1. Introduction
This manual provides essential information for the safe and effective installation, use, and maintenance of your Car Sun Shade Front Windshield Solar Window Tint Film. Please read all instructions carefully before proceeding with installation or use.
2. Safety & Warnings
Important Safety Information:
- Do not use this product for purposes other than its intended use as a car window sun shade and tint film.
- Inspect the product before each use; do not use if damaged.
- Follow all installation and operation guidelines to avoid injury.
- Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
3. Product Overview
The Car Sun Shade Front Windshield Solar Window Tint Film is designed to provide solar protection, heat insulation, and UV blocking for your vehicle's front windshield. Made from durable PVC material, this film also offers a color-changing aesthetic.
4. Package Contents
Upon opening the package, please verify that all components are present and undamaged:
- Car Sun Shade Front Windshield Solar Window Tint Film (in selected size and color)
- Instruction Card (this manual)
- (Optional, depending on kit): Squeegee, utility knife, spray bottle, cleaning cloth.
5. Setup and Installation
Proper installation is crucial for the performance and longevity of the film. It is recommended to perform installation in a clean, dust-free environment.
5.1 Preparation
- Remove all packaging materials and unroll the film carefully.
- Thoroughly clean the interior surface of your car's front windshield. Use a glass cleaner and a lint-free cloth to remove all dirt, dust, and grease. Scrape off any stubborn residue with a razor blade (use caution).
- Measure your windshield and cut the film to the appropriate size, leaving a small excess (approximately 1-2 inches) on all sides for trimming.
5.2 Application
- Prepare a spray solution of water with a few drops of mild soap in a spray bottle.
- Spray the interior surface of the windshield generously with the soap solution.
- Carefully peel off the clear liner from the adhesive side of the film. As you peel, spray the adhesive side of the film with the soap solution to prevent it from sticking to itself and to keep it lubricated.
- Position the film onto the wet windshield, adhesive side down. The soap solution will allow you to slide and reposition the film as needed.
- Once the film is in the desired position, spray the outer surface of the film with the soap solution.
- Using a squeegee, start from the center and work your way outwards, firmly pushing out all water and air bubbles from under the film. Overlap your strokes to ensure complete removal of water.
- Trim the excess film around the edges of the windshield using a sharp utility knife, leaving a small gap (approx. 1/8 inch) from the edge of the glass.
- Wipe away any excess water from the film and surrounding areas.
6. Operating Instructions
Once installed, the sun shade film operates passively. It provides continuous solar protection, heat insulation, and UV blocking. The color-changing properties of the film will be visible under different lighting conditions and viewing angles.
Allow several days for the film to fully cure. During this time, avoid rolling down windows or cleaning the film.
7. Maintenance
- Cleaning: After the film has fully cured (typically 3-5 days), clean it with a soft cloth and a non-ammonia based glass cleaner. Avoid abrasive cleaners or scrubbing pads that could scratch the film.
- Storage: If the film is removed or stored for any reason, ensure it is kept in a dry, cool place away from direct sunlight and moisture to prevent damage or degradation.
8. Troubleshooting
8.1 Common Issues and Solutions
- Bubbles after installation: Small water bubbles are normal and should disappear as the film dries and cures over several days. Larger air bubbles may need to be carefully pushed out with a squeegee or pricked with a fine needle and then smoothed.
- Film not sticking/peeling: Ensure the windshield surface was thoroughly cleaned and free of debris before application. Sufficient soap solution during application helps with adhesion. If peeling occurs, the film may need to be re-applied or replaced.
- Uneven tint/streaks: This can be caused by insufficient water removal during squeegeeing or uneven application of the soap solution. Re-wet the area and re-squeegee carefully.
9. Specifications
| Feature | Detail |
|---|---|
| Model Name | 202601425631257 |
| Item Type | Window Foils & Solar Protection |
| Window Foils Type | Front Window Solar Protection |
| Position | Front Windshield |
| Material | PVC |
| Transmittance | 60% - 80% |
| Heat Insulation Rate | 40% - 60% |
| Ultraviolet Blocking Rate | 80% - 100% |
| Item Weight | 0.03kg |
| External Testing Certification | CE |
| Origin | Mainland China |
10. User Tips
- Measure Carefully: Before purchasing, accurately measure your windshield to ensure you select the correct film dimensions. Some users have inquired about specific sizes like 20x250cm, so precise measurement is key.
- Patience is Key: Take your time during the application process, especially when cleaning the surface and squeegeeing out bubbles. Rushing can lead to a less-than-perfect finish.
11. Warranty & Support
For additional information, troubleshooting, or support, please refer to the official user manual PDF:
Manufacturer Information:
- Manufacturer: Shanghai Cifang Information Technology Co., Ltd
- Address: Room 8-106, No. 8 Wenshui Road, Jing'an District, Shanghai, China
- Contact: +86-18551929310, yanyuy2024@126.com
EU Authorized Representative:
- Representative: EC|REP Booyue International Trading GmbH
- Address: Wolfenbutteler Str.45 Magdeburg Germany
- Email: friedlicheur@hotmail.com
- Tel: +49 6994189028
This product is CE Certified.