Introduction
This manual provides detailed instructions for the safe and efficient operation of your ETENWOLF ZEPHYR S3C Portable Air Compressor. Please read all instructions and safety warnings carefully before use to ensure proper functionality and to prevent electric shock, fire, or serious injury.
For questions or comments, contact ETENWOLF support at (1)877-838-0209 (Mon-Fri 8AM-5PM PST) or support@etenwolf.com.
Register your product at www.etenwolf.com to receive a 1-year extended warranty.
Package Contents
Ensure all items are present in the package:
- Zephyr S3C Air Compressor x 1
- Air Chuck x 1
- USB A to C Cable x 1
- User Manual x 1
- Pressure hose
- Presta valve adapter x 1
- Inflation needle x 1
- High-pressure tapered nozzle x 1
Product Overview
Familiarize yourself with the components and controls of your air compressor.
Component Identification:
- Unit button
- Light button
- "-" decrease pressure button
- Mode button
- Start/pause power button
- "+" increase pressure button
- Center display
- LED work light
- Pressure hose
- Type-C port (Input)
- USB-A port (Output)
- Presta valve adapter
- Inflation needle
- High-pressure tapered nozzle
- Manual mode icon
- Car mode icon
- Bicycle mode icon
- Ball mode icon
- Pressure unit indicator
- Target input value
- Actual pressure value
- Battery level indicator
- Safety alert symbol
Quick Start Guide
Follow these steps for quick inflation:
- Remove Pressure Hose: Remove the Pressure hose (09) from its storage channel.
- Connect Nozzle: Insert the nozzle (09) clockwise into the object being inflated.
- Activate Machine: Press the Start/pause power button (05) for two seconds to turn on the machine.
- Select Mode: Press the Mode button (04) to switch among the four different modes: Manual mode (15), Car mode (16), Bicycle mode (17), and Ball mode (18).
- Select Pressure Unit: Select the pressure unit (PSI, KPa, or Bar) by pressing the Unit button (01).
- Set Target Pressure: Press the "-" button (03) to decrease or the "+" button (06) to increase the target pressure value.
- Start Inflation: Press the Start/pause power button (05) again to start inflation.
- Automatic Stop: When the inflated item reaches the preset value, the unit will turn off automatically.
Note: A Presta valve adapter (12), an inflation needle (13), and a high-pressure tapered nozzle (14) are located on the back side storage panel.
Preset Pressure Values
The display shows the target input value (20) in smaller size at the top and the actual pressure value (21) in bigger size at the bottom.
| Mode | Adjustable Pressure Range | Default Pressure |
|---|---|---|
| Car mode | 8-130 PSI | 35 PSI |
| Bicycle mode | 10-145 PSI | 22 PSI |
| Ball mode | 3-16 PSI | 8.5 PSI |
| Manual mode | 3-160 PSI | 30 PSI |
Memory Function
The ETENWOLF inflator remembers your last target pressure value and unit option. You can change the default pressure at any time.
LED Work Light
The LED work light (08) is located at the front of the inflator.
- To turn on: First, power on the machine by pressing the Start/pause power button (05), then press the Light button (02).
- Light Modes: Switch between four different light modes: Bright flashlight, Ultra-bright flash light, Slow strobe light, and SOS light.
Note: The light will automatically turn off after 1 hour. After the first automatic turn-off, you can manually turn on the LED light for a second time. Once manually turned on for the second time, it will not automatically turn off and must be manually turned off.
Power Bank Function
The inflator can be used as a power bank to charge electronic devices such as phones, tablets, laptops, drones, and cameras. It provides USB-A Output 5V 2A, 10W.
Note:
- To function as a power bank, the inflator needs to be powered on.
- After 3 minutes of charging, the display panel will only indicate the battery level to save battery.
- After 2 minutes of fully charging the connected devices, the inflator will automatically turn off.
Battery Charging & Indicator
Charging with AC power supply
For optimal charging performance and stability, use a 5V 3A 15W PD charger to charge the built-in battery. Battery charging takes approximately 3.5 hours to fully charge from 0% to 100%. Using a 5V 2A 10W charger takes approximately 6 hours to fully charge from 0% to 100%.
The battery level indicator (22) is shown by four bars, with each bar representing 25% of capacity.
Note:
- After 2 minutes of inactivity after being fully charged, the inflator will automatically shut off.
- The inflator cannot be used while it is charging.
Pressure Recalibration
Different altitudes can cause variations in pressure readings (1-3 PSI). In high-altitude areas (especially over 5000 ft/1524 meters), you can recalibrate the pump's pressure sensor.
Recalibration Steps:
- Power on the pump (05).
- Hold the Light button (02) and Mode button (04) simultaneously for 10 seconds.
- When the entire screen flickers, recalibration is complete.
Note:
- Power off the pump before calibration.
- The Pressure hose (09) should not be connected to any item during recalibration. Any item providing pressure to the hose will disable the process.
- A charged battery or other power source is required for recalibration.
- There is no memory for new recalibration settings. Once the power is turned off, it will reset to sea level calibration (altitude 0 ft/meters).
Safety Instructions
- This product is not a toy and should not be used by children. Users should be above 16 years old. Keep a safe distance between children and the inflator while inflating.
- The product has a built-in lithium battery. Do not place the product into fire or dispose of the battery improperly.
- Overheating or water ingress may increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a risk of explosion.
- Store the product within temperatures ranging from -10°C to 60°C (-14°F to 140°F). Extremely hot or cold environments may damage the battery and shorten the inflator's lifetime. Long-term storage may decrease battery effectiveness. Charge the inflator at least once every three months to maintain performance.
- The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
- If there is an unusual noise or the temperature becomes very high during inflation, turn off the inflator immediately.
- Before setting the inflation pressure value, ensure the correct pressure unit is selected. Mixing up PSI and Bar could lead to dangerous overinflation.
- Unit conversion: 1 Bar = 14.5 PSI, 1 Bar = 100 KPa.
- Do not leave the pump unattended while it is in operation.
- Use the product in a dry and clean environment. Intrusion of sand and dust may cause damage. Do not wash the product with water.
- Use ETENWOLF's charger or other certified PD chargers and the included charging cable. Malfunction caused by actions not in accordance with these requirements is not covered by the warranty.
- To reduce the risk of electric shock, do not expose to rain. Store indoors.
Troubleshooting
| Problem | Solution |
|---|---|
| Slow inflation speed |
|
| Air compressor turns on, but does not inflate | Check whether the pressure of the item being inflated exceeds the preset pressure. |
| Unable to increase or decrease the preset pressure |
|
| The inflator inflates but the pressure shown on the display is zero. | If the air pressure is under 3 PSI, the displayed pressure will show zero due to the pump's minimum pressure range. |
| The battery level indicator does not show on the screen after charging. | Use a certified ETENWOLF charger or standard charger, and the included charging cable, and try to charge it. |
| There is an air leakage when connecting the high-pressure air hose. | Tighten the air nozzle. |
| Unable to charge other devices |
|
| Display shows the E08 error code | After shutting down and restarting, if the issue persists, send the device for factory repair. |
| Display shows the E10 error code | Motor malfunction warning. If the issue persists after shutting down and restarting, send the device for factory repair. |
| Display shows the E11 error code | Low-temperature charging protection. Restore temperature to above 0°C before continuing charging. |
| Display shows the E12 error code | High-temperature charging protection. Restore temperature to below 45°C before continuing charging. |
| Display shows the E13 error code | Low-temperature discharge protection. Restore temperature to above -20°C before continuing inflation or charging other devices. |
| Display shows the E14 error code | High-temperature discharge protection. Restore temperature to below 58°C before continuing inflation or charging other devices. |
| Display shows the E15 error code | Air pump exceeded working time. Check for leaks if warning persists after 30 seconds. |
| Display shows the E16 error code | Overpressure protection. Will return to normal after pressure release. |
| Display shows the E17 error code | High-pressure operation exceeded working time. Check if the inflated item is functioning abnormally if warning persists after 30 seconds. |
| Display shows the E18 error code | Battery damage warning. Device will shut down after 30 seconds. Send for factory repair. |
Specifications
| Name | Air Inflator |
|---|---|
| Model | Zephyr S3C Air Compressor |
| Dimensions | 134 x 171 x 96 mm (5.28 x 6.73 x 3.78 inches) |
| Inflation pressure range | 3-160 PSI / 0.2-11 Bar |
| Operating Temperature (Charging) | 0°C-45°C / 30°F-113°F |
| Operating Temperature (Discharging) | -20°C-70°C / -4°F-158°F |
| Storage temperature | -10°C-60°C / -14°F-140°F |
| High pressure air tube length | 0.9 meters |
| Battery capacity | 7800mAh for S3C |
| Working noise | Lower than 85dB within 1 meter |
| Input | Type-C: 5V 3A |
| Output | USB-A: 5V 2A |
| Charging time | 15W 3.5 hours / 10W 6 hours |
| Continuous working time | Approximately 25 minutes at a pressure range of 20-50 PSI, in a 25°C ambient temperature, under full charge |
| Sensor accuracy | ±1 PSI |
User Tips
- The compressor has sufficient battery capacity to inflate multiple tires on a single charge, even truck tires.
- For Presta valves on bicycles, first loosen the valve, then screw on the adapter to the Presta tube stem, and finally thread on the main Etenwolf hose. This makes inflation easier for difficult Presta valves.
- The device is noted for its robust build quality and faster inflation compared to other portable compressors.
- The ability to set pressure in 0.1 PSI increments allows for precise inflation.
- While the compressor is rugged and comes with many adapters, it does not include an integrated holder for the car tire connector. Keep track of all accessories to avoid misplacing them.
Warranty & Support
2-Year Coverage
Within two years of purchase, ETENWOLF provides timely and effective online after-sale service. They will repair or replace any defective product (due to manufacturing fault) within this warranty period.
Manufacturer Information:
Mozhen Technology (Shenzhen) Co., LTDCN-503, Floor 5, Building 4, Tianan Yungu Industrial Park
Phase II, Gangtou Community, Bantian Street, Longgang District, Shenzhen
Phone: (1)877-838-0209 (Mon-Fri 8AM-5PM PST)
Email: support@etenwolf.com
Website: www.etenwolf.com
Facebook: www.facebook.com/etenwolf
Made in P.R.C
Compliance: FC CE ROHS
For the full user manual in PDF format, please refer to the official document available at ETENWOLF Zephyr S3C User Manual (PDF).