1. Introduction
This manual provides essential information regarding the LAUNCH X-PROG 3, including its features and usage instructions. The X-PROG 3 is a robust anti-theft solution, designed for professional repair shops and vehicle maintenance businesses. It offers advanced capabilities for vehicle key, engine, and gearbox programming, supporting multiple parts reprogramming across a wide range of vehicles.
This document is intended for vehicle owners and repair technicians. A basic understanding of vehicle systems is assumed.
2. Safety Information
Important: Please read this manual carefully and understand all safety precautions before operating this product.
2.1 Safety Grades
| Symbol | Definition | Usage |
|---|---|---|
| ! | Danger | Indicates a hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders. |
| ! | Warning | Indicates a hazardous situation which, if not avoided, could result in possible injury to the operator or to bystanders. |
| ! | Caution | Indicates a hazardous situation which, if not avoided, could result in serious equipment damage or property losses. |
2.2 Safety Precautions
- Never collide, throw, or puncture the test equipment. Avoid falling, extruding, and bending it.
- Do not insert foreign objects into or place heavy objects on your device. Sensitive internal components may be damaged.
- Do not use the test equipment in exceptionally cold or hot, dusty, damp, or dry environments.
- In areas where the test equipment might cause interference or generate a potential risk, turn it off.
- The test equipment is a sealed unit. There are no end-user serviceable parts inside. All internal repairs must be performed by an authorized repair facility or qualified technician.
- Never place the test equipment near apparatus with strong electromagnetic fields.
- Do not disconnect power abruptly when the test equipment is formatting or uploading/downloading, as this may cause program errors.
- Do not disconnect the battery or any wiring cables in the vehicle when the ignition switch is on, to avoid damage to sensors or the ECU.
- Disconnect the power supply to the ECU before performing any welding operations on the vehicle.
- Use extreme caution when performing operations near the ECU or sensors. Ground yourself when disassembling PROM to prevent damage from static electricity.
- When reconnecting the ECU harness connector, ensure it is firmly attached to prevent damage to electronic elements like ICs inside the ECU.
3. Product Overview
The LAUNCH X-PROG 3 is a versatile tool for advanced automotive diagnostics and programming. Below are the key components and their functions.
Figure 3.1: Front and back view of the X-PROG 3 device.
3.1 Device Components
| No. | Part Name | Description |
|---|---|---|
| 1 | DB26 diagnostic connector | To connect with all anti-theft cables. |
| 2 | Benz key slot | To place Benz car key. |
| 3 | Key slot | To place car key for RF detection. |
| 4 | Key chip slot | To place key chip. |
| 5 | Power indicator | Red light indicates faults. Orange light indicates normal function. |
| 6 | Valve | To tighten loose EEPROM board. |
| 7 | EEPROM slot | To insert EEPROM board. |
| 8 | Power port | For power charging. |
| 9 | DB15 diagnostic connector | To connect with main diagnostic cable. |
| 10 | DIY slot | To insert vehicle DIY board. |
4. Accessories
The X-PROG 3 comes with a variety of accessories to facilitate different programming tasks. The specific accessories may vary by region; please consult your local dealer or the packing list provided with your tool for exact details.
Figure 4.1: X-PROG 3 device and included accessories.
4.1 Packing List
- Main unit
- Power adaptor
- Main diagnostic cable
- Fourth-generation data acquisition cable
- Fourth-generation EEPROM data acquisition cable (without dismantling dashboard)
- BENCH mode cable
- MCU converter V1
- MCU converter V2
- MCU cable with multiple leads
- EEPROM chip adaptor
- Benz infrared analog acquisition key
- EEPROM converter
4.2 Accessory Descriptions
| Accessory Name | Description |
|---|---|
| Main Diagnostic Cable | Connects vehicle DLC port, VCI, and programmer for diagnosis. |
| Power Adaptor | Provides power supply for the programmer. |
| Fourth-generation data acquisition cable | Used after removing the vehicle dashboard; connects programmer, vehicle dashboard, and the cable. |
| Fourth-generation EEPROM data acquisition cable (without dismantling dashboard) | Connects programmer and vehicle dashboard, then place the probe (yellow lead) to the designated area. |
| BENCH mode cable | Connects programmer and engine to read engine or gearbox ECU. Refer to the BENCH mode diagram in the full PDF manual for specific connections. |
| MCU Converter V1 / V2 | Connects programmer with MCU (chip soldering is required). |
| EEPROM chip adaptor | Places the EEPROM chip onto the adaptor, then plugs it into the programmer socket. |
| Benz infrared analog acquisition key | Connects programmer with the key lock; insert the key into the programmer for further key operations. |
| EEPROM converter | Solder the desired chip on the EEPROM converter, then plug the board into the programmer (chip soldering is required). |
| MCU cable with multiple leads | Connects the programmer and MCU. |
5. Setup
Before performing any diagnostic or programming operations, ensure the X-PROG 3 is properly connected to your diagnostic tool and the vehicle.
5.1 Power Source
The X-PROG 3 does not have an independent power supply. It can be powered up via:
- The included power adaptor.
- Connecting the device through the vehicle's DLC (Data Link Connector).
5.2 Establish Hardware Connection
Turn off the vehicle ignition and locate the vehicle's Data Link Connector (DLC) to establish a hardware connection. Refer to the full PDF manual for detailed cable images and connection diagrams.
| User Scenario | End A Connection | End B Connection | End C Connection |
|---|---|---|---|
| Key programming (Main diagnostic cable) | Connect with Launch VCI connector for data transmission | Connect with vehicle's DLC | Connect with X-PROG 3 |
| Engine/Gearbox programming (Power cable) | Connect power supply | N/A | Connect with End B of the main diagnostic cable |
| Engine/Gearbox programming (MCU cable with multiple leads) | Connect with the engine or gearbox to be repaired/replaced | Connect with X-PROG 3 | N/A |
5.3 Establish Wireless Connection
Ensure your diagnostic tool is properly connected with X-PROG 3 wirelessly. It is strongly recommended to connect the diagnostic tool with the VCI connector using a USB cable for effective data transmission, but wireless connection is also possible:
- Slide down the status bar from the top of your diagnostic tool.
- Touch the settings icon, then navigate to Wireless and network > Bluetooth.
- Select the X-PROG 3 device to connect. Wait until the connection is successful.
6. Operating Instructions
The X-PROG 3 supports key programming, engine, and gearbox replacement functions. You can retrieve ECU information, read, erase, and write data for various chips.
6.1 Common Operations
Before using the programmer, enter the function interface:
- Turn on a Launch diagnostic tool and/or open the diagnostic App on the home screen.
- On the main diagnostic screen, select Anti-theft system from either Local Diagnose or Reset, then touch OK.
- You will then see a connection diagram. Touch OK to proceed.
- Depending on your requirement, select one of the following options: Gearbox Learning, Anti-Theft System, or Engine System.
6.2 Key Programming (Example: BMW)
This function allows you to backup old key data and write new data for new keys. The following procedure outlines key programming for BMW using a Launch diagnostic product.
- Backup Current Key Data:
- Touch Intelligent Mode.
- Touch OK to confirm the IMMO Type (e.g., CAS3/CAS3+).
- Touch Key Operation.
- Touch Key Learning.
- Touch OK after reading the onscreen instructions.
- Confirm the prompt to perform the function to generate a dealer key. Ensure the programmer is connected and the network is stable. Touch OK.
- Follow the instruction to take the key out from the ignition switch (if it's a smart key, place it outside the vehicle). Touch OK.
- Touch OK to save the key data.
- Enter the key file name and touch OK.
- Confirm that the key file is saved by touching OK.
- Generate a New Key:
- Touch the desired blank key position on the screen.
- Place the new key into the programmer key slot and touch OK.
- Confirm the key type. If you are using a smart key, touch YES.
- If the key generation is done, touch OK to confirm.
- If the newly generated key cannot start the vehicle, execute DME Synchronization or DLE Synchronization function as needed.
6.3 Gearbox Programming (Example: BMW)
This function allows you to restore old gearbox data or write new data after a gearbox replacement.
- Connecting the Gearbox:
- On the programmer function interface, touch EGS System to enter gearbox programming.
- Touch the correct chassis type (e.g., F Chassis 8HP, G Chassis 8HP).
- You will see a corresponding connection diagram. Touch OK. (Refer to the full PDF manual for visual connection diagrams.)
- Erasing Gearbox Data:
- Touch EGS Erasure.
- Touch DOWNLOAD to download necessary files.
- Touch OK after download completes.
- Confirm to proceed with the ECU Reset. Ensure supply voltage is not below 13V and is stable. Touch YES.
- Confirm if CAFD Code File is lost or current CAFS does not support backup. Touch YES to erase.
- Touch OK once EGS Erasure is successful.
6.4 Engine Programming (Example: Volkswagen)
This function supports engine data reading and writing backup data after an engine replacement. The procedure includes chip ID retrieval, engine connection, data backup, and data restoration.
- Retrieve Chip ID:
- Touch Engine on the programmer function interface.
- Select the appropriate Engine Brand.
- Touch Search for ECU model.
- Check the ECU model (usually printed on a sticker on the back of your engine). Enter the engine type in the dialogue box (e.g., MED17.7.7). Touch OK.
- Connect the Engine:
- Touch View Wiring Diagram.
- Read the connection diagram, perform the proper connection based on the engine type, and then touch OK. (Refer to the full PDF manual for visual connection diagrams.)
- Touch Read chip ID.
- When the Chip ID dialogue box appears, touch OK.
- Backup Data:
- Touch Backup EEPROM Data.
- Enter the file name for EEPROM data.
- Confirm the storage path and touch OK.
- Touch OK when data backup succeeds.
- Follow onscreen instructions to backup flash data as well.
- Restore EEPROM Data:
Caution: EEPROM restoration applies only when you have encountered irrevocable faults.
- Touch Restore EEPROM Data.
- Touch the desired Backup EEPROM file name.
- Confirm the selected Backup EEPROM file and touch OK.
- When the data is successfully restored, touch OK.
7. Technical Specifications
| Parameter | Value |
|---|---|
| Input voltage | 12 V DC |
| Input current | 500 mA |
| Working temperature | 0 to 50 °C |
| Storage temperature | -20 to 70 °C |
| Dimension (L x W x H) | 298 x 107 x 39 mm |
| Item Weight | 4.8 kg |
8. Maintenance
- Do not attempt to replace the internal rechargeable lithium battery. Contact your dealer for factory replacement.
- Use only the included battery and charger. Using an incorrect battery type carries a risk of explosion.
- Avoid abrupt power disconnection during formatting, uploading, or downloading processes to prevent program errors.
- Exercise extreme caution when working near the ECU or sensors. Ground yourself when disassembling PROM to prevent static electricity damage.
- Ensure ECU harness connectors are firmly attached when reconnecting to prevent damage to internal electronic components.
9. Troubleshooting
- Connection Issues: If the device experiences intermittent connection breaks, especially when moved, check all cables and connectors for secure and proper seating. A loose connection can be dangerous during critical programming operations.
- Program Errors: Abrupt power disconnection during software updates or data transfer can lead to program errors. Ensure a stable power supply and avoid interrupting the device during these operations.
- Device Not Responding: If the device is unresponsive, ensure it is properly powered. If using the vehicle's DLC for power, check the vehicle's battery and ignition status.
- Software Update Failure: If a software update fails, check your internet connection. If the network connection is unstable, try again.
- Compatibility: Ensure the X-PROG 3 is compatible with your specific Launch diagnostic tool model (e.g., X431 Pro5, X431 Pro Lite) before attempting operations. Refer to your diagnostic tool's documentation for compatibility details.
10. User Tips
- Secure Connections: Always double-check all cable connections before starting any programming task. Loose connections can interrupt critical processes and potentially damage vehicle components or the device.
- Stable Power: Ensure a stable power source for both the X-PROG 3 and the vehicle during programming. Fluctuations can lead to data corruption.
- Verify Compatibility: Before purchasing or attempting to use the X-PROG 3 with a specific Launch diagnostic tablet, confirm compatibility to ensure seamless operation.
- Refer to PDF Manual: For detailed visual guides, especially for complex wiring diagrams and specific connection instructions, always refer to the comprehensive PDF user manual available at this link.
11. Software Upgrade
Keeping your diagnostic software and application up-to-date ensures optimal performance and access to the latest features and vehicle coverage.
11.1 How to Update Diagnostic Software & App:
- On the main diagnostic screen of your Launch diagnostic tool, tap Software Update to enter the update center.
- Check the software you wish to upgrade from the list of available updates.
- Tap Update to begin the download and installation process.
- Once downloading completes, the software packages will be installed automatically.
Note:
- You may stop the process by tapping Stop, and tap Continue to resume the process later.
- In case of network connection failure, tap Retry.
12. Warranty and Support
12.1 Warranty Information
LAUNCH warrants this product against defects in workmanship and material for 1 year from the date of delivery. Final judgment of defects will be made by LAUNCH. The exclusive remedy for defective products is repair or replacement. LAUNCH is not liable for consequential or incidental damages.
Cases not covered by warranty include:
- Products with altered, removed, or defective mechanical serial numbers.
- Products exposed to extreme conditions (e.g., excessive temperature, moisture).
- Damage resulting from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper use of electrical sources.
- Products subject to accidents, mishandling, unauthorized alteration, abnormal usage or conditions, improper installation, repair, or storage.
12.2 Customer Service
If you have any questions regarding the operation of the unit, please contact your local dealer or LAUNCH TECH CO., LTD:
- Tel: +86-755-84557891
- E-mail: overseas.service@cnlaunch.com
Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Please include the quantity, part number, and item description with your order.