WRWD CX-AD3G

Contents

WRWD Wireless CarPlay Android Auto Interface User Manual

Model: CX-AD3G

1. Introduction

The WRWD Wireless CarPlay Android Auto Interface (Model CX-AD3G) is designed to upgrade your original Audi car screen with modern CarPlay and Android Auto functionalities. This plug-and-play module integrates seamlessly with your vehicle's existing display and controls, offering enhanced navigation, communication, and entertainment options.

WRWD Wireless CarPlay & Android Auto Interface installed in an Audi dashboard

Figure 1: WRWD Wireless CarPlay & Android Auto Interface in an Audi A4/A5/S4/S5 dashboard.

Close-up view of the WRWD Wireless CarPlay Android Auto Interface module

Figure 2: The WRWD Wireless CarPlay Android Auto Interface module.

2. Specifications

2.1 General Specifications

FeatureSpecification
Operating Voltage9 - 16V
Operating Temperature-30 ~ +75°C
Stored Temperature-30 ~ +85°C
Environment Humidity≤98% (at 45°C), 65±5% (rated)
Power Consumption500mA (rated), 3A (Max)
Shutdown Current3 mA (Clock is on)
Quiescent CurrentLess than 3 mA
Charging Current≤2A (Host activates circuit protection if USB charging current > 1A, controls current below 1.5A)

2.2 Vehicle Compatibility

Audi ModelScreen SizeModel Years
A4/A5/Q5/S4/S56.5 inch2009 ~ 2011
A4/A5/S56.5 inch ~ 7 inch2012 ~ 2015
Q56.5 inch ~ 7 inch2012 ~ 2018
A6L/A78 inch2012 ~ 2015

3. Setup and Installation

3.1 Pre-installation Cautions

  • Always disconnect the CarPlay POWER before adjusting the DIP switches.
  • Ensure all connections are secure to prevent intermittent issues.
  • Antennas cannot be attached to hardware surfaces.

3.2 DIP Switch Configuration

The DIP switches must be set correctly according to your Audi model and screen size. Refer to the table below:

Switch 1Switch 2Switch 3Switch 4Switch 5Car ModelScreen Size
OFFOFFONOFFOFF12-15 A6/A7800*480 8"
ONOFFOFFOFFOFF12-18 Q5800*480 6.5"/7"
ONOFFONOFFOFF12-15 A4/A5/S4/S5800*480 6.5"/7"
OFFOFFOFFOFFON09-11 A4/A5/Q5/S4/S5400*240 5.8"

Note: For MMI systems with an INFO button, DIP switch 4 must be set to ON.

3.3 Connection Overview

The installation involves connecting the CX-AD3G module to various points in your vehicle's existing wiring harness and head unit. The main connections are:

  • Power Connections: Yellow (B+), Red (ACC), Black (GND), Blue (Camera power supply), Brown (Reserve detect).
  • Video Input/Output: Connect LVDS from the original head unit to the module. The module has inputs for REAR-CVBS (rear view camera), FRONT-CVBS (front view camera), and outputs AUX (audio output).
  • Audio: AUX audio output.
  • Data/Control: USB port (for phone, USB disk, software update), MIC (extra mic port), White and Black (360-RX).
  • Integration: Connect to the original vehicle head unit and the original air conditioning panel.

Important: Before entering the installation system, connect your phone to the original car's Bluetooth (for both call and media) and select the original car audio on the Bluetooth stereo interface. Alternatively, switch the original car sound channel to the AUX channel.

3.4 Reversing Camera Wiring

To integrate a reversing camera:

  1. Connect the camera's power supply to the module's camera power output.
  2. Connect the camera's video output (rear-CVBS/AHD720P, 25FPS/30FPS) to the module's REAR-CVBS input.

4. Operating Instructions

4.1 Core Functions

  • CarPlay/Android Auto: Supports both wireless and wired connections, providing access to navigation, music, calls, and voice assistants (Siri/Google Assistant).
  • Reversing Video Input: The module decodes video signals for rear-view and front-view cameras.

4.2 Car Control Integration

The interface utilizes your car's original controls for a seamless experience.

Audi steering wheel controls and MMI rotary knob

Figure 3: Original car controls (steering wheel and MMI rotary knob) used with the interface.

  • Steering Wheel Buttons: Use volume up/down buttons to adjust audio levels.
  • Central Control Knob:
    • Long press to switch between original car system and CarPlay/Android Auto interface.
    • Rotate the knob to move the cursor or scroll through menus.
    • Short press to confirm selections.
    • Long press to confirm activation of voice control (Siri/Google Assistant).
    • Short press up and down to navigate between songs/tracks.

4.3 Wireless CarPlay Connection

  1. On your iPhone, enable Wi-Fi and Bluetooth.
  2. On the car screen, navigate to
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.