TOPPING A70Pro

Contents

TOPPING A70Pro Fully Balanced Headphone Amplifier

Model: A70Pro

User Manual

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your TOPPING A70Pro fully balanced headphone amplifier. Please read this manual thoroughly before using the device to ensure proper functionality and to maximize your audio experience.

2. Package Contents

Please check that all the following items are included in your package:

  • TOPPING A70Pro (x1)
  • Remote control (x1)
  • AC cable (x1)
  • 6.35 mm to 3.5 mm adaptor (x1)
  • User manual (x1)
  • Warranty card (x1)

The user manual can also be downloaded from the official TOPPING website: http://www.topping.audio/

TOPPING A70Pro headphone amplifier in silver and black finishes, stacked.
TOPPING A70Pro headphone amplifier in silver and black finishes, stacked.

3. Product Overview

Familiarize yourself with the front and rear panels of the A70Pro to understand its various controls and connection points.

Front and rear panel overview of the TOPPING A70Pro headphone amplifier, showing all inputs, outputs, and controls.
Front and rear panel overview of the TOPPING A70Pro headphone amplifier.

3.1 Front Panel

  1. Screen
  2. Remote control receiver
  3. Menu button: Touch to enter/exit the setup menu or return to the parent menu.
  4. Input channel switching button
  5. Home page switching/Exit the setup menu button
  6. 4-PIN-XLR headphone output jack
  7. 4.4mm balanced headphone output jack
  8. 6.35mm headphone output jack
  9. Volume knob & User-defined button: Rotate to adjust volume. Press for user-defined function (set in [Setup Menu-Advanced-Button]).

3.2 Rear Panel

  1. Extender input connector
  2. Right channel balanced XLR+6.35mm TRS combo input
  3. Left channel balanced XLR+6.35mm TRS combo input
  4. Left channel single-ended RCA input
  5. Right channel single-ended RCA input
  6. Left channel single-ended RCA preamp output
  7. Right channel single-ended RCA preamp output
  8. Right channel balanced XLR preamp output
  9. Left channel balanced XLR preamp output
  10. 12V Trigger In/Out: Allows the A70 Pro to be activated by other devices or to activate other devices via a 3.5mm AUX cable. The connected device must be equipped with a 12V Trigger In/Out to use this feature.
  11. Ground lift switch: The LIFT setting can break ground loops in multi-device systems. Keep at "GND" for best performance if no ground loop is present.
  12. Firmware upgrade port: For firmware upgrades only.
  13. Power input: AC 100-240V 50Hz/60Hz
  14. Power switch
Close-up of the rear panel of the TOPPING A70Pro, showing various audio input and output connections with cables attached.
Rear panel connections of the TOPPING A70Pro.

4. Setup

4.1 Connect to the Input Source

Use XLR or RCA cables to connect your Digital-to-Analog Converter (DAC) to the A70Pro. If you have more than two sources, you can purchase the optional Extender EXT90 for four additional inputs. Note that the A70Pro can only use one input at a time.

User setup showing a TOPPING A70Pro stacked with another audio device and headphones.
Example setup with input source and headphones.

4.2 Connect Headphones

The A70Pro offers three types of headphone jacks: XLR-4, 4.4mm, and 6.35mm. Connect your headphones to the appropriate jack on the front panel.

User setup showing a TOPPING A70Pro connected via an XLR cable to a headphone.
Connecting headphones to the A70Pro via XLR.

4.3 Connect to Amplifier or Active Speakers

Use XLR or RCA cables to connect the A70Pro to a power amplifier or active speakers. To prevent damage to your devices, ensure that the amplifier or active speakers are turned off before making connections to the A70Pro.

5. Operation

5.1 Power On & Off / Standby

  • Power On & Off: Press the power switch on the rear panel to turn the A70Pro on or off.
  • Standby: When the unit is working, press and hold the volume knob on the front panel to enter standby mode. Press it again to exit standby. Alternatively, use the standby button on the remote control.

5.2 Input Channel Switching

Touch the input channel switching button on the front panel or press the left/right arrow buttons on the remote control to cycle through inputs.

5.3 Output Settings

The A70Pro offers flexible output modes:

  1. Set the output mode: Press and hold the remote middle button to access [Setup menu-Output mode].
    • HPA: Only front panel headphone jacks have output.
    • PRE: Only the Line out connectors on the rear panel have output.
    • HPA+PRE: Both headphone jacks and line out connectors have output.
  2. Select output channel: Use the remote A/B button to access [Setup menu-HPA output] / [Setup menu-PRE output].
    • HPA output channel: Choose to open one or all of 4-PIN-XLR, 4.4mm, and 6.35mm.
    • PRE output channel: Choose to open one or both of RCA and XLR.

    Note: In HPA+PRE output mode, remote A and B buttons are invalid, and all output channels are open. Individual channel output cannot be selected.

5.4 Volume Setting

  • Mute: Press the mute button on the remote control to mute. Press again or adjust volume to exit mute.
  • Volume Adjustment: Turn the volume knob or press the + and - buttons on the remote control. Long pressing + or - will quickly change volume; exercise caution to protect your hearing.
  • Volume Memory: The A70Pro memorizes the last volume setting for each output configuration (HPA+PRE, HPA-ALL, PRE-ALL, 3.5mm, 4.4mm, 4-PIN-XLR, RCA, XLR).

7. Extender Instruction

The TOPPING Extender EXT90 (sold separately) can be connected to the A70Pro via an aviation connector cable. This adds four stereo input channels to the A70Pro, with other functions remaining unchanged.

7.1 Input Selection with Extender

Once the extender is successfully connected, you can select its inputs. EXT1 to EXT4 correspond to inputs "1" to "4" on the rear panel of the EXT90.

Note: Hot plugging the EXT90 will not damage the unit, but it is not recommended.

8. Troubleshooting

If you encounter any issues with your A70Pro, please refer to the table below for common problems and solutions. If the problem persists, contact customer support.

Phenomenon Cause Solution
A70 Pro did not power on Check the power supply
No sound Wrong input was selected Select the correct input
Wrong output was selected Refer to "Output settings" in this manual for correct usage
Incorrect cable connections / No signal from source Check and reconnect cables; Check upstream devices
Firmware Error or Unknown file Incorrect firmware version Unplug and re-plug power cable, then flash the correct firmware
No firmware Unplug and re-plug power cable, then flash the firmware again. Do not disconnect from computer during flashing.
Update failed Firmware upgrade failed Unplug and re-plug power cable, then flash the firmware again
PN Voltage ERR or P Voltage ERR Negative and positive voltage abnormal Do not connect A70 Pro to any other devices, unplug and re-plug power cable and reboot.
HP DC abnormal Amplifier circuit outputs abnormal DC voltage After changing song or turning down volume, unplug and re-plug power cable and reboot A70 Pro.

If you still have problems or questions, please contact service@tpdz.net.

9. Specifications

Attribute Value
Dimensions (WxHxD) 22.2cm x 17.6cm x 4.8cm (Including protruding parts)
Weight 1.27 Kg
Power input 100-240VAC 50Hz/60Hz
Gain L/H
Signal input 1 x BAL (Combo: XLR/6.35mm TRS)
1 x SE (RCA)
1 x EXT (For connection to extender EXT90)
Headphone Amplifier output 1 x 6.35mm headphone output jack
1 x 4-PIN-XLR headphone output jack
1 x 4.4mm headphone output jack
Line Out output 1 x BAL (XLR)
1 x SE (RCA)
Other connectors 12V Trigger In (3.5mm jack)
12V Trigger out (3.5mm jack)
Display 2-inch LCD
Body Material aluminum
Channels 2 (2.0)
Recommended Headphone Maximum Impedance 501 - 600 Ohm

10. Precautions

  • The output jacks shall not be grounded or short-circuited.
  • Do not keep the unit in a hot, humid environment or hit the unit strongly.
  • Opening the case instantly voids the warranty!
  • Indoor use only.
  • Topping accepts no liability for any loss or damage arising directly or indirectly from the failure of A70 Pro.
  • For improvement purposes, specifications are subject to changes without prior notice.

11. User Tips

  • The A70Pro delivers exceptional clarity, dynamics, and virtually zero noise across various impedance loads, making it suitable for a wide range of headphones.
  • Both balanced and single-ended outputs perform brilliantly, offering versatility for different headphone types and audio setups.
  • Consider pairing the A70Pro with a high-quality DAC for optimal sound performance.

12. Warranty and Support

The TOPPING A70Pro comes with a warranty as detailed in the included warranty card. For technical support, service, or any questions not covered in this manual, please contact TOPPING customer service at service@tpdz.net.

A comprehensive user manual in PDF format is available for download: TOPPING A70Pro User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.