1. Introduction
Thank you for choosing the Baofeng K61 PRO Multi-Band Amateur Radio. This device utilizes advanced technology for reliable communication, offering stability and long-distance capabilities in a compact design. It includes features such as emergency alarm, personnel death alarm, work alone mode, and analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode.
To ensure proper operation and maximize the convenience of this product, please read this manual and the Safety Information Manual before use.
Important Warnings
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
ATTENTION! When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequencies into a new saved code plug to avoid errors. Programming must comply with your FCC (or EU/other country) license certification.
FRS, GMRS, MURS, PMR446: Use of this transceiver on FRS, GMRS, MURS (USA) or PMR446 (Europe) frequencies is illegal due to specific band restrictions.
2. Safety Warnings and RF Exposure Guidelines
To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures.
General Guidelines
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany the device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions
- Transmit no more than the rated duty factor of 50% of the time. Press the Push-to-Talk (PTT) key to transmit and release it to receive.
- Keep the radio unit at least 2.5cm away from your face. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, body harness, or use the correct clip.
- Use of non-approved antennas, batteries, and accessories may cause the radio to exceed FCC RF exposure guidelines.
Operating Prohibitions
- Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not operate the product near any blasting area.
- Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where wireless communication equipment is prohibited.
Precautions for Batteries
- Do not charge or replace your battery in a location containing fuels, chemicals, or explosive materials.
- Do not charge a wet battery; dry it with a soft, clean cloth first.
- Do not charge a battery suffering deformation, leakage, or overheating.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location with strong radiation.
- Overcharge is prohibited as it may shorten battery life.
3. Package Contents
Your Baofeng K61 PRO transceiver comes with the following items:
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Instruction Manual (PDF available at User Manual PDF)
- 1 Belt Clip
- 1 Desk charger (With wall-wart)
- 1 Antenna
- 1 Wrist Belt
- 1 Type-C USB Cable
If any item is missing, please contact your dealer.

4. Features and Functions
The Baofeng K61 PRO offers a wide range of features for versatile communication:
- 1.54" TFT large screen, full keyboard, fully open menu operation.
- Scanner function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, scan channel addition and removal.
- Multi-band scanning receiver: 108-136MHz (AM RX), 136-174MHz (RX/TX), 220-260MHz (RX/TX), 350-390MHz (RX), 400-520MHz (RX/TX), 65-108MHz (FM RX), 480-600MHz (RX).
- Built-in input method for editing channel names.
- NOAA Weather Radio Channel Reception (USA and Canada).
- Selectable frequency steps: 2.5K, 5.0K, 6.25K, 8.33K, 10K, 12.5K, 20K, 25K, 30K, 50K, 100KHz.
- Type-C direct charging and charging stand support.
- High Capacity Lithium-Ion battery.
- 50 CTCSS tones and 105 DCS codes.
- Up to 640 named memory channels.
- High or low power selectable.
- LED flashlight.
- Ten (10) levels of Squelch adjustment.
- DTMF encoder and manual dial.
- Broadcast FM radio receiver 87.5-108 MHz.
- VOX (voice activated transmit).
- Alarm function.
- Dual watch / Dual reception.
- PC programmable.
- Analog signaling: DTMF, 2TONE, 5TONE, BDC1200 codecs.



5. Radio Overview: Buttons and Controls
Familiarize yourself with the layout of your Baofeng K61 PRO radio:
- Antenna
- LED flashlight
- Status LED (TX/RX LED)
- Power / Volume knob
- Battery release latch
- PTT - Push to talk
- SK1-Programmable key (flashlight/alarm switch)
- SK2-Programmable Key (Radio/Monitor)
- Accessory jack
- Type-C charging indicator
- V/M-VFO/MR mode key
- A / B select key
- SWEEP key
- MENU Key
- Type-C charging port
- Color LCD
- Speaker
- Microphone
- EXIT Key
- Keypad

6. Setup
6.1 Battery Information and Charging
The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge and discharge the battery two or three times initially.
Charging Procedure
- Plug the AC adaptor into an outlet, then connect the cable to the DC jack on the charger. The indicator blinks orange.
- Place the battery or radio into the charger, ensuring good contact. The indicator turns red, indicating charging.
- Charging takes approximately 2-5 hours. The lamp turns green when charging is complete.
LED Indicator Status
| Status | LED Indication |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble (e.g., battery too warm, short-circuited) | Red blinks fast |
Using the Type-C USB Charger
- Ensure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery.
- Connect the other end of the cable to a USB power source (wall adapter, PC, power bank, vehicle charger).
- An empty battery will be fully charged in about 4 hours. The battery meter on the LCD will indicate charging.

6.2 Installing Accessories
Installing/Removing the Antenna
- Installing: Screw the antenna clockwise into the connector on top of the transceiver until secure.
- Removing: Turn the antenna counter-clockwise to remove it.
Installing the Belt Clip
- Remove the two parallel screws on the back of the radio above the battery.
- Thread these screws through the holes on the belt clip and screw them back into the radio body.
Installing the Battery Pack
- Ensure the radio is turned off.
- Align the battery parallel with the radio body, with the lower edge about 1-2cm below the radio's edge.
- Slide the battery upward along the guide-rails until it clicks into place.
Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and insert the Speaker / Microphone plug into the double jack.

7. Operating Instructions
7.1 Basic Operations
Power On/Off
- To turn on: Rotate the Volume/Power knob clockwise until you hear a