CENTURY AOKE AK-YK68-02S

Contents

CENTURY AOKE AK-YK68-02S RF Wireless Remote Control Relay Switch User Manual

Model: AK-YK68-02S

1. Introduction

The CENTURY AOKE AK-YK68-02S is a versatile 1-channel RF wireless remote control relay switch designed for various applications such as controlling lights, lamps, garage doors, shutters, and projection screens. This manual provides detailed instructions for its installation, operation, and maintenance to ensure optimal performance and longevity of the device.

2. Features

  • High-quality wireless control for reliable operation.
  • Wireless signal can penetrate walls, floors, and doors, offering extended range.
  • Utilizes fixed coding for stable and reliable performance.
  • Enables remote activation or deactivation of the receiver from a significant distance.
  • Remote control features a slidable cover to prevent accidental presses.
  • Designed for easy installation and operation.
  • Integrated hook on the remote control for convenient portability.

3. Specifications

AttributeValue
Brand NameCENTURY AOKE
Model NumberAK-YK68-02S
Operating VoltageDC12V / DC24V
Maximum Load10A
Operating Frequency315MHz / 433MHz (Automatic matching)
Receiver Sensitivity-100dBm
Encoding TypeLearning Code
Channel1
Wireless CommunicationRF
UseUniversal
PCB Size (L x W x H)55mm x 32mm x 17mm
Remote Control Size (L x W x H)Approx. 55mm x 30mm x 13mm (2.2 x 1.2 x 0.5 inch)
OriginMainland China
CertificationCE
High-concerned chemicalNone
Support APPNo
PackageNo (Refers to retail packaging)

4. Package Contents

The package typically includes:

  • RF Wireless Receiver Module (AK-YK68-02S)
  • Remote Control Transmitter (Quantity may vary based on order)

Note: The number of receiver modules and remote controls may vary depending on the specific product variant purchased.

Single receiver board and remote control

Figure 1: Single receiver board and remote control.

Multiple receiver boards and a remote control

Figure 2: Example of a kit with multiple receiver boards and a remote control.

5. Setup and Wiring

5.1 Receiver Board Overview

Familiarize yourself with the components on the receiver board:

Close-up of the receiver board showing learning button, indicator light, and terminals

Figure 3: Receiver board with labeled components (Learning Button, Indicator Light, IN/OUT terminals).

5.2 Wiring Diagrams

Ensure all power is disconnected before performing any wiring. Connect the receiver according to the appropriate diagram for your load type.

5.2.1 Wiring for DC12V Load (e.g., Motor)

Wiring diagram for controlling a DC12V load

Figure 4: Wiring diagram for controlling a DC12V load. Connect DC12V+ and DC12V- to the IN terminals. Connect the load (e.g., motor) to the NO (Normally Open) and COM (Common) terminals of the relay.

5.2.2 Wiring for 1V-260V Load (e.g., Light Bulb)

Wiring diagram for controlling a 1V-260V load

Figure 5: Wiring diagram for controlling a 1V-260V load. Connect the DC12V input to the IN terminals. Connect the load power (1V-260V) through the relay's NO (Normally Open) and COM (Common) terminals.

5.3 Learning and Removing Remote Control Codes

5.3.1 Learning a Remote Control

  1. Press the 'Learning Button' on the receiver board (refer to Figure 3). The indicator light will flash.
  2. Release your finger from the 'Learning Button'.
  3. Press any button on your remote control. The indicator light on the receiver will flash two times and then turn off.
  4. This indicates that the remote control has been successfully learned by the receiver.

The receiver can learn codes from more than 12 remote controls using 2262 or 1527 chip types.

5.3.2 Removing All Learned Remote Control Codes

  1. Press and hold the 'Learning Button' on the receiver board for approximately 8 seconds.
  2. The indicator light will turn on and then turn off.
  3. This signifies that all previously stored remote control information has been successfully removed from the receiver.

5.4 Adjusting Working Mode (Jumper Settings)

The receiver board features jumper pins to adjust its working mode. Refer to Figure 3 for the location of the jumper pins. The common modes are:

  • T 1-2 (Toggle Mode): Press the remote button once to turn the relay ON, press the same button again to turn the relay OFF.
  • L 2-3 (Latched Mode): Press button 1 on the remote to turn the relay ON, press button 2 on the remote to turn the relay OFF. (Requires a multi-button remote).
  • M Non-occupation (Momentary Mode): Press and hold the remote button to turn the relay ON, release the button to turn the relay OFF.

6. Operating Instructions

Once the receiver is correctly wired and the remote control is learned, operate the device as follows:

  1. Ensure the receiver is powered on and connected to your desired load.
  2. Use the remote control to send commands to the receiver. The behavior of the relay (ON/OFF) will depend on the selected working mode (Toggle, Latched, or Momentary).
  3. The remote control's slidable cover helps prevent accidental button presses.

7. Maintenance

  • Keep the receiver and remote control clean and dry. Avoid exposure to moisture or extreme temperatures.
  • Do not attempt to disassemble or modify the device, as this may void any potential warranty and could lead to malfunction or damage.
  • Regularly check wiring connections to ensure they are secure and free from corrosion.
  • If the remote control range decreases, check the battery in the remote control and replace if necessary.

8. Troubleshooting

ProblemPossible CauseSolution
Receiver does not respond to remote control.Remote not learned, remote battery low, incorrect frequency, or receiver power issue.Ensure receiver is powered. Re-learn the remote control (Section 5.3.1). Replace remote battery. Verify remote and receiver frequencies match (315MHz/433MHz).
Relay does not switch ON/OFF.Incorrect wiring, faulty relay, or power supply issue to the load.Check all wiring connections against diagrams (Section 5.2). Ensure the power supply to the load is correct and functional. If the relay itself is suspected to be defective, professional inspection may be required.
Short operating range.Obstructions, interference, or low remote battery.Minimize physical obstructions between remote and receiver. Avoid strong electromagnetic interference. Replace remote battery.
Receiver indicator light does not flash during learning.Receiver not powered or learning button malfunction.Verify receiver power supply. Ensure the learning button is pressed correctly.

9. User Tips

  • When setting up, always double-check your wiring before applying power to prevent damage to the device or connected equipment.
  • If you experience issues with the relay not activating, ensure both the receiver and the load have the correct voltage applied.
  • For applications requiring precise control, test the different working modes (Toggle, Latched, Momentary) to find the one best suited for your needs.

10. Warranty and Support

For detailed item guides and documents, including a user manual in PDF format, please refer to the official documentation available here.

Please retain your proof of purchase for any warranty claims. For technical support or further assistance, please contact the seller or refer to the product listing for contact information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.