7. Troubleshooting

  • Light does not turn on:
    • Check if the light bulb is securely screwed into the E27 socket.
    • Ensure the light bulb is not faulty (test with another bulb if possible).
    • Verify that the power plug is fully inserted into a working electrical outlet.
    • Confirm the 303 switch is in the 'ON' position.
  • Light flickers:
    • Ensure the light bulb is screwed in tightly.
    • Check for stable power supply from the outlet.
    • If flickering persists, the bulb might be faulty or incompatible.
  • Short circuit occurs during bulb installation:
    • This can happen if the internal elastic contacts of the E27 socket are bent or forced. Always handle with care during bulb installation.

8. Specifications

Parameter Value
Product Name E27 303 Switch Cord and Plug
Color Options Black, White
Operating Voltage 0-250V AC (Rated for 220V AC systems)
Rated Frequency 50/60Hz
Plug Type European (EU) 2-pin
Lamp Holder Type E27 Screw Socket
Max. Wattage 60W
Wire Length 1.8 meters
Base Material ABS
Wire Core Copper
Table of specifications for E27 303 Switch Cord and Plug, showing voltage, current, length, and color.
Figure 3: Product Specifications Overview.
Diagram showing dimensions of the E27 socket, 303 switch, and EU plug.
Figure 4: Product Dimensions.

9. User Tips

  • Verify Wire Length: Always confirm the actual wire length upon receiving your product, as some product titles or descriptions may vary from the detailed specifications. This model features a 1.8-meter wire.
  • Bulb Compatibility: Ensure your chosen light bulb is compatible with an E27 screw base and does not exceed the 60W maximum wattage.

10. Warranty and Support

For any questions, technical support, or warranty claims, please contact the seller or retailer from whom you purchased this product. Please retain your proof of purchase for any warranty-related inquiries.

11. Product Video

Product showcase video demonstrating the E27 Lamp Holder with 303 Switch Power Cord.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.