1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Ezonetronics Wireless CarPlay Android Auto Upgrade Module. This module integrates Apple CarPlay and Android Auto functionalities into your Mercedes Benz NTG5.0 system, enhancing your driving experience with seamless smartphone connectivity.

Image: Ezonetronics Wireless CarPlay Android Auto Module
2. Package Contents
Please check the package for the following items:
- Main CarPlay/Android Auto Module
- Power Cable
- RCA/USB Cable
- LVDS Cable
- Wi-Fi Antenna
- CAN Gateway Cable
3. Specifications
| Parameter | Value |
|---|---|
| Operating Voltage | 9 - 16 V |
| Operating Temperature | -30 ~ +75°C |
| Stored Temperature | -30 ~ +85°C |
| Environment Humidity | ≤98% (at 45°C), 65±5% (rated) |
| Power Consumption | 500mA (rated), 3A (Max) |
| Shutdown Current | 3 mA (Clock is on) |
| Quiescent Current | Less than 3 mA |
| Charging Current | ≤2 A (when USB charging current > 1 A, host activates circuit protection to control current below 1.5 A) |
Compatibility
This module is compatible with Mercedes Benz vehicles from 2015 to 2018 equipped with the NTG 5.0 BT_VER system. Applied vehicle models include: A/B/C/E/S/V/CLA/CLS/GLA/GLC/GLE/GLS.
Supports Phone OS Systems: iOS & Android.
4. Installation Guide
4.1. Safety Precautions
- CAUTION: Never turn on the ignition with the Factory radio removed.
- Ensure the vehicle is turned off and the battery is disconnected before starting installation.
- If you are unsure about any step, seek professional installation.
4.2. Dip Switch Settings
The dip switches on the module must be set correctly according to your car model and screen size. Incorrect settings may result in display issues.
CAUTION: Please make sure CarPlay POWER is disconnected when adjusting the dip switches. Once the dip switches are set, then connect CarPlay POWER.
| Dip Switch 1 | Dip Switch 2 | Car Model |
|---|---|---|
| OFF | OFF | C/GLC/V/S |
| OFF | ON | A/B/E/CLA/CLS/GLA/GLE/GLS |
| Dip Switch 3 | Dip Switch 4 | Screen Size |
|---|---|---|
| OFF | ON | 800*480 (7.4"/8.4") |
| ON | OFF | 960*540 (8.4") |
| ON | ON | 1440*540 (12.3") |
4.3. Wiring Diagram & Connections
The module connects between the original car radio and the display. Follow the general connection points below:
- LVDS: Connect the original vehicle LVDS cable to the module's LVDS input, and then connect the module's LVDS output to the original display.
- Power: Connect the module's power cable to the vehicle's power harness.
- Yellow: B+ (Battery Positive)
- Red: ACC (Accessory Power)
- Black: GND (Ground)
- Blue: Camera Power Supply (for aftermarket camera)
- ANT: Connect the Wi-Fi antenna to the module. Ensure it is not attached to hardware surfaces for optimal signal.
- Rear Detect: Brown wire. Connect to the rearview light cable or 360 panoramic detection cable.
- 360 Panoramic Camera (if applicable):
- White: 360-TX (Connects to 360 panoramic universal box TXD)
- White and Black: 360-RX (Connects to 360 panoramic universal box RXD)
- REAR-CVBS: Connect to rearview camera or 360-degree panoramic AHD output.
- FRONT-CVBS: Connect to the front view camera.
- AUX: Audio output.
- USB: Connect mobile phone, USB flash drive, or for software upgrades.
Attention: When inserting cables to the host, please check if it is stuck properly. Move original car's tray to this way if needed.
4.4. Physical Installation Steps (General)
- Carefully remove the original car radio unit from the dashboard.
- Disconnect the original LVDS cable from the radio/display.
- Connect the module's LVDS input to the original LVDS cable from the car.
- Connect the module's LVDS output to the radio/display unit.
- Connect the module's power harness to the vehicle's power supply.
- Connect the Wi-Fi antenna to the module.
- Connect any optional cameras (front/rear) or USB devices as needed.
- Before fully reassembling, perform a preliminary test to ensure functionality.
- Carefully route all cables and secure the module in a suitable location behind the dashboard.
- Reinstall the original car radio unit and dashboard trim.
5. Operating Instructions
5.1. Function Statement
The module provides the following core functionalities:
- CarPlay/Android Auto: Integrates your iPhone or Android smartphone for navigation, music, calls, and other apps directly on your car's screen. Supports both wireless and wired connections.
- Reversing Video Input: The smart module can decode video signals, allowing for the integration of aftermarket rear-view cameras.

Image: Wireless CarPlay Smart Module Features Overview (Bluetooth, CarPlay, Android Auto, Factory Protocol, USB Play, Optional Camera, Lossless Installation, Voice Control, Live Map, Online Entertainment)
5.2. Using Steering Wheel and Central Control Buttons
The module utilizes your existing car controls:
- Steering Wheel Buttons:
- Long press to switch between original car system and CarPlay/Android Auto.
- Short press to connect/answer calls.
- Short press to hang up the phone.
- Short press to increase or decrease volume.
- Press to restart (specific button may vary).
- Central Control (Knob/Controller):
- Long press to switch systems.
- Knob movement navigates the cursor.
- Short press confirms selection.
- Move left/right to cut to the next song.
- Long press to activate voice control.
5.3. Wireless CarPlay Connection
- On your iPhone, open Wi-Fi and Bluetooth.
- On the car screen, navigate to the CarPlay settings within the module's interface.
- Select