1. Introduction
This manual provides instructions for installing and operating the Wireless Carplay & Android Auto Module, designed to integrate smartphone functionality with your vehicle's existing SMEG or MRN multimedia system. The module enables both wireless and wired connections for Apple CarPlay and Android Auto, allowing for voice command control of phone functions, navigation, music, and more.
The module supports the built-in vehicle machine interaction system of iPhone, cooperating with the central control knob button to provide voice command and control of phone, information, navigation, and music. It also supports Siri voice interaction. For Android devices, it integrates with the original ecological Android car-machine interaction system, offering voice control for phone, information, navigation, and music.
Additionally, the smart module can decode video and supports rear-view video input, allowing for the integration of a rear-view camera system.
2. Package Contents
Verify that all items are present in the package:
- Apple CarPlay Module (Main Unit)
- Power Cable
- CAN Gateway Cable
- WIFI Antenna
- User's Manual (this document)
3. Installation
3.1 Important Safety Information
CAUTION: Always ensure the CarPlay POWER is disconnected before adjusting the DIP switches. Connect the CarPlay POWER only after the DIP switches are correctly set.
It is recommended to use a soft towel or protective covering on surfaces during installation to prevent scratches to your vehicle's interior.
3.2 System Compatibility Check
This module is designed for Peugeot and Citroen vehicles equipped with SMEG or MRN multimedia systems. Before installation, verify your car's system version. An example of a system information screen is shown below:
3.3 DIP Switch Settings
The DIP switches on the module must be configured according to your vehicle's model and screen size. Refer to the table below for common settings. Ensure power is disconnected before making any changes.
| 1 | 2 | Car Model |
|---|---|---|
| OFF | OFF | Default |
| OFF | ON | Another reverse data |
| 3 | 4 | Screen Size |
| OFF | OFF | 800*480 7" |
3.4 Wiring Diagram and Connections
Follow the detailed wiring diagram for connecting the module to your vehicle's system. Pay close attention to each connection point.
- Power Cable:
- Yellow: B+
- Red: ACC
- Black: GND
- Camera Connections:
- Blue: Camera Power Supply
- Brown: Rear detect (Connect to rearview light cable or 360 panoramic detection cable)
- REAR-CVBS: Connect to rearview camera or 360 degree panoramic AHD output
- FRONT-CVBS: Connect to the frontview camera
- 360 Panoramic System:
- White: 360-TX (Connected to 360 panoramic universal box TXD)
- White and Black: 360-RX (Connected to 360 panoramic universal box TXD)
- Audio Output: AUX
- USB: Connect mobile phone, USB flash drive, software upgrade.
- LVDS Connection: Connect to the original vehicle LVDS. When inserting, ensure it is properly seated.
Note on Optical Fiber Cable: If your original power cable includes an optical fiber cable, you must transfer it to the power cable of the CarPlay box.
3.5 Audio Setup for Carplay/Android Auto
For audio output, before switching to the CarPlay/Android Auto interface:
- Connect your phone to the original car's Bluetooth for both calls and media. Select the original car audio on the Bluetooth stereo interface.
- Alternatively, switch the original car sound channel to the AUX channel.
4. Operating Instructions
4.1 Wireless CarPlay Connection
To connect your iPhone wirelessly to CarPlay:
- On your iPhone, open Wi-Fi and Bluetooth settings.
- On the module interface, click "Discover and connect device".
- Select the Bluetooth device name starting with "CX_BT....." and pair your iPhone.
4.2 Wireless Android Auto Connection
To connect your Android phone wirelessly to Android Auto:
- On your Android phone, open Wi-Fi and Bluetooth settings.
- On the module interface, click "CX-BTXXXX" (the specific Bluetooth name) and pair the device.
4.3 General Functions and Interface
The module provides a range of functions including navigation, Siri/voice control, phone calls, USB media playback, online music, and screen mirroring.
Video 4.1: Demonstration of Android Auto and CarPlay interface on SMEG/SMEG+ multimedia system.
4.4 Steering Wheel Button Control
The module integrates with your vehicle's steering wheel buttons for convenient control:
- Long press: Switch between systems.
- Short press: Connect/hang up phone calls. Long press to activate voice control (without using the original car Bluetooth).
- Short press: Increase or decrease volume.
4.5 Car System Settings for Module Integration
After installation, configure your car's multimedia settings:
- Audio Settings: Ensure "use the original Bluetooth Audio" is set to OFF or ON as needed, and select "Original multimedia selection aux".
- Cell Phone Bluetooth Connection: Connect your mobile phone to the car's original Bluetooth for audio playback.
The module supports original camera and parking sensor display. Front view camera is supported, and aftermarket reverse cameras are also supported.
5. Maintenance
The Wireless Carplay & Android Auto Module is designed for durability and minimal maintenance. Keep the unit free from dust and moisture. Avoid exposing it to extreme temperatures. Do not attempt to open the module casing, as this may void any applicable warranty and could cause damage.
6. Troubleshooting
If you encounter issues with the module, refer to the following troubleshooting steps:
- Screen not showing normally: Check the LVDS cable connection and ensure the DIP switches are set correctly according to your car model.
- Sound problems: Verify that the car's Multimedia and install system settings are configured correctly. Ensure your phone is connected to the car's original Bluetooth and multimedia Bluetooth mode is selected for audio playback, or that the AUX channel is selected.
- Main unit pilot lamp not working: Check the power cable connection and the fuse.
- No display on black screen after installation:
- Check the LVDS cable line. It should be connected to the back of the main unit, not directly to the back of the screen.
- Confirm the DIP switch is set correctly.
- How to confirm the correct LVDS cable wire: If the screen turns black after unplugging the LVDS cable line from the back of the car host, it indicates the correct cable.
- Connecting Wireless CarPlay and Android Auto: Your mobile phone only needs to connect to the module's Bluetooth. The mobile phone's Bluetooth idle state should not be connected to other devices like watch recorders. Connecting to the module's Bluetooth will automatically initiate Wi-Fi transmission; you do not need to manually enter a password for Wi-Fi.
7. Specifications
| Feature | Specification |
|---|---|
| Operating Voltage | 9 - 16V |
| Operating Temperature | -30 ~ +75°C |
| Stored Temperature | -30 ~ +85°C |
| Environment Humidity | ≤ 98% (at 45°C), 65 ± 5% (rated) |
| Power Consumption | 500mA (rated), 3A (Max) |
| Shutdown Current | 3 mA (Clock is on) |
| Quiescent Current | Less than 3 mA |
| Charging Current | ≤ 2A (If USB charging current > 1A, the host activates circuit protection to control current below 1.5A to prevent product damage.) |
8. User Tips
- If your vehicle has a CD player located above the original SMEG unit, routing all the extra cables can be challenging due to limited space. Patience and careful cable management are recommended.
- Always place a soft towel or protective covering over your car's interior surfaces during installation to prevent accidental scratches.
- For proper functionality of your original rearview camera, ensure DIP switch #2 on the module is set to the 'ON' position.
- Audio for CarPlay and Android Auto is typically transmitted via Bluetooth by connecting your smartphone to the car's original Bluetooth system. Alternatively, you can select the AUX input on your car's multimedia system for sound output.
- Some users have noted that the LVDS cable provided might be a bit short for certain installations, potentially requiring creative routing or module placement.
- The module's interface might exhibit slight delays for some users.
- When using Android Auto, the module may connect immediately and switch over to the Android Auto interface. This behavior is inherent to Android Auto and cannot be disabled through the module's settings. Using a wired connection (USB) instead of wireless (Wi-Fi/Bluetooth) might bypass this automatic switch.
9. Warranty and Support
For detailed warranty information and further support, please refer to the official product documentation or contact CARABC customer service. A comprehensive user manual in PDF format is available for download: