GELID GP-Ultimate

Contents

GELID GP-Ultimate Thermal Pad Instruction Manual

High Performance Thermal Interface Material for CPU, GPU, and other Electronic Components

1. Introduction

The GELID GP-Ultimate is a high-performance thermal pad designed to provide superior heat conductivity for various electronic components. It is ideal for use with CPUs, GPUs, memory modules, chipsets, and other heat-generating components in computers, LED lighting, military electronics, power supplies, telecom services, wireless instruments, and automotive control systems. This thermal pad is non-electrical conductive, non-corrosive, non-curing, non-toxic, and user-friendly, making it a safe and effective solution for thermal management.

GELID GP-Ultimate Thermal Pad packaging and product
Figure 1: GELID GP-Ultimate Thermal Pad product and packaging.

2. Safety Information

Please observe the following safety guidelines when handling and installing the GELID GP-Ultimate thermal pad:

  • Keep out of reach of children and pets.
  • Avoid direct contact with eyes. In case of contact, rinse thoroughly with water.
  • Do not ingest.
  • Handle with clean hands to prevent contamination and ensure optimal performance.
  • Store in a cool, dry place away from direct sunlight and extreme temperatures.

3. Package Contents

Each package contains:

  • GELID GP-Ultimate Thermal Pad (quantity and size as per your purchase)
  • Protective films on both sides of the thermal pad

Note: The brand has updated its packaging for GP-Ultimate. You may receive either the old or new packaging version, but the performance of the product remains unchanged.

Comparison of old and new GELID GP-Ultimate Thermal Pad packaging
Figure 2: Description of switching between new and old packaging versions.

4. Specifications

The GELID GP-Ultimate thermal pad offers the following key specifications:

Property Data
Thermal Conductivity 15 W/mK
Composition Silicone elastomer
Color Grey
Hardness (Shore) 60-70 Shore 00
Density 3.2 g/cm³
Temperature Range -40°C to +200°C
Breakdown Voltage (V/mm) >8000 V
Flame Rating UL 94 V-0
Dielectric Constant 12.6 MHz
Tensile Strength 32 psi
Volume Resistivity 0.68 x 1012 ohm-cm

Available Sizes (Length x Width): 90x50mm, 120x20mm, 120x120mm

Available Thicknesses: 0.5mm, 1.0mm, 1.5mm, 2.0mm, 2.5mm, 3.0mm

Back of GELID GP-Ultimate Thermal Pad packaging showing specifications
Figure 3: Product specifications as printed on the packaging.

5. Setup and Installation

Follow these steps to properly install your GELID GP-Ultimate thermal pad:

  1. Prepare the Surface: Ensure the surfaces of both the heat-generating component (e.g., CPU, GPU, memory chip) and the heatsink are clean, dry, and free from any dust, old thermal paste, or residue. Use isopropyl alcohol for cleaning if necessary.
  2. Measure and Cut: Carefully measure the area where the thermal pad will be applied. If the thermal pad is larger than needed, cut it precisely to the required size using sharp scissors or a utility knife.
  3. Remove Protective Film (Side 1): Gently peel off one of the protective films from one side of the thermal pad. Avoid touching the exposed thermal material with your fingers to prevent contamination.
  4. Apply to Component: Carefully place the exposed side of the thermal pad onto the surface of the component (e.g., GPU die, memory chip). Ensure it is centered and covers the entire surface that needs thermal transfer.
  5. Peeling protective film from a thermal pad
    Figure 4: Gently peeling off the protective film from the thermal pad.
  6. Remove Protective Film (Side 2): Once the thermal pad is securely in place on the component, carefully peel off the second protective film from the top side of the thermal pad.
  7. Thermal pad applied to an electronic component
    Figure 5: Thermal pad correctly applied to a component, ready for heatsink installation.
  8. Install Heatsink: Carefully align and install the heatsink or cooling solution over the thermal pad, ensuring even pressure is applied. Secure the heatsink according to its manufacturer's instructions.

6. Operation

The GELID GP-Ultimate thermal pad is a passive component designed to facilitate heat transfer. Once installed, it will continuously work to bridge microscopic gaps between your heat-generating component and its cooling solution, ensuring efficient thermal dissipation. No active operation or configuration is required after installation.

7. Maintenance

Thermal pads generally require minimal maintenance. However, for optimal performance and longevity of your components, consider the following:

  • Regular Cleaning: Periodically clean dust and debris from your heatsink and cooling fans to ensure unrestricted airflow.
  • Inspection: If you disassemble your cooling system, inspect the thermal pad for any signs of degradation, cracking, or drying. While GP-Ultimate is non-curing, extreme conditions or prolonged use might warrant inspection.
  • Replacement: It is recommended to replace thermal pads whenever the heatsink is removed from the component, as the pad may lose its optimal contact properties upon reapplication. Replace with a new GELID GP-Ultimate thermal pad of the correct size and thickness.

8. Troubleshooting

If you experience higher than expected temperatures or thermal throttling after installing the thermal pad, consider these troubleshooting steps:

  • Incorrect Thickness: Ensure you have selected the correct thickness for your application. A pad that is too thin may not make proper contact, while one that is too thick may prevent the heatsink from seating correctly.
  • Improper Application: Verify that the thermal pad was applied evenly and covered the entire surface of the component. Ensure no air bubbles were trapped during application.
  • Heatsink Mounting Pressure: Check that the heatsink is mounted with adequate and even pressure. Uneven pressure can lead to poor contact and reduced thermal transfer.
  • Contamination: Ensure that no dust, debris, or fingerprints contaminated the thermal pad or component surfaces during installation.
  • Component Compatibility: Confirm that the thermal pad is suitable for your specific component and cooling solution.

9. User Tips

  • The GELID GP-Ultimate thermal pads are known for being easy to apply and cut, allowing for precise fitting to various components.
  • Many users have reported significant temperature drops (e.g., 30 degrees Celsius) when replacing older or stock thermal pads with GP-Ultimate.
  • These pads are particularly effective for GDDR6 RAM and can help resolve graphics corruption issues caused by inadequate thermal management.
  • To verify the authenticity of your GELID product, use the QR code and the code on the back of the packaging on the official Gelid Solutions website.
  • When ordering multi-packs (e.g., "90x50 x2"), you will receive two individual pads of the specified dimensions (e.g., two 90x50mm pads), not a single pad that needs to be split.

10. Frequently Asked Questions (FAQ)

Q: What color are the GELID GP-Ultimate thermal pads?
A: The pads are typically a light grayish color.
Q: If I order a pack like "90x50 x2", does that mean I get one 90x50 pad that I need to cut into two, or two separate 90x50 pads?
A: You will receive two separate 90x50mm pads.
Q: Is this product original and authentic?
A: Yes, the product is authentic. You can verify its originality using the QR code and the code provided on the back of the packaging on the official Gelid Solutions website.

11. Warranty and Support

For detailed warranty information and technical support, please refer to the official GELID Solutions website or the documentation included with your product. A user manual in PDF format may also be available for download, providing additional guides and documents.

For further assistance, you may consult the comprehensive item guides and documents available from the manufacturer. A PDF version of the user manual can be found at: GELID GP-Ultimate User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.