Introduction
Thank you for choosing the GMAIPOP F410 4-Channel Dash Cam. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your device. Please read this manual thoroughly before using the product.

Figure 1: GMAIPOP F410 4-Channel Dash Cam Overview
1. Setup and Installation
1.1. Install Front Dash Cam
- Clean the Windshield: Ensure your car's windshield is clean and free of dust, particles, or grease.

Figure 2: Cleaning the windshield
- Prepare Suction Bracket: Insert the suction bracket into the dashcam. Make sure to move the protective film on the suction cup.

Figure 3: Inserting the suction bracket
- Attach Dashcam: Attach the dashcam with the suction mount to the cleaned windshield. Adjust the camera lens to point forward towards the center of the road. Ensure the suction is locked tightly to prevent the dashcam from dropping during video recording.
Video 1: Demonstrates unboxing and front dash cam installation on a windshield.
1.2. Install Car Charger
Connect the car charger to the camera's USB port and route the cable according to one of the wiring diagrams below. Use the original car charger to avoid fault or incompatibility.

Figure 4: Car Charger Wiring Method A

Figure 5: Car Charger Wiring Method B
1.3. Install Rear Camera
- Insert Rear Cam: Insert the rear camera into the dashcam body completely.

Figure 6: Inserting the rear camera
- Route Rear Camera Cable: Install the rear camera's cable according to the diagram below.
- Hide the cable into the top panel.
- Slightly loosen the side panel and insert the cable carefully, especially if airbags are present.
- Insert the cable along the door's rubber seal, continuing until you reach the trunk area.
- Loosen the trunk's panel and route the cable as per the red diagram.
- Optional: Connect the rear camera's red cable to the positive pole of the reversing light. This connection allows the reversing image to display automatically when the car is in reverse. If you don't need this feature, skip this step.

Figure 7: Rear camera wiring diagram (illustrative)
- Secure Rear Camera: Attach the 3M sticky tape to the rear camera's bracket and adjust the angle. Secure the rear camera in the middle and above the license plate frame.
- Connect Rear Camera Cable: Connect the rear camera to the wired cable. Align the two arrows for a proper connection.
Important Note: Ensure all connections are secure for optimal functionality.
2. Operating Instructions
2.1. Dashcam Buttons

Figure 8: Dashcam Button Layout
| No. | Button/Slot | Function |
|---|---|---|
| 1 | Reset hole | Reset the Dashcam. |
| 2 | Power button | Long-press for ~3s to turn ON/OFF. |
| 3 | OK button |
|
| 4 | Up button |
|
| 5 | Down button |
|
| 6 | Menu/Mode button |
|
| 7 | Power slot (USB-C) | Connect a USB cable or car charger. |
| 8 | Rear camera port | Connect a rear camera. |
| 9 | TF Card slot | Insert a micro-SD card to record and save videos. |
| 10 | Fill light | Fill lights for the right & left cameras, which turn on automatically when brightness is very low. |
2.2. Connecting to Wi-Fi and App
The dashcam supports smartphone wireless Wi-Fi connectivity for easy control and file management via the "Viidure" app.
Step 1: App Download and Installation
- Scan the QR code below to download the "Viidure" app.
- Install the app and launch it. Select "Viidure" from the menu.

iOS App

Android App
Step 2: Adding the Device
For iPhone:
- Go to your phone's Wi-Fi settings.
- Select the camera's Wi-Fi network (e.g., "F410-12dc0e").
- Enter the default Wi-Fi password: 12345678.
- Once connected, open the "Viidure" app and complete the device addition.
For Android:
- Open the "Viidure" app.
- Tap "Add Camera" and follow the on-screen guide.
- In your phone's Wi-Fi settings, select the camera's Wi-Fi network and enter the default password: 12345678.
- After connecting, return to the app to complete the device setup.
Video 2: Demonstrates connecting the dash cam to a smartphone via Wi-Fi and using the app.
2.3. App Interface Overview (Viidure App)
The "Viidure" app provides comprehensive control and management features for your dashcam.
Camera Section:
- Manage your Dashcam devices.
- Add, view, or delete devices.
- Enter the video preview mode to see live footage.
Photo Album Section:
- Access and manage pictures or videos downloaded from the Dashcam.
More Section:
- Adjust app settings such as language preferences.
- Provide feedback or access additional information about the app.
2.4. Dashcam Functions via App
- Taking Photos: Control the Dashcam to capture photos, which are saved directly to the device.
- Video Playback and Full Screen: Switch between full-screen video and a zoomed-out view for playback.
- Camera Files: Access the Dashcam's file list, organized into categories:
- Loop Recordings
- Photo Files
- Emergency Events
- Parking Monitoring
- Camera Settings: Adjust settings like recording resolution and microphone controls.
2.5. Downloading and Playing Files
File Download:
- Navigate to Camera Files in the app.
- Select desired photos or videos.
- Tap Download to save them to your phone, where they can be viewed in the Photo Album.
2.6. Managing Photo Albums
Access the Photo Album within the app to organize and manage downloaded media:
- Files are arranged by date.
- Use the Select option to perform batch operations.
- Categories include Videos, Pictures, and Emergency Documents.
2.7. Video Playback Options
Browse videos at varying speeds, from slow motion (e.g., 1 frame per second) to fast-forward (e.g., 10x speed).
2.8. Document Editing
Use the app's editing features to enhance your media:
- Images: Crop, apply filters, and beautify.
- Videos: Clip segments, add music, and perform other customization.
2.9. Playback on Dashcam or PC
Method 1: Playback on the PC
Take out the micro-SD card from the dashcam and insert it into a card reader connected to your PC. You can then view and manage the video files.
Method 2: Playback on the Dashcam
- Stop any ongoing recording.
- Short-press the MENU button to enter Playback Mode.

Figure 9: Playback Mode Interface
- Use the UP and DOWN buttons to scroll through files.
- Long-press the MENU button to delete or protect the current file.
- Short-press the MENU button again to exit Playback Mode.
3. Maintenance
- Cleaning: Regularly clean the camera lenses and screen with a soft, dry cloth to ensure clear recordings. Avoid using harsh chemicals.
- Temperature: Operate the dashcam within the specified working temperature range (-20℃ to 65℃) to prevent damage.
- Firmware Updates: Check the "Viidure" app or manufacturer's website periodically for firmware updates to improve performance and add new features.
- SD Card Care: Format the micro-SD card regularly (e.g., once a month) to maintain optimal recording performance and prevent data corruption. Use a Class 10 or higher speed card.
4. Troubleshooting
- Dashcam not turning on:
Ensure the car charger is properly connected and the vehicle's power outlet is functional. Long-press the Power button for 3 seconds. If using a hardwire kit, verify correct installation.
- Poor image quality (blurry/unclear):
Clean the camera lenses and windshield. Ensure the protective film has been removed from the lenses. Check the recording resolution settings in the menu or app. Note that some users report the front camera can be blurry and not adjustable via the app.
- Wi-Fi connection issues:
Ensure Wi-Fi is enabled on the dashcam (if applicable, check settings). Verify the correct Wi-Fi network (F410-xxxx) and password (12345678). Some users report needing to manually connect to Wi-Fi and the app each time.
- Dashcam freezes or gets stuck:
Try resetting the dashcam using the reset hole (No. 1 in Figure 8). Ensure your micro-SD card is not corrupted; try formatting it or using a different, high-quality Class 10 card.
- Rear camera image is reversed (mirror image):
Check the dashcam settings for an option to flip or mirror the rear camera image. If not available, be aware that the image might be reversed, especially when used for accident reporting.
- Short battery life (parking mode):
The internal battery is designed for very short-term use (a few minutes) for emergency parking recording or safe shutdown. For extended parking monitoring, a hardwire kit is required for continuous power.
- No Polish language option:
The device may not support Polish language in its menu settings, as noted by some users.
5. Specifications
| Feature | Specification |
|---|---|
| Brand Name | GMAIPOP |
| Item Type | Car DVR (Portable Recorder) |
| Model | F410 |
| Number Of Lenses | 4 |
| Camera Resolution | 1920x1080 (FHD) |
| Pixels | 300Mega |
| View Angle | 170° |
| Aperture | F2.0 |
| Frames Per Second | 25 |
| Video Code | H.264 |
| Video Format | AVI, TS |
| Max External Memory | 128G |
| Memory Card Required Reading Speed | Class 10 |
| Interface | AV-In, Wi-Fi, Micro SD/TF |
| APP Compatibility | Framefox (Viidure) |
| Special Features | G-Sensor, Motion Detection, SD/MMC Card, With Rearview Mirror, Real Time Surveillance, Wi-Fi Function, Parking Monitor, NightShot Function, Loop-Cycle Recording Feature, Audio Recorded, Built-in Screen, Original Package |
| Display | IPS |
| Screen Ratio | 4:3 |
| Working Temperature | -20℃ - 65℃ |
| Power Source | Corded Electric |
| Battery Life | Need to be plugged in (Internal battery for short-term parking mode) |
| Battery Capacity (mAh) | 150mA |
| Is Batteries Included | Yes |
| OSD Language | Arabic, Chinese (Simplified), Chinese (Traditional), English, French, German, Japanese, Korean, Russian, Spanish |
| Weight | 0.5kg |
| Cable Length | 6m |
| Certification | CE, FCC |
6. User Tips
- SD Card Recommendation: Use a high-quality Class 10 micro-SD card for reliable recording. Some users have reported issues with certain brands (e.g., SanDisk Ultra 64GB), so consider a high-endurance card.
- Wi-Fi Connectivity: Be aware that Wi-Fi may need to be manually enabled and connected via the app each time you use it, as it might not auto-launch.
- Parking Mode: For continuous 24/7 parking monitoring, a hardwire kit is essential as the internal battery only provides a few minutes of power.
- Rear Camera Wiring: The red wire for the rear camera is optional for automatic reversing image display. The camera will still record when powered via the main unit.
- Language Support: Confirm available OSD languages before purchase if a specific language is critical, as some users noted the absence of Polish.
7. Warranty and Support
Warranty: This product comes with a 1-year warranty.
For technical support, troubleshooting assistance, or warranty claims, please contact the seller or refer to the official product page for contact information.
You can also refer to the User Manual (PDF) for additional information.