Yinuogo YNG200

Contents

Yinuogo YNG200 Universal 433.92MHz Receiver Controller

User Instruction Manual

Introduction

The Yinuogo YNG200 is a versatile 433.92MHz receiver controller designed to enhance or replace existing garage door and gate automation systems. It supports a wide range of fixed, learning, and rolling code remote controls, offering a cost-effective solution for expanding your system's remote capacity or consolidating multiple remotes into one.

Package Contents

  • 1 x YNG200 Receiver Unit
  • 1 x External Antenna
  • 1 x English Instruction Manual
Contents of the YNG200 package: receiver unit, antenna, and English instruction manual.
Figure 1: YNG200 Package Contents

Specifications

FeatureSpecification
ModelYNG200
Frequency433.92MHz (433MHz)
Code CompatibilityFixed Code, Learning Code, Rolling Code
Channels2
Power Supply9V-24V AC/DC
Working Temperature-40℃ to +80℃
AntennaBuilt-in Aerial, Reception range 30m-100m
EU LVD VoltageBelow 50Vac or 75Vdc
CertificationCE
OriginMainland China
The YNG200 receiver supports Fixed Code, Rolling Code, and Learning Code 433.92MHz remote controls.
Figure 2: Code Compatibility

Setup and Installation

The YNG200 receiver can be integrated into various gate and garage door automation systems. It typically connects to your existing control board.

Wiring Diagram and Connections

Refer to the wiring diagram below for connecting the receiver to your system. Ensure power is disconnected from your main control board before making any connections.

Detailed wiring diagram for the YNG200 receiver showing ANT, CH1, CH2, U+, and GND terminals.
Figure 3: YNG200 Receiver Wiring Diagram
  • ANT: Connect the external antenna here for optimal reception.
  • CH1: Relay Output 1. Connect to the input of your gate/garage door opener for channel 1.
  • CH2: Relay Output 2. Connect to the input of your gate/garage door opener for channel 2.
  • U+: Positive power input (9V-24V AC/DC).
  • GND: Ground connection for power supply.

Typical Installation Scenarios

Diagram showing the receiver connecting to a motor and controller for gate automation.
Figure 4: Receiver Connection to Gate Motor/Controller
Scenarios for using the receiver: replacing an old 12V-24V 433MHz receiver or adding up to 100 new remote controls.
Figure 5: Replacing an Old Receiver or Adding New Remotes

The receiver can either replace an existing 12V-24V 433MHz receiver or be added in parallel to your current system to expand the number of compatible remote controls (up to 100).

Operating Instructions

Once the receiver is correctly wired and powered, and your remote controls are programmed, pressing a programmed button on your remote will activate the corresponding relay (CH1 or CH2) on the receiver. This action will trigger the connected gate or garage door opener.

Video 1: Demonstration of programming and operation of the YNG200 receiver.

Programming Remote Controls

The YNG200 receiver supports two programming modes: Pulse Mode (momentary) and Latch Mode (toggle).

1. Programming in Pulse Mode (Momentary Action)

In Pulse Mode, the relay activates only while the remote button is pressed.

  1. Ensure the YNG200 module is powered up. The Power LED will be ON.
  2. Press Button S1 once to program Relay 1, or Button S2 once to program Relay 2. The Learn LED will light up.
  3. Press and hold a button on your remote control. Continue holding until the Learn LED on the receiver flashes five times, then release the remote button.
  4. The remote button is now programmed in Pulse Mode for the selected relay.

2. Programming in Latch Mode (Toggle Action)

In Latch Mode, the relay activates with one press and deactivates with the next press of the same remote button.

  1. Ensure the YNG200 module is powered up. The Power LED will be ON.
  2. Press Button S1 twice to program Relay 1, or Button S2 twice to program Relay 2. The Learn LED will light up.
  3. Press and hold a button on your remote control. Continue holding until the Learn LED on the receiver flashes five times, then release the remote button.
  4. The remote button is now programmed in Latch Mode for the selected relay.

Note: Each button on your remote control can be programmed independently for either Pulse or Latch mode and assigned to either Relay 1 or Relay 2.

Resetting the Module (Erasing All Remote Controls)

To clear all programmed remote controls from the receiver's memory:

  1. Press and hold either Button S1 or Button S2 on the control module.
  2. Continue holding the button until the Learn LED lights off (it may flash before turning off).
  3. All remote controls previously stored in the module's memory will now be erased.

Maintenance

The YNG200 receiver is designed for low maintenance. To ensure optimal performance:

  • Keep the receiver unit clean and free from dust and debris.
  • Periodically check all wiring connections to ensure they are secure.
  • Ensure the antenna is positioned for best reception and is not obstructed.

Troubleshooting

ProblemPossible CauseSolution
Remote control does not activate the gate/garage door.
  • Receiver not powered.
  • Remote not programmed or incorrectly programmed.
  • Remote control battery is low or dead.
  • Wiring issue between receiver and opener.
  • Check power supply to the receiver (Power LED should be ON).
  • Re-program the remote control following the programming instructions.
  • Replace the battery in your remote control.
  • Verify all wiring connections are secure and correct.
Poor reception range.
  • Antenna not properly connected or positioned.
  • Interference from other devices.
  • Obstructions between remote and receiver.
  • Ensure the external antenna is securely connected and extended. Try repositioning it.
  • Move the receiver away from potential sources of interference.
  • Ensure a clear line of sight between the remote and the receiver.
Receiver does not learn remote codes.
  • Remote control is not 433.92MHz.
  • Incorrect programming steps followed.
  • Receiver memory is full (unlikely, but possible).
  • Verify your remote control operates at 433.92MHz.
  • Carefully follow the programming instructions step-by-step.
  • Try resetting the module to clear all memory, then re-program.

User Tips

  • Compatibility Check: Before installation, confirm that your existing remote controls or system operate at 433.92MHz. The YNG200 is known to work well with brands like BFT MITTO 2 TLC.
  • Expand Your System: This receiver is an excellent solution if your original receiver's memory is full, allowing you to add up to 100 additional remote controls.
  • Cost-Effective Solution: If you need many additional remotes, using the YNG200 can be significantly more economical than purchasing original brand remotes.
  • Consolidate Remotes: If you have multiple remotes for different systems, you can program them all to a single 4-channel remote compatible with the YNG200 for convenience.

Frequently Asked Questions (FAQ)

Q: Can this receiver work with a Top 44RBN remote control?
A: The YNG200 receiver is designed to work with 90% of 433.92MHz remote control brands on the market, supporting fixed, learning, and rolling codes. While specific compatibility with "Top 44RBN" cannot be guaranteed without testing, if your remote operates at 433.92MHz and uses one of the supported code types, it is likely to be compatible. Please refer to the list of compatible models in the product description for common brands.

Warranty and Support

This product typically comes with a 1-year warranty from the seller. For any technical assistance, troubleshooting beyond this manual, or warranty claims, please contact your point of purchase or the seller directly. Provide your product model (YNG200) and a detailed description of the issue for prompt support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.