Godox MS300, MS200

Contents

Godox MS300/MS200 Studio Flash Light User Manual

Compact Studio Flash with Built-in 2.4G Wireless X System

1. Introduction

The Godox MS Series Studio Flashes (MS200 and MS300) are lightweight, compact, and durable flash units designed for studio photography, portraiture, and still-life photography. These flashes can serve as a main light, background light, or fill light source, offering comprehensive functions and reliable performance.

Godox MS300 and MS200 Studio Flashes
Figure 1: Godox MS300 and MS200 Studio Flash Units

2. Safety Instructions

  • Always ensure the flash unit is powered off and unplugged before making any connections or adjustments.
  • Do not operate the flash in wet conditions or with wet hands.
  • Avoid direct eye exposure to the flash light, as it can cause temporary vision impairment.
  • The flash tube and modeling lamp can become very hot during operation. Allow them to cool before handling.
  • Use only the specified voltage (110V or 220V) for your unit. Check the label on the flash unit.
  • Keep the unit away from flammable materials.
  • Do not attempt to disassemble or repair the unit yourself. Refer to qualified service personnel.

3. Package Contents

Please check that all items are included in your package. If anything is missing or damaged, contact your retailer.

  • Godox MS200 or MS300 Studio Flash Unit
  • Power Cable
  • Modeling Lamp
  • Protective Lamp Cover
  • Standard Reflector (may be included depending on kit)
Godox MS200 without reflector, showing power cable and protective cap
Figure 2: Godox MS200 unit with power cable and protective cap (reflector not shown)

4. Product Overview

4.1 Front Panel and Flash Head

Front view of the flash head, showing the flash tube, modeling lamp, and Bowens mount
Figure 3: Front view of the flash head with flash tube, modeling lamp, and Bowens mount
  • Flash Tube: Provides the main flash illumination.
  • Modeling Lamp: A continuous light source to preview lighting effects.
  • Bowens Mount: Standard mount for attaching various light modifiers like reflectors, softboxes, and snoots.

4.2 Rear Control Panel

Rear control panel of the flash unit, showing LCD, buttons, and ports
Figure 4: Rear control panel with LCD display, function buttons, and ports
  • LCD Display: Shows current settings (power, channel, group, sync mode).
  • GR/CH Button: Group/Channel selection.
  • S1/S2 Button: Optical slave mode selection.
  • Buzzer Button: Toggles audible flash ready signal.
  • Modeling Lamp Button: Controls modeling lamp on/off and mode.
  • Test Button: Manually fires the flash.
  • SET Dial: Adjusts flash power output and navigates menus.
  • SYNC Port: For connecting a sync cord.
  • USB Port: For connecting Godox X1/XT16/XPro/X2 wireless receivers (optional).
  • Power Socket: For AC power cable.
  • Power Switch: Turns the unit on/off.

5. Setup

5.1 Mounting the Flash Unit

  1. Attach the flash unit to a standard light stand using the mounting bracket.
  2. Adjust the tilt angle of the flash head using the locking knob on the bracket.
Godox MS300 unit on a stand, side view
Figure 5: Godox MS300 mounted on a light stand

5.2 Connecting Power

  1. Ensure the power switch on the flash unit is in the OFF position.
  2. Connect the power cable to the power socket on the rear panel of the flash unit.
  3. Plug the other end of the power cable into a suitable AC power outlet (110V or 220V, matching your unit's specification).

5.3 Installing the Modeling Lamp

  1. Remove the protective lamp cover from the front of the flash unit.
  2. Carefully insert the modeling lamp into its socket. Do not force it.
  3. Replace the protective lamp cover when transporting or storing the unit.

5.4 Attaching Accessories (Bowens Mount)

  1. Align the accessory (e.g., reflector, softbox) with the Bowens mount on the front of the flash unit.
  2. Insert the accessory and rotate it clockwise until it locks into place.
  3. To remove, press the release button on the Bowens mount and rotate the accessory counter-clockwise.
Godox MS300 with a reflector attached, side view
Figure 6: Godox MS300 with a standard reflector attached

6. Operating Instructions

Godox MS300 with a reflector attached, rear view showing control panel
Figure 7: Godox MS300 with reflector, showing the control panel in operational context

6.1 Power On/Off

Flip the power switch on the rear panel to the 'ON' position to power on the flash. The LCD display will light up. Flip it to 'OFF' to power down.

6.2 Display Screen

The LCD screen displays the current flash power, wireless channel, group, and other status indicators. A clear and intuitive interface allows for easy monitoring of settings.

6.3 Flash Power Adjustment

Rotate the SET dial to adjust the flash power output. The power can be precisely set from 1/32 to 1/1 in 50 steps, allowing for fine control over light intensity.

6.4 Modeling Lamp Control

Press the Modeling Lamp button to cycle through its modes: ON, OFF, and Proportional (brightness adjusts with flash power). When ON, rotate the SET dial to adjust the modeling lamp brightness from 5% to 100%.

6.5 Wireless X System (2.4G)

The MS Series flashes feature a built-in Godox 2.4G wireless X system for remote control.

  • Setting Channels and Groups: Press the GR/CH button to switch between Group and Channel settings. Rotate the SET dial to select from 32 channels (1-32) and 16 groups (0-9, A-F). Ensure your trigger (e.g., Godox X1, XT16, XPro, X2) is set to the same channel and group.
  • Remote Control Functions: With a compatible Godox 2.4G wireless trigger, you can remotely control the flash power output, modeling lamp status, and buzzer function.

6.6 S1/S2 Slave Modes

Press the S1/S2 button to activate optical slave modes:

  • S1 Mode: The flash will fire in response to the first flash it detects from another flash unit. Suitable for manual flash systems.
  • S2 Mode: The flash will ignore the first pre-flash from a TTL flash and fire in response to the second (main) flash. Useful for cameras that emit a pre-flash.

6.7 Anti-Preflash Function

The anti-preflash function ensures synchronization with cameras capable of firing a pre-flash, preventing premature triggering.

6.8 Memory Function

The flash unit remembers the current parameters after 3 seconds of setting completion. Operation data will be restored to the original settings upon restart, ensuring consistent workflow.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the flash unit. For stubborn dirt, a slightly damp cloth can be used, followed by a dry one. Do not use solvents or abrasive cleaners.
  • Storage: Store the flash unit in a cool, dry place, away from direct sunlight and excessive humidity. Ensure the protective lamp cover is in place.
  • Modeling Lamp Replacement: If the modeling lamp burns out, ensure the unit is unplugged and cool. Carefully remove the old lamp and replace it with a new one of the same type and wattage.

8. Troubleshooting

  • Flash not firing: Check if the unit is powered on, properly connected to power, and if the test button works. Ensure the trigger is set to the correct channel/group and is within range. Check if the flash is in sleep mode (press any button to wake).
  • Inconsistent power output: Ensure the unit has fully recycled (buzzer sounds or ready light illuminates). Check power connections.
  • Wireless control issues: Verify that the flash and trigger are on the same channel and group. Check battery levels in the trigger. Ensure no strong interference sources are nearby.
  • Modeling lamp not working: Check if the lamp is properly installed and not burnt out. Ensure the modeling lamp function is enabled.

9. Specifications

FeatureGodox MS200Godox MS300
Max Power200Ws300Ws
Color Temperature5600K ±200K
Power Output Control1/32 to 1/1 (50 steps)
Modeling Lamp150W, adjustable 5%-100%
Wireless ControlGodox 2.4G X System (32 Channels, 16 Groups)
Sync ModeS1/S2 Optical Slave, Sync Cord
Dimensions (WxHxD)12.6cm x 16.7cm x 28.3cm
Weight2.6kg
Mount TypeBowens
Power SourceAC

10. User Tips

  • Quantity Check: Please note that these flash units are typically sold individually. If you require multiple units, ensure you select the correct quantity or purchase a specific kit that includes more than one flash.
  • Voltage Compatibility: Always confirm the voltage of the unit (110V or 220V) matches your local power supply before purchase and use to prevent damage.
  • Modeling Lamp Heat: The modeling lamp can get very hot. Be mindful of this when using softboxes or other modifiers that are close to the lamp, and allow adequate cooling time before packing away.

11. Warranty and Support

For warranty information, service, or technical support, please refer to the documentation provided with your purchase or contact your authorized Godox dealer. A detailed user manual in PDF format is also available for download from the product page: Godox MS Series User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.