1. Introduction
Thank you for purchasing the BaoFeng BF-1909 Walkie Talkie. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation of your device.
For a complete PDF version of this manual, please refer to the official documentation available from the seller.
2. Safety Warnings and Regulations
EU Regulatory Conformance
This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU, including 2006/66/EC, 2011/65/EU, and (EU)2015/863, 2012/19/EU. It can be operated under 2000m.
WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU. This information is applicable to EU countries only.
Compliance with RF Exposure Standards
The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
RF Exposure Compliance and Control Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany the device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions for RF Exposure:
- Transmit no more than 50% of the time. To transmit, press the Push-to-Talk (PTT) key. To receive, release the PTT key.
- Keep the radio unit at least 2.5cm away from the face. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness. Use of non-approved accessories may result in exposure levels exceeding FCC/controlled environmental RF exposure limits.
- Use only approved antennas, batteries, and accessories to avoid exceeding FCC RF exposure guidelines.
Precautions for Portable Terminals (Operating Prohibitions):
- Do not operate in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not operate near or in any blasting area.
- Do not operate near medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate in areas where wireless communication equipment is prohibited.
Important Tips for Product Use:
- Do not use unauthorized or damaged accessories.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Avoid prolonged high-volume reception.
- Do not place the product in the air bag deployment area in vehicles with airbags.
- Keep the product and its accessories out of reach of children and pets.
- Operate within the specified temperature range.
- Allow the product to cool if continuous transmission causes heat accumulation.
- Handle the product with care.
- Do not disassemble, modify, or repair the product and its accessories without authorization.
PMR446, FRS, GMRS, MURS Frequencies:
Note that there are restrictions on these bands (PMR446 in Europe, FRS, GMRS, MURS in the USA) that may make this transceiver illegal for use. Always ensure compliance with local regulations.
3. Package Contents
Please check the package contents upon receipt. If any item is missing, please contact your dealer.
- 1 x Radio Unit
- 1 x Li-ion Battery Pack
- 1 x Antenna
- 1 x Fast Desktop Charger
- 1 x Wall Adaptor
- 1 x Belt Clip
4. Product Features
BaoFeng BF-1909 Walkie Talkie highlighting 12W power, 4800mAh long standby, high power, 400-470MHz, and Type-C charging support.
- Frequency Range: FM radio 76-108 MHz; AM aviation frequency band: 108-136MHz (RX); VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX); UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX).
- High Power Output: 12W (10W-25W range).
- Battery: 4800mAh High Capacity Lithium-Ion battery.
- Charging: Type-C Charging and Base Charging.
- Long Range: 5km-10km maximum range, with silent penetration for better distance (up to 15KM intercom).
- Memory Channels: Up to 999 memory channels.
- Display: Large screen, full keyboard, no display (Is_Display: No).
- Waterproof: IP45 Water-Resistant.
- Privacy: Frequency hopping and scramble functions.
- Scanning: Channel scan, frequency scan, and three scan and recovery methods: TO, CO and SE.
- VOX Function: Voice Activated Transmit.
- Emergency Features: Alarm function, LED flashlight.
- Other Features: DTMF encoder and manual dial, programmable repeater offset, transmission time-out timer, end of transmission tone ("Roger Beep"), 10 levels of Squelch adjustment, two (2) pins for Kenwood accessory port.
BaoFeng BF-1909 Walkie Talkie demonstrating silent penetration and better distance, with 12W high power and 1-15KM intercom range.
BaoFeng BF-1909 Walkie Talkie showing a 5-10 KM call distance, suitable for construction or outdoor use.
5. Setup
5.1 Battery Information and Charging
The Li-ion battery pack is not charged at the factory. Please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times before regular use.
Diagram illustrating Type-C charging options for the walkie talkie: Car Charger, PC USB, Wall Charger, and Power Bank.
Two BaoFeng BF-1909 walkie talkies in their charging cradles, indicating charging status with red lights.
5.1.1 Charging the Battery Pack
- Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the charger. The indicator light will blink orange.
- Place the battery or radio into the charger. Ensure good contact with charging terminals. The indicator light will turn red, indicating charging has begun.
- A full charge takes approximately 2-5 hours. The lamp turns green when charging is complete.
- If charging the radio with the battery installed, ensure the radio is switched OFF for correct battery voltage detection and indicator operation.
5.1.2 Using the Type-C USB Charger
- Ensure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet or other compatible Type-C power source (e.g., power bank, PC USB).
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD (if applicable) will indicate charging.
Note: It is recommended to power OFF your radio while charging. If powered ON, you may not be able to transmit if the battery is completely empty. Allow the battery to charge to at least 1 bar before attempting to transmit. For optimal battery life, remove the radio from the charger within 6 hours and do not store it connected to the charger.
5.1.3 LED Indicator Status
| STATUS | LED |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble | Red blinks fast for a long time |
NOTE: Trouble indicates the battery is too warm, short-circuited, or the charger is short-circuited.
5.2 Installation of Accessories
5.2.1 Installing/Removing the Antenna
- Screw the antenna clockwise onto the antenna connector on top of the radio until it is firm.
- To remove, unscrew the antenna counter-clockwise.
5.2.2 Installing the Belt Clip
- Align the grooves of the belt clip with those on the radio and push down until you hear a click.
- To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide the clip upward and away.
5.2.3 Installing the Battery Pack
Before attaching or removing the battery, ensure the radio is turned off by rotating the power/volume knob counter-clockwise until it clicks.
- Align the battery parallel with the radio body, with the lower edge of the battery about 1-2cm below the radio's edge.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as it locks in place.
To Remove the Battery Pack: Press the battery release above the battery pack, then slide the battery downward.
5.2.4 Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.
5.3 Radio Overview: Buttons and Controls
Multiple views of the BaoFeng BF-1909 Walkie Talkie, showing its design and various buttons/controls.
The following diagram and list identify the main buttons and controls of your BF-1909 radio:
- Antenna
- LED Flashlight
- Status LED (Red for Transmitting, Green for Receiving)
- Power / Volume Knob
- Battery Release Latch
- PTT (Push to Talk) Button
- SK1-Programmable Key (Flashlight/Alarm Switch)
- SK2-Programmable Key (Radio/Monitor)
- Accessory Jack
- Type-C Charging Indicator
- V/M-VFO/MR Mode Key
- A / B Select Key
- SWEEP Key
- MENU Key
- Type-C Charging Port
- Color LCD (Note: Product specifications state 'No Display', this refers to a full alphanumeric display, a basic LCD for status may be present)
- Speaker
- Microphone
- EXIT Key
- Keypad
6. Operating Instructions
6.1 Basic Operations
6.1.1 Power On/Off and Volume Adjustment
- To turn ON: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, then display a frequency or channel.
- To turn OFF: Rotate the Volume/Power knob counter-clockwise until you hear a "click".
- To adjust volume: Rotate the Volume/Power knob clockwise to increase, counter-clockwise to decrease.
6.1.2 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between the upper (A) and lower (B) displays. The selected display becomes the active listening and transmit frequency/channel. Press and hold [A/B] to quickly switch between Double Wait/Signal Wait modes.
6.1.3 VFO/Channel Switch
Press the [V/M] key to switch between Frequency (VFO) mode and Channel (MR) mode.
- In Channel (MR) mode, the channel number is displayed.
- In Frequency (VFO) mode, 'VFO' is displayed.
- In MR mode, press and hold [V/M] to switch between frequency, channel, and name display modes.
6.1.4 Frequency (VFO) Mode
In VFO mode, use the ▲/▼ keys to increment or decrement the frequency according to the set frequency step. You can also input frequencies directly using the numeric keypad.
WARNING! Transmitting on unauthorized frequencies is illegal. Always ensure you have the proper license for the frequencies you operate on. Listening is generally permitted.
6.1.5 Channel (MR) Mode and Channel Selection
Channel (MR) mode is practical for everyday use with pre-programmed channels. Use the ▲/▼ keys or the encoder to navigate channels. Alternatively, input channel numbers directly using the keypad (e.g., [0][1][2] for channel 12).
6.1.6 Making a Call
Press the [A/B] key to select the main channel if two channels are displayed. In standby mode, press [V/M] to switch between VFO and MR mode.
- Channel Mode Call: Select a channel, hold down the [PTT] key, and speak into the microphone. The red LED will be on.
- Frequency Mode Call: Switch to frequency mode, input the desired frequency, hold down the [PTT] key, and speak into the microphone. The red LED will be on.
- Receive a Call: Release the [PTT] key. The green LED will be on when receiving a call.
NOTE: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.
6.1.7 Using the Flashlight
Press the [SK1] key once to turn on the high-intensity LED flashlight (Always On mode). Press [SK1] again for Strobe emergency mode. Press [SK1] a third time to turn it off.
6.1.8 Emergency Alert
Press and hold the [SK1] key for 3 seconds to activate the emergency alert. The radio will emit a loud siren and the flashlight will flash. Press [SK1] to exit. Use only in actual emergencies.
6.1.9 FM Radio
The radio can receive FM frequencies from 65-108MHz.
- In frequency or channel mode, press [SK2] to turn on the radio.
- Select the desired frequency with ▲/▼ keys or input directly. Press [#z] to automatically search for a station.
- Press [SK2] to exit FM radio.
Note: If a signal is received on the A/B receiving signal frequency/channel, the radio will temporarily switch to that frequency/channel for normal transmitting/receiving, then return to FM radio mode when the signal disappears.
6.1.10 Monitor Function
In standby, press and hold the [SK2] key to enter Monitor mode. This allows monitoring weak signals or carriers without signaling. Release [SK2] to return to standby. If no signal is present, it will emit noise.
6.1.11 Keypad Lock
The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the [*] key for about two seconds. You can also configure automatic keypad lock in the menu.
6.1.12 Frequency Reversal
A momentary press of the [R] key enables the reverse function, swapping transmit and receive frequencies. This is indicated by an 'R' on the LCD next to the +/- offset direction.
6.1.13 TX Repeaters Tone
Press [PTT] + [SK2] to send a 1750Hz repeater tone. This is useful for communications through repeaters. This function works even if the keypad is locked.
6.1.14 One Touch Frequency Search
- Press and hold the [SWEEP] key. The screen will display "SEARCH SWEEK...". The radio acts as a receiver.
- If a strong, stable signal is received, the frequency and any CTCSS/DCS values will be displayed.
- Press the [MENU] key to save the searched frequency and CTCSS/DCS to a channel.
Note: During frequency search, press the [#z] key to switch between UHF or VHF bands.
6.1.15 Weather Radio/Scan Weather Channel
The radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan 10 channels.
- To turn on NOAA Weather Scan, press the [OSQL] key for 3 seconds. The radio will enter Weather band mode.
- Press and hold the [#z] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Press and hold [#z] again to stop the scan.
- After stopping the scan, you can manually select weather channels using the ▲/▼ key.
- To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
6.2 Advanced Features (Menu System)
The radio's menu system allows customization of various settings. Each menu item has a numerical value for direct access.
6.2.1 Basic Menu Navigation
- Press the [MENU] key to enter the menu.
- Use the ▲/▼ keys to navigate between menu items.
- Press [MENU] again to select the desired menu item.
- Use the ▲/▼ keys to select the desired parameter.
- To confirm your selection, press [MENU]. To cancel changes, press [EXIT].
- To exit the menu at any time, press the [EXIT] key.
6.2.2 Using Menu Shortcuts
- Press the [MENU] key.
- Enter the two-digit number of the menu item using the numerical keypad.
- Press the [MENU] key to enter the item.
- Enter the desired parameter using ▲/▼ keys or numerical keypad.
- Confirm with [MENU] or cancel with [EXIT].
6.2.3 Scanning Modes
The radio features a built-in scanner for VHF and UHF bands. It scans in steps in VFO mode and channels in MR mode. To enable the scanner, press and hold the [#z] key for about two seconds. Press and hold [#z] again to exit scanning mode. Dual Watch is inhibited during scanning.
Setting Scanner Mode: (Menu 19)
- Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
- Carrier Operation (CO): Scanner stops on a signal, then resumes after the signal disappears.
- Search Operation (SE): Scanner stops on a signal and remains stopped. Press [#z] again to resume.
6.2.4 Scan CTCSS/DCS
These functions allow scanning for frequencies with CTCSS or DCS tones enabled. (Menu 16 for CTCSS, Menu 17 for DCS). They cannot be activated in Channel mode and will only start when the receiving band detects a signal.
6.2.5 Manual Programming (Channels Memory)
The radio features 999 memory channels. Each channel can store receive/transmit frequencies, transmit power, signaling information, bandwidth, ANI/PTT-ID settings, and a 6-character alphanumeric identifier.
Example: Programming a Channel Repeater Offset with CTCSS Tone
- Press [EXIT] to switch between menus.
- Press [V/M] to set the radio to VFO mode.
- Set TX encode tone: [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Example CTCSS 123.0).
- Enter RX frequency (e.g., 432.55000 MHz).
- Save RX frequency to channel (e.g., Channel 10): [MENU] [1][3] [MENU] [1][0] [MENU] [EXIT].
- Enter TX frequency (e.g., 437.55000 MHz).
- Save TX frequency to the same channel: [MENU] [1][3] [MENU] [1][0] [MENU] [EXIT].
- Press [V/M] to return to MR mode.
6.2.6 Repeaters Programming
This assumes you know your repeater's transmit and receive frequencies and are authorized to use it.
- Press [V/M] to set the radio to VFO mode.
- Enter the repeater's output (your receiving) frequency.
- Set frequency offset (Menu 12): [MENU] [1][2] [MENU] [offset value] [MENU].
- Set offset direction (Menu 11): [MENU] [1][1] [MENU] [+/-] [MENU].
- (Optional) Save to memory (see Manual Programming) and set CTCSS (see CTCSS section).
- Press [EXIT] to exit.
NOTE: If experiencing issues, check settings or contact your dealer/local amateur radio club. Some repeaters require a 1750Hz tone burst (press [PTT] + [SK2]).
6.2.7 VOX (Voice Activated Transmit)
This function allows hands-free communication. Speak into the microphone to activate transmission. (Menu 25 for VOX Switch, Menu 26 for VOX Level).
- VOX Switch: Enable/disable VOX.
- VOX Level: Adjust sensitivity (1-9, 9 being most sensitive).
NOTE: VOX is not enabled in Scan or FM Radio mode.
6.2.8 Dual Watch
This feature allows monitoring two channels simultaneously. The radio will switch to the channel with the most recent activity. (Menu 38)
Enabling/Disabling Dual Watch:
- Press [MENU].
- Enter 38.
- Press [MENU] to select.
- Use ▲/▼ keys to select Double Wait/Signal Wait/OFF.
- Press [MENU] to confirm.
- Press [EXIT] to exit.
6.2.9 Stopwatch Timer
In standby mode, press [MENU] + 57. The screen displays "STOP WATCH". Press [MENU] to start/restart counting. To exit, stop counting then press [EXIT].
6.2.10 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters. The numerical keys and [*], [#z] keys correspond to DTMF codes. [MENU], ▲, ▼, and [EXIT] keys correspond to A, B, C, and D codes respectively. To send DTMF codes, press the corresponding key(s) while holding down the [PTT] key. This works even with keypad lock enabled.
6.2.11 Customization (Menu Settings)
The radio allows customization of visual and audible features:
- Display Backlight (ABR) - Menu 51: Adjust backlight duration (ON/5sec/10sec/15sec/20sec).
- Beep Prompt (BEEP) - Menu 32: Enable/disable key press beep tone.
- Voice Function (VOICE) - Menu 30: Enable/disable voice prompts.
- Language (LANGUAGE) - Menu 29: Set menu language (English/Chinese).
- Working Mode (MDF-A) - Menu 39: Select display mode (Frequency, Channel, Name).
- Roger Beep (ROGER) - Menu 33: Enable/disable end-of-transmission tone.
- Power On Message (POWER ON MSG) - Menu 40: Customize welcome message (Voltage, Message, Logo).
- Power On Password (Power On PWD) - Menu 37: Enable/disable power-on password (default: 000000).
6.2.12 Reset - Menu 56
Two reset modes are available:
- Reset VFO: Resets all settings except channels to default.
- Reset ALL: Resets all settings, including channels, to default.
To perform a reset: Press [MENU] + 56, select VFO or ALL using ▲/▼, then press [MENU] to confirm. The radio will reboot.
7. Maintenance
7.1 Battery Maintenance Instructions
To ensure normal operation and prolong battery life:
- Regularly clean the charging connector with a clean, dry cloth to prevent dust accumulation.
- Charge the battery between 5°C and 40°C (40°F and 105°F). Charging outside this range may reduce battery life or cause leakage.
- Turn off the radio when charging a battery attached to the product to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging until the green light is on.
- Do not recharge a fully charged battery; this can shorten its life or cause damage.
- Do not charge a damp battery or radio; dry it thoroughly first.
7.2 Battery Charging Prohibitions
- Do not charge or replace the battery in locations with fuels, chemicals, explosive, or flammable materials.
- Do not charge a wet, deformed, leaking, or overheated battery.
- Do not charge with an unauthorized charger.
- Do not charge in locations with strong radiation.
- Avoid overcharging, as it shortens battery life.
7.3 Battery Storage and Transportation
- If storing the battery, keep it approximately 80% discharged.
- Store in a low-temperature, dry environment, away from hot places and direct sunlight.
- Do not short-circuit battery terminals.
- Never attempt to remove the casing from the battery pack.
- Do not store the battery in unsafe surroundings or throw it into fire.
- Damaged batteries must not be transported.
- When transporting two or more batteries, separate them from metal parts and each other to avoid short circuits.
- The radio must be switched off and secured against accidental activation if the battery is attached during transport.
8. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio. | Battery improperly installed, battery power low, or dirty/damaged battery contacts. | Remove/reattach battery, recharge/replace battery, clean/replace battery contacts. |
| Weak or intermittent voice during reception. | Battery voltage low, volume level low, loose/incorrectly installed antenna, blocked speaker. | Recharge/replace battery, increase volume, turn off radio and reattach antenna, clean speaker surface. |
| Cannot communicate with other group members. | Inconsistent frequency/signaling type, too far from other members. | Verify TX/RX frequency and signaling type, move towards other members. |
| Hear unknown voices or noise. | Radios using same frequency, radio in analog mode with no signaling. | Change frequency/squelch level, request dealer to set signaling for current channel. |
| Unable to hear due to too much noise/hiss. | Too far from other members, unfavorable position (blocked by buildings/underground), external disturbance. | Move towards other members, move to open/flat area and restart, stay away from interfering equipment. |
| Radio keeps transmitting. | VOX turned on, headset not installed correctly. | Turn off VOX function, check headset installation. |
NOTE: If the above solutions do not resolve your issues, please contact your dealer for technical support.
9. Specifications
| Feature | Specification |
|---|---|
| Frequency Band | FM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx) |
| Memory Channels | 999 |
| Power Supply | Li-Ion battery 7.4V/1400 mAh (BL-K6) |
| Operating Temperature | -10°C to +45°C |
| Working Mode | Monoband/Dualband |
| Modulation | F3E(FM) |
| Max. Frequency Deviation | ≤ ±5KHz |
| Spurious Radiation | < -60dB |
| Frequency Stability | ±2.5 ppm |
| Rx Sensitivity | < 0.2uV |
| Audio Output Power | ≥ 500mW |
| Dimensions | 64x121x35mm (LxAxP) |
| Weight | 240g |
| Output Power(w) | 10w-25w |
| Battery Capacity(mAh) | 4800mAh |
| Waterproof / Water-Resistant | IP45 |
| Battery Included | Yes |
| Material | ABS+PC |
| Storage Channel | 16 |
| Walkie Talkie Type | Portable |
| Is_Display | No |
Specifications are subject to change without notice.
WARNING: A direct plug-in AC/DC power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
10. User Tips
- Audio Clarity: Users report excellent clarity when transmitting, ensuring clear communication.
- Range Performance: The radio offers good range, with reported distances of 5-10 km and up to 15 km intercom range, confirming its high power output.
- Battery Life: The 4800mAh battery provides long standby time. Ensure proper charging and maintenance to maximize battery lifespan.
- Charging Convenience: The inclusion of Type-C charging makes it versatile for charging from various sources like power banks, PCs, or car chargers.
- Programming: When programming the radio, it's recommended to read the factory software data first, then rewrite with your desired frequencies to avoid errors.
11. Support
If you encounter any problems that cannot be resolved using this manual or have further queries, please contact your dealer for technical support.