TOPPING B100

Contents

TOPPING B100 Single Channel Pure Rear Stage Amplifier User Manual

Model: B100 (TP312)

1. Introduction

This manual provides detailed instructions for the setup, operation, and troubleshooting of your TOPPING B100 Single Channel Pure Rear Stage Amplifier. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage.

For a complete reference, the official user manual is available in PDF format: View User Manual (PDF)

2. Package Contents

Verify that all items are present in the package:

  • B100 Main Unit x 1
  • AC to DC Power Adapter x 1
  • AC Cable x 1
  • Product Information Card x 1
  • 12V Trigger Cable x 1
TOPPING B100 Amplifier
Front view of the TOPPING B100 Single Channel Pure Rear Stage Amplifier.

3. Product Overview

3.1 Front Panel

The front panel features essential controls and indicators:

  1. Power Indicator: Illuminates when the unit is powered on.
  2. Power Switch: Touch to turn on the unit. Touch and hold to enter standby state.
Front Panel of B100 Amplifier
Diagram of the B100 amplifier's front panel, showing the power button and indicator.

3.2 Rear Panel

The rear panel provides all input, output, and power connections:

  1. Balanced Combo Input (XLR + 6.35mm TRS): For balanced audio input.
  2. Input Switch: Selects between balanced (left position) and single-ended (right position) inputs.
  3. Single-ended Input (RCA): For single-ended audio input.
  4. + Speaker Output (4mm jack): Positive terminal for speaker connection.
  5. - Speaker Output (4mm jack): Negative terminal for speaker connection.
  6. Gain Setting: Adjusts the amplifier's gain (H: High, M: Medium, L: Low).
  7. Firmware Upgrade Interface (USB-C FW port): For firmware upgrades only.
  8. 12V Trigger In (3.5mm jack): Allows external devices with 12V Trigger out to control the B100's power on/standby state.
  9. Power Input (DC38V): Connects to the provided power adapter.
Rear Panel of B100 Amplifier
Diagram of the B100 amplifier's rear panel, detailing all input, output, and control ports.

Note: Description of female XLR + 6.35mm TRS combo connector pin definition: 1.GND, 2.+, 3.- for XLR; GND, + for TRS.

4. Setup and Connections

4.1 Connecting the Input Source

Use TRS, XLR, or RCA cables to connect your audio source (e.g., DAC) to the B100. Ensure the input switch on the rear panel is set to the corresponding position (left for balanced input, right for single-ended input).

Input Source Connection Diagram
Illustration of connecting a DAC to the B100's input ports using various cable types.

4.2 Connecting Passive Speakers

Connect your passive speakers to the B100's speaker terminals. Ensure correct polarity (positive to positive, negative to negative).

Output Wiring Methods:

  • Direct Insertion (Banana Plug):
    1. Tighten the crystal case clockwise.
    2. Insert the banana plug into the end of the corresponding terminal.
  • Bare Wire / Y-insertion:
    1. Unscrew the crystal case counter-clockwise.
    2. Insert stripped metal speaker wires into the round holes in the copper posts or insert Y-terminals around the periphery of the posts.
    3. Important: Do not let bare speaker wires touch each other or the metal enclosure of the unit. This can cause damage to the unit and speakers.
    4. Finally, tighten the crystal case.
Speaker Connection Diagram
Diagram illustrating how to connect passive speakers to the B100 using bare wire or banana plugs.

4.3 Connecting 12V Trigger

If you have a device with a 12V Trigger out jack, connect it to the B100's 12V Trigger In (3.5mm jack) using the provided cable. This allows the external device to control the B100's power on/standby state.

12V Trigger Connection Diagram
Diagram showing the connection of the 12V Trigger cable between two B100 units or an external device.

5. Operation

5.1 Power On/Off

To power on the B100, touch the power switch on the front panel. To enter standby mode, touch and hold the power switch.

5.2 Input Selection

Use the input switch on the rear panel to select between balanced (XLR/TRS) and single-ended (RCA) input sources. Ensure the switch position matches your connected input.

5.3 Gain Setting

The B100 offers three gain settings: High (H), Medium (M), and Low (L). Adjust the gain setting on the rear panel according to your source device's output level and your listening preferences.

6. Troubleshooting

6.1 Can't be turned on

  1. Check Power Adapter: Connect the power adapter to an outlet without connecting it to the B100. If the adapter's LED blinks or does not light up, the adapter may be defective.
  2. Check Power Connection: Ensure all power cables are securely connected.

6.2 No Sound

  1. Power Status: Verify the device is powered on, the power connection is correct, and the adapter indicator LED is on.
  2. Cable Connections: Ensure all audio cables are fully inserted and correctly connected to all devices.
  3. Input Source Selection: Confirm that the correct input source is selected on the B100's rear panel.
  4. Volume and Mute: Check the volume levels on all connected devices and ensure none are muted.

6.3 Fault Codes (LED Flashes)

The power indicator LED flashes A times, pauses for 1 second, then flashes B times, pauses for 2 seconds, and repeats the cycle.

  • A=2, B=2 (Firmware upgrade failed): Unplug the power cable, then plug in a USB-C cable to the FW port on the rear panel and attempt to re-upgrade the firmware.
  • A=2, B=3 (Incorrect firmware version): Unplug the power cable, then plug in a USB-C cable to the FW port on the rear panel and attempt to re-upgrade the firmware.
  • A=1, B=1 & A=1, B=2 (Negative and positive voltage abnormal):
    1. Check if the power connection is correct and if the adapter indicator LED is on.
    2. If the problem persists after rebooting the unit without input and output connections, the unit may be defective. Contact the store of purchase.
  • A=1, B=3 (Amplifier circuit outputs abnormal DC voltage): After changing the song, turning down the source volume, and turning down the gain of the unit, unplug and re-plug the power cable and reboot the unit. If the problem still persists after rebooting the unit without input and output connections, the unit may be defective. Contact the store of purchase.
  • A=1, B=4 (Over-temperature protection): The protection circuit has activated due to high internal temperature. Reboot the B100 after it cools down. Ensure the unit is placed in a well-ventilated area.
  • A=1, B=5 (Load impedance anomaly):
    1. Check for short-circuited outputs or excessively low load impedance.
    2. After changing the song, turning down the source volume, and turning down the gain, unplug and re-plug the power cable and reboot the unit. If the problem persists after rebooting the unit without input and output connections, the unit may be defective. Contact the store of purchase.
    3. Verify speaker cables are connected correctly and that no bare conductors are touching the metal enclosure.
    4. Ensure all connections follow the instructions in this manual.
    5. Check if speaker cables are defective; try different cables.
    6. Check if the speakers themselves are defective.

7. Specifications

The following specifications are based on testing conducted under AC220V 50Hz in TOPPING's laboratory. Specifications are subject to change without prior notice for product improvement.

ParameterBAL InputSE Input
THD+N @1kHz (A-wt)<0.00008% @4Ω 5W
<0.00008% @8Ω 5W
<0.00008% @4Ω 5W
<0.00008% @8Ω 5W
THD @20-20kHz (90kBW)<0.00007% @4Ω 5W
<0.00007% @8Ω 5W
<0.00007% @4Ω 5W
<0.00007% @8Ω 5W
SNR (A-wt)151dB149dB
Dynamic Range @1kHz (A-wt)151dB149dB
Frequency Response20Hz-40kHz (±0.1dB)
10Hz-100kHz (±0.5dB)
20Hz-40kHz (±0.1dB)
10Hz-100kHz (±0.5dB)
Output Level56Vpp @4Ω
66Vpp @8Ω
56Vpp @4Ω
66Vpp @8Ω
AP measured noise level (A-wt)<0.7uVrms @G=L
<1.2uVrms @G=M
<2.6uVrms @G=H
<0.9uVrms @G=L
<2.3uVrms @G=M
<6.2uVrms @G=H
Actual noise level* (A-wt)<0.3uVrms @G=L
<1.0uVrms @G=M
<2.4uVrms @G=H
<0.7uVrms @G=L
<2.2uVrms @G=M
<6.2uVrms @G=H
Input sensitivity26.6Vrms @G=L
8.6Vrms @G=M
3.0Vrms @G=H
13.3Vrms @G=L
4.3Vrms @G=M
1.5Vrms @G=H
Gain0dB @G=L
10.4dB @G=M
19.9dB @G=H
6dB @G=L
16.4dB @G=M
25.9dB @G=H
Output Impedance<5mΩ<5mΩ
Input Impedance20KΩ5KΩ
Output Power100W @4Ω THD+N<1%
83W @8Ω THD+N<10%
70W @8Ω THD+N<1%
100W @4Ω THD+N<1%
83W @8Ω THD+N<10%
70W @8Ω THD+N<1%
Load Impedance≥4Ω≥4Ω

*Note: The actual noise level is obtained by boosting the noise of B100 by 40dB using a low noise amplifier in front of the APx555B then dividing the measured noise by 100 times.

8. Maintenance and Precautions

  • The output jacks should not be grounded or short-circuited.
  • Do not expose the unit to hot, humid environments or strong impacts.
  • Opening the case instantly voids the warranty. Any repairs should be handled by professional service personnel.
  • This unit is intended for indoor use only.
  • TOPPING accepts no liability for any loss or damage arising directly or indirectly from the failure of the B100.

9. User Tips

Based on user feedback, the TOPPING B100 is noted for its excellent sound quality. No specific operational tips or common user-discovered functionalities were found in the provided reviews or Q&A.

10. Warranty and Support

For warranty information and technical support, please contact the official TOPPING Professional Audio Store or your authorized dealer. Please note that opening the case will void the warranty.

For further details and comprehensive information, refer to the full PDF user manual: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.