1. Introduction
This manual provides detailed instructions for the safe and effective use of your TOPPING B200 Single Channel Pure Rear Stage Amplifier. Please read this manual thoroughly before operating the device and retain it for future reference.
The TOPPING B200 is an ultra-high performance mono pure power amplifier designed for HiFi audio systems, delivering high power output with low noise.
2. Package Contents
Please check that all items are present in the package:
- B200 Host x 1
- AC to DC Power Adapter x 1
- AC Cable x 1
- Product Information Card x 1
- 12V Trigger Cable x 1
Image showing the TOPPING B200 amplifier and some accessories, illustrating typical package contents.
3. Product Overview
Front Panel
Front panel of the B200 amplifier, featuring the power/input switch and input indicators.
- Power & Input Switch: Press briefly to turn on or select other inputs. Press and hold to turn off.
- Input Indicator: Displays the currently selected input.
Rear Panel
Rear panel of the B200 amplifier with various connection ports for audio input, speaker output, power, and trigger.
- Mono Balanced Combo Input (IN1-3): Accepts XLR or 6.35mm TRS connections.
- + Speaker Output (4mm jack): Positive speaker terminal.
- - Speaker Output (4mm jack): Negative speaker terminal.
- Power Input (DC64V): Connect the provided power adapter here.
- Firmware Upgrade Interface: For firmware upgrades only.
- Gain Setting:
- H: High gain
- L: Low gain
- 12V Trigger In (3.5mm jack): Connect to a device with a 12V Trigger out jack to control the B200's power on/standby.
4. Setup
4.1 Connecting to the Input Source
Use TRS or XLR cables to connect your preamplifier or audio source to the B200's input jacks (IN1-3) on the rear panel. Refer to the rear panel overview for port locations.
For a visual guide on connecting input sources, please refer to page 5 of the User Manual PDF.
4.2 Connecting 12V Trigger
If you have a device with a 12V Trigger output, connect it to the B200's 12V Trigger In jack (9) on the rear panel using the provided cable. This allows the connected device to control the B200's power state (on/standby).
For a visual guide on connecting the 12V trigger, please refer to page 5 of the User Manual PDF.
4.3 Connecting Passive Speakers
The B200 features speaker terminals (4, 5) on the rear panel that support direct insertion (banana plugs), bare wire, or Y-terminals.
Direct Insertion (Banana Plugs):
- Tighten the crystal case clockwise.
- Insert the banana plug into the end of the corresponding terminal.
Bare Wire / Y-Insertion:
- Unscrew the crystal case counterclockwise.
- For bare wire, insert stripped metal speaker wires into the round holes in the copper posts. For Y-terminals, insert them around the periphery of the posts.
- Important: Do not let bare speaker wires touch each other or the case of this unit. This could damage the unit and the speakers.
- Finally, tighten the crystal case clockwise.
For a visual guide on connecting passive speakers, please refer to page 6 of the User Manual PDF.
5. Operating Instructions
Once all connections are made, ensure the power adapter is securely connected to the B200 and a power outlet.
- Power On/Off: Briefly press the Power & Input Switch (1) on the front panel to turn on. Press and hold to turn off.
- Input Selection: After powering on, briefly press the Power & Input Switch (1) to cycle through available inputs. The Input Indicator (2) will show the selected input.
- Gain Setting: Use the Gain Setting switch (8) on the rear panel to select between High (H) or Low (L) gain, depending on your system's requirements and speaker sensitivity.
6. Maintenance
- The output jacks shall not be grounded or short-circuited.
- Do not keep the unit in a hot, humid environment or hit the unit strongly.
- Opening the case instantly voids the warranty. Any repairs should be handled by professional service personnel.
- This product is for indoor use only.
- Clean the unit with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
7. Troubleshooting
If you encounter problems during use, please refer to the following common issues and solutions:
- No Sound:
- Check all cable connections (input, output, power).
- Ensure the B200 is powered on and the correct input is selected.
- Verify that your source device and speakers are functioning correctly.
- Check the gain setting; ensure it's appropriate for your system.
- Distorted Sound:
- Ensure input levels are not too high, causing clipping.
- Check speaker connections for loose wires or short circuits.
- Verify that the gain setting is not excessively high.
- Unit Does Not Power On:
- Check the power adapter connection and ensure the power outlet is active.
- If using the 12V trigger, ensure the controlling device is powered on and sending a trigger signal.
For further assistance, you can visit the official TOPPING FAQ page: https://www.toppingaudio.com/faq
If problems persist, please contact customer support at service@tpdz.net.
8. Specifications
The following table details the key specifications of the TOPPING B200 Power Amplifier:
| Parameter | Value (BAL) |
|---|---|
| Measured Dimensions (including protruding parts) | 22.0cm x 18.5cm x 9.2cm |
| Weight | 2.74Kg |
| Power Input | DC 64V/3.75A (3 pin aviation connector) |
| Signal Input | 3 x Mono (Combo: XLR + 6.35mm TRS) |
| Signal Output | Speaker terminal (BTL output) |
| Other Connectors | 12V Trigger In (3.5mm jack), Type-C FW port |
| Gain | Two types (H/L) |
| Display | White LED |
| Standby Power Consumption | <1.2W |
| THD+N @1kHz (A-wt) | <0.00008% @4Ω 5W, <0.000075% @8Ω 5W |
| THD @20-20kHz (90kBW) | <0.0005% @4Ω 5W, <0.0004% @8Ω 5W |
| SNR (A-wt) | 145dB |
| Dynamic Range @1kHz (A-wt) | 145dB |
| Frequency Response | 20Hz-40kHz (±0.2dB), 20Hz-100kHz (±0.4dB) |
| Output Level | 80Vpp @4Ω, 110Vpp @8Ω |
| AP Measured Noise Level (A-wt) | <2.3uVrms @G=L, <3.9uVrms @G=H |
| Input Sensitivity | 12.5Vrms @G=L, 3.9Vrms @G=H |
| Gain | 11.6dB @G=L, 22.0dB @G=H |
| Output Impedance | <5mΩ |
| Input Impedance | 10KΩ |
| Output Power | 200W @4Ω THD+N<1%, 240W @8Ω THD+N<10%, 200W @8Ω THD+N<1% |
| Adapter Impedance | ≥4Ω |
Note: The above data is the result of testing under the condition of AC220V 50Hz in TOPPING's laboratory.
Performance Graphs
For detailed visual representations of the amplifier's performance, including Signal to Noise Ratio (SNR), Dynamic Range, Frequency Response, Total Harmonic Distortion (THD), and Multitone FFT Spectrum, please refer to pages 20-31 of the official TOPPING B200 User Manual (PDF).
9. User Tips
Based on user experiences and common inquiries, here are some tips to optimize your TOPPING B200 amplifier:
- Mono Operation: The B200 is a single-channel (mono) amplifier. For stereo sound, you will need two B200 units.
- System Matching: Pair the B200 with a high-quality preamplifier and Digital-to-Analog Converter (DAC) to fully realize its potential for a detailed and clear sound.
- Gain Settings: Experiment with the High (H) and Low (L) gain settings to find the optimal match for your speakers and listening preferences. This can help achieve a balanced sound without unwanted distortion.
- Sound Character: Users often describe the B200 as having an exceptionally "quiet and black" background, allowing the source signal to shine through with micro-fine attack and decay, even at low volumes. This contributes to a precise and wide soundstage.
- Neutrality: The amplifier is praised for its neutrality, making it suitable for critical listening and mastering applications where an uncolored sound is desired.
- Fine-tuning: While neutral, some users find that subtle equalization (EQ) adjustments can further refine the sound to achieve a preferred blend of punch, warmth, detail, and clarity.
10. Warranty and Support
TOPPING accepts no liability for any loss or damage arising directly or indirectly from the failure of the B200 if the case has been opened or unauthorized modifications have been made. Please ensure all maintenance and repairs are performed by authorized personnel.
For detailed warranty information and terms of service, please refer to the official TOPPING documentation or contact customer support.
For technical support or inquiries, please contact: service@tpdz.net.
A PDF version of this user manual, containing all diagrams and performance graphs, is available for download: TOPPING B200 User Manual (PDF).