LiitoKala 33140

Contents

LiitoKala 3.2V 15Ah LiFePO4 Battery Cell User Manual

Model: 33140

1. Introduction

This manual provides essential information for the safe and effective use of LiitoKala 3.2V 15Ah LiFePO4 battery cells, model 33140. These cylindrical lithium-ion rechargeable cells are designed for various applications including electric vehicles, e-bikes, e-scooters, power tools, solar energy systems, and DIY battery packs. Please read this manual thoroughly before use.

Multiple LiFePO4 battery cells, 3.2V 15Ah
Figure 1: LiitoKala 3.2V 15Ah LiFePO4 Battery Cells

2. Safety Warnings and Precautions

Failure to follow these safety instructions can result in fire, personal injury, or property damage. Users must be familiar with the safe use of lithium batteries.

  • Fire Risk: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
  • Do not expose the cell to extreme heat or flame.
  • Do not short circuit, over-charge, or over-discharge the cell.
  • Do not subject the cell to strong mechanical shocks.
  • Do not immerse the cell in water or seawater, or allow it to get wet.
  • Do not reverse the polarity of the cell for any reason.
  • Do not disassemble or modify the cell.
  • Do not handle or store the cell with metallic objects like necklaces, coins, or hairpins, as this can cause a short circuit.
  • Do not use the cell if it has conspicuous damage or deformation.
  • Do not connect the cell directly to a plug socket or car-cigarette-plug.
  • Do not make direct soldering onto the cell.
  • Do not touch a leaked cell directly.
  • Do not use the cell for other equipment without proper knowledge and a suitable Battery Management System (BMS).
  • Do not mix Lithium-ion cells with other battery types.
  • Do not use or leave the cell under direct blazing sun or in a heated car.
  • Keep the cell away from children.
  • Do not drive a nail into the cell, strike it with a hammer, or tread on it.
  • Do not impact or fling the cell.

3. Specifications

The LiitoKala 33140 LiFePO4 battery cell features high energy density, excellent cycle life, and low internal resistance, making it suitable for various applications.

Product parameter table for LiitoKala 33140 LiFePO4 cell
Figure 2: Key Product Parameters

3.1. General Parameters

Parameter Value
BrandLiitoKala
Model Number33140
TypeLiFePO4
Nominal Voltage3.2V
Nominal Capacity15Ah (15000mAh)
Internal Resistance<8 mΩ
Size (Diameter*Length)33mm * 140mm
WeightAbout 268g
Cycle Life (DOD 80%)More than 2000 times
OriginMainland China
CertificationNONE

3.2. Electrical Characteristics

Characteristic Value Notes
Full Voltage3.65V
Lowest Voltage (Discharge Cut-off)1.8V
Input Charging Voltage3.65V/cell
Input Charging Current5A (0.5C)Recommended
Continuous Discharging Current75A (5C)
Max Current Discharge5C
Charging Temperature0°C ~ 45°C
Discharging Temperature-20°C ~ 60°C
Storage Temperature-20°C ~ 45°C
Storage Humidity<70% RH

4. Setup and Installation

These LiFePO4 cells are designed for DIY battery pack assembly. They can be combined in various series (e.g., 3s, 4s, 8s, 10s, 13s) to achieve desired voltage and capacity. The cells are supplied with nickel for direct welding, facilitating custom pack creation.

4.1. DIY Battery Pack Assembly Considerations

  • Ensure all cells are balanced in voltage before assembly.
  • Use appropriate welding techniques (e.g., spot welding) to connect cells with nickel strips.
  • Always use a suitable Battery Management System (BMS) for your assembled battery pack to ensure safe charging, discharging, and cell balancing.
  • Proper insulation and enclosure are critical for safety and durability.
A single LiitoKala 3.2V 15Ah LiFePO4 cell, showing the positive terminal with welding points
Figure 3: Cell terminal with welding points
A LiFePO4 cell connected to a testing device with wires and alligator clips
Figure 4: Cell connected to a testing device

5. Operation

5.1. Charging

  • Charging Method: Use the Constant Current-Constant Voltage (CC-CV) method.
  • Standard Charge: Charge at a constant current of 0.5C (7500mA) until the cell voltage reaches 3.65V. Then, switch to constant voltage charging at 3.65V until the charging current drops below 0.05C.
  • Charging Current Limit: Do not exceed 1C (15000mA) charging current.
  • Charging Temperature: The ambient temperature range for charging is 0°C to 55°C.
  • For maximum capacity, maintain the charge voltage at 3.65V for 1 hour after reaching full voltage.

5.2. Discharging

  • Standard Discharge: Discharge at a constant current of 0.5C until the cell voltage reaches 2.5V.
  • Discharge Cut-off Voltage: The recommended discharge cut-off voltage is 2.5V. Do not discharge below 1.8V.
  • Maximum Continuous Discharge Current: The recommended maximum continuous discharge current is 45000mA (3C).
  • Discharging Temperature: The ambient temperature range for discharging is -20°C to 60°C.

6. Maintenance and Storage

6.1. Storage Recommendations

  • Short-Term Storage (less than 3 months): Store the cells at an ambient temperature of 0°C to 45°C.
  • Long-Term Storage (more than 3 months): Store the cells at an ambient temperature of 0°C to 25°C.
  • Maintain low humidity and ensure no corrosive gas atmosphere.
  • Do not apply pressure to the cells during storage.
  • Store cells with approximately 30% charge.

6.2. Disposal

For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements. Do not dispose of batteries with regular household waste.

7. Troubleshooting

If you encounter any issues with your LiitoKala LiFePO4 battery cells, please consider the following:

  • Capacity Discrepancies: Ensure proper testing procedures are followed, ideally with a dedicated battery testing device or a BMS that monitors actual capacity.
  • Voltage Instability: Verify connections are secure and that the cells are balanced. An unbalanced cell pack can lead to performance issues.
  • Overheating: Immediately disconnect the battery if it becomes excessively hot. Review charging/discharging parameters and ensure they are within specified limits.
  • For complex issues or persistent problems, please contact LiitoKala customer support.

8. User Tips

  • Upon receiving new cells, it is good practice to check their initial voltage. Cells typically arrive with a voltage around 3.2V.
  • When building a battery pack, testing individual cell capacity and internal resistance can help ensure a balanced and high-performing pack.
  • Always use a reliable Battery Management System (BMS) to protect your LiFePO4 cells from overcharge, over-discharge, overcurrent, and to balance cell voltages.

9. Warranty and Support

The warranty period for the cell is determined by the business contract. LiitoKala will not replace a new cell for free if the problem is not due to a manufacturing process failure but rather due to customer's abuse or misuse. This includes, but is not limited to:

  • Trouble occurred by handling outside of the precautions in this instruction manual.
  • Trouble occurred by incorrect matching of electric circuit, cell pack, and charger.
  • Defects in cells during assembly after acceptance.

For further consultation or support, please contact LiitoKala:

  • Address: 6F building 5, MaoBang industrial Area, Gentleman's cloth, GuanLan Town, Baoan District, Shenzhen City, Guangdong, China
  • Email: sales@liitokala.com.cn
  • Website: http://www.liitokalar.com.cn

A detailed PDF user manual is also available for reference: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.